s32 ret_val;
u16 i, rar_count = mac->rar_entry_count;
+ if ((hw->mac.type >= e1000_i210) &&
+ !(igb_get_flash_presence_i210(hw))) {
+ ret_val = igb_pll_workaround_i210(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
/* Initialize identification LED */
ret_val = igb_id_led_init(hw);
if (ret_val) {
/* Extended Device Control */
#define E1000_CTRL_EXT_SDP3_DATA 0x00000080 /* Value of SW Defineable Pin 3 */
/* Physical Func Reset Done Indication */
-#define E1000_CTRL_EXT_PFRSTD 0x00004000
-#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
-#define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000
-#define E1000_CTRL_EXT_LINK_MODE_1000BASE_KX 0x00400000
-#define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000
-#define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000
-#define E1000_CTRL_EXT_EIAME 0x01000000
-#define E1000_CTRL_EXT_IRCA 0x00000001
+#define E1000_CTRL_EXT_PFRSTD 0x00004000
+#define E1000_CTRL_EXT_SDLPE 0X00040000 /* SerDes Low Power Enable */
+#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_1000BASE_KX 0x00400000
+#define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000
+#define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000
+#define E1000_CTRL_EXT_EIAME 0x01000000
+#define E1000_CTRL_EXT_IRCA 0x00000001
/* Interrupt delay cancellation */
/* Driver loaded bit for FW */
#define E1000_CTRL_EXT_DRV_LOAD 0x10000000
/* packet buffer parity error detection enabled */
/* descriptor FIFO parity error detection enable */
#define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */
+#define E1000_CTRL_EXT_PHYPDEN 0x00100000
#define E1000_I2CCMD_REG_ADDR_SHIFT 16
#define E1000_I2CCMD_PHY_ADDR_SHIFT 24
#define E1000_I2CCMD_OPCODE_READ 0x08000000
/* These functions must be implemented by drivers */
s32 igb_read_pcie_cap_reg(struct e1000_hw *hw, u32 reg, u16 *value);
s32 igb_write_pcie_cap_reg(struct e1000_hw *hw, u32 reg, u16 *value);
+
+void igb_read_pci_cfg(struct e1000_hw *hw, u32 reg, u16 *value);
+void igb_write_pci_cfg(struct e1000_hw *hw, u32 reg, u16 *value);
#endif /* _E1000_HW_H_ */
}
return ret_val;
}
+
+/**
+ * igb_pll_workaround_i210
+ * @hw: pointer to the HW structure
+ *
+ * Works around an errata in the PLL circuit where it occasionally
+ * provides the wrong clock frequency after power up.
+ **/
+s32 igb_pll_workaround_i210(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u32 wuc, mdicnfg, ctrl, ctrl_ext, reg_val;
+ u16 nvm_word, phy_word, pci_word, tmp_nvm;
+ int i;
+
+ /* Get and set needed register values */
+ wuc = rd32(E1000_WUC);
+ mdicnfg = rd32(E1000_MDICNFG);
+ reg_val = mdicnfg & ~E1000_MDICNFG_EXT_MDIO;
+ wr32(E1000_MDICNFG, reg_val);
+
+ /* Get data from NVM, or set default */
+ ret_val = igb_read_invm_word_i210(hw, E1000_INVM_AUTOLOAD,
+ &nvm_word);
+ if (ret_val)
+ nvm_word = E1000_INVM_DEFAULT_AL;
+ tmp_nvm = nvm_word | E1000_INVM_PLL_WO_VAL;
+ for (i = 0; i < E1000_MAX_PLL_TRIES; i++) {
+ /* check current state directly from internal PHY */
+ igb_read_phy_reg_gs40g(hw, (E1000_PHY_PLL_FREQ_PAGE |
+ E1000_PHY_PLL_FREQ_REG), &phy_word);
+ if ((phy_word & E1000_PHY_PLL_UNCONF)
+ != E1000_PHY_PLL_UNCONF) {
+ ret_val = 0;
+ break;
+ } else {
+ ret_val = -E1000_ERR_PHY;
+ }
+ /* directly reset the internal PHY */
+ ctrl = rd32(E1000_CTRL);
+ wr32(E1000_CTRL, ctrl|E1000_CTRL_PHY_RST);
+
+ ctrl_ext = rd32(E1000_CTRL_EXT);
+ ctrl_ext |= (E1000_CTRL_EXT_PHYPDEN | E1000_CTRL_EXT_SDLPE);
+ wr32(E1000_CTRL_EXT, ctrl_ext);
+
+ wr32(E1000_WUC, 0);
+ reg_val = (E1000_INVM_AUTOLOAD << 4) | (tmp_nvm << 16);
+ wr32(E1000_EEARBC_I210, reg_val);
+
+ igb_read_pci_cfg(hw, E1000_PCI_PMCSR, &pci_word);
+ pci_word |= E1000_PCI_PMCSR_D3;
+ igb_write_pci_cfg(hw, E1000_PCI_PMCSR, &pci_word);
+ usleep_range(1000, 2000);
+ pci_word &= ~E1000_PCI_PMCSR_D3;
+ igb_write_pci_cfg(hw, E1000_PCI_PMCSR, &pci_word);
+ reg_val = (E1000_INVM_AUTOLOAD << 4) | (nvm_word << 16);
+ wr32(E1000_EEARBC_I210, reg_val);
+
+ /* restore WUC register */
+ wr32(E1000_WUC, wuc);
+ }
+ /* restore MDICNFG setting */
+ wr32(E1000_MDICNFG, mdicnfg);
+ return ret_val;
+}
s32 igb_write_xmdio_reg(struct e1000_hw *hw, u16 addr, u8 dev_addr, u16 data);
s32 igb_init_nvm_params_i210(struct e1000_hw *hw);
bool igb_get_flash_presence_i210(struct e1000_hw *hw);
+s32 igb_pll_workaround_i210(struct e1000_hw *hw);
#define E1000_STM_OPCODE 0xDB00
#define E1000_EEPROM_FLASH_SIZE_WORD 0x11
#define NVM_LED_1_CFG_DEFAULT_I211 0x0184
#define NVM_LED_0_2_CFG_DEFAULT_I211 0x200C
+/* PLL Defines */
+#define E1000_PCI_PMCSR 0x44
+#define E1000_PCI_PMCSR_D3 0x03
+#define E1000_MAX_PLL_TRIES 5
+#define E1000_PHY_PLL_UNCONF 0xFF
+#define E1000_PHY_PLL_FREQ_PAGE 0xFC0000
+#define E1000_PHY_PLL_FREQ_REG 0x000E
+#define E1000_INVM_DEFAULT_AL 0x202F
+#define E1000_INVM_AUTOLOAD 0x0A
+#define E1000_INVM_PLL_WO_VAL 0x0010
+
#endif
#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */
#define E1000_PBS 0x01008 /* Packet Buffer Size */
#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */
+#define E1000_EEARBC_I210 0x12024 /* EEPROM Auto Read Bus Control */
#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */
#define E1000_I2CCMD 0x01028 /* SFPI2C Command Register - RW */
#define E1000_FRTIMER 0x01048 /* Free Running Timer - RW */
}
}
+void igb_read_pci_cfg(struct e1000_hw *hw, u32 reg, u16 *value)
+{
+ struct igb_adapter *adapter = hw->back;
+
+ pci_read_config_word(adapter->pdev, reg, value);
+}
+
+void igb_write_pci_cfg(struct e1000_hw *hw, u32 reg, u16 *value)
+{
+ struct igb_adapter *adapter = hw->back;
+
+ pci_write_config_word(adapter->pdev, reg, *value);
+}
+
s32 igb_read_pcie_cap_reg(struct e1000_hw *hw, u32 reg, u16 *value)
{
struct igb_adapter *adapter = hw->back;
projects / linux / commitdiff