#define __KERNEL_SYSCALLS__
#include <linux/module.h>
-#include <linux/init.h>
#include <linux/kmod.h>
#include <linux/delay.h>
#include <linux/fs.h>
#include <linux/poll.h>
#include <linux/unistd.h>
#include <linux/byteorder/swabb.h>
-#include <linux/slab.h>
#include <linux/smp_lock.h>
#include <stdarg.h>
#include <linux/ptrace.h>
#include <linux/ioport.h>
#include <linux/in.h>
-#include <linux/slab.h>
#include <linux/string.h>
#include <linux/pci.h>
-#include <linux/init.h>
#include <linux/vmalloc.h>
#include <linux/netdevice.h>
#include <linux/inetdevice.h>
static int pids_off;
static int adac=DVB_ADAC_TI;
static int hw_sections = 1;
+static int rgb_on = 0;
int av7110_num = 0;
* DEBI functions
****************************************************************************/
+#define wait_for_debi_done(x) \
+ saa7146_wait_for_debi_done(x->dev) \
+
/* This DEBI code is based on the Stradis driver
by Nathan Laredo <laredo@gnu.org> */
-static int wait_for_debi_done(struct av7110 *av7110)
-{
- struct saa7146_dev *dev = av7110->dev;
- int start;
-
- /* wait for registers to be programmed */
- start = jiffies;
- while (1) {
- if (saa7146_read(dev, MC2) & 2)
- break;
- if (jiffies-start > HZ/20) {
- printk ("%s: timed out while waiting for registers "
- "getting programmed\n", __FUNCTION__);
- return -ETIMEDOUT;
- }
- }
-
- /* wait for transfer to complete */
- start = jiffies;
- while (1) {
- if (!(saa7146_read(dev, PSR) & SPCI_DEBI_S))
- break;
- saa7146_read(dev, MC2);
- if (jiffies-start > HZ/4) {
- printk ("%s: timed out while waiting for transfer "
- "completion\n", __FUNCTION__);
- return -ETIMEDOUT;
- }
- }
-
- return 0;
-}
-
static int debiwrite(struct av7110 *av7110, u32 config,
int addr, u32 val, int count)
{
{
struct dvb_demux_feed *dvbdmxfeed=(struct dvb_demux_feed *) p2t->priv;
- DEB_EE(("struct dvb_filter_pes2ts:%p\n",p2t));
+// DEB_EE(("struct dvb_filter_pes2ts:%p\n",p2t));
if (!(dvbdmxfeed->ts_type & TS_PACKET))
return 0;
return dvbdmxfeed->cb.ts(buf, len, 0, 0,
&dvbdmxfeed->feed.ts, DMX_OK);
else
- return dvb_filter_pes2ts(p2t, buf, len);
+ return dvb_filter_pes2ts(p2t, buf, len, 1);
}
static int dvb_filter_pes2ts_cb(void *priv, unsigned char *data)
{
struct dvb_demux_feed *dvbdmxfeed=(struct dvb_demux_feed *) priv;
- DEB_EE(("dvb_demux_feed:%p\n",dvbdmxfeed));
+// DEB_EE(("dvb_demux_feed:%p\n",dvbdmxfeed));
dvbdmxfeed->cb.ts(data, 188, 0, 0,
&dvbdmxfeed->feed.ts,
txbuf=irdebi(av7110, DEBINOSWAP, TX_BUFF, 0, 2);
len=(av7110->debilen+3)&(~3);
- DEB_D(("GPIO0 irq %d %d\n", av7110->debitype, av7110->debilen));
+// DEB_D(("GPIO0 irq %d %d\n", av7110->debitype, av7110->debilen));
print_time("gpio");
- DEB_D(("GPIO0 irq %02x\n", av7110->debitype&0xff));
+// DEB_D(("GPIO0 irq %02x\n", av7110->debitype&0xff));
switch (av7110->debitype&0xff) {
case DATA_TS_PLAY:
buf[1] = div & 0xff;
buf[2] = 0x8e;
- if (freq < (u32) (16*168.25) )
+ if (freq < (u32) 16*168.25 )
config = 0xa0;
- else if (freq < (u32) (16*447.25))
+ else if (freq < (u32) 16*447.25)
config = 0x90;
else
config = 0x30;
av7110->pids[DMX_PES_TELETEXT], 0,
av7110->pids[DMX_PES_PCR]);
outcom(av7110, COMTYPE_PIDFILTER, Scan, 0);
- } else
+ } else {
SetPIDs(av7110, 0, 0, 0, 0, 0);
+ outcom(av7110, COMTYPE_PIDFILTER, FlushTSQueue, 0);
+ }
up(&av7110->pid_mutex);
}
get recognized before the main driver is fully loaded */
saa7146_write(dev, GPIO_CTRL, 0x500000);
- saa7146_i2c_adapter_prepare(dev, NULL, SAA7146_I2C_BUS_BIT_RATE_3200);
+ saa7146_i2c_adapter_prepare(dev, NULL, SAA7146_I2C_BUS_BIT_RATE_120); /* 275 kHz */
av7110->i2c_bus = dvb_register_i2c_bus (master_xfer, dev,
av7110->dvb_adapter, 0);
/* set dd1 stream a & b */
saa7146_write(dev, DD1_STREAM_B, 0x00000000);
- saa7146_write(dev, DD1_INIT, 0x02000000);
+ saa7146_write(dev, DD1_INIT, 0x03000000);
saa7146_write(dev, MC2, (MASK_09 | MASK_25 | MASK_10 | MASK_26));
/* upload all */
memcpy(standard,dvb_standard,sizeof(struct saa7146_standard)*2);
/* set dd1 stream a & b */
saa7146_write(dev, DD1_STREAM_B, 0x00000000);
- saa7146_write(dev, DD1_INIT, 0x02000700);
+ saa7146_write(dev, DD1_INIT, 0x03000700);
saa7146_write(dev, MC2, (MASK_09 | MASK_25 | MASK_10 | MASK_26));
}
else if (dev->pci->subsystem_vendor == 0x110a) {
// switch DVB SCART on
outcom(av7110, COMTYPE_AUDIODAC, MainSwitch, 1, 0);
outcom(av7110, COMTYPE_AUDIODAC, ADSwitch, 1, 1);
- //saa7146_setgpio(dev, 1, SAA7146_GPIO_OUTHI); // RGB on, SCART pin 16
+ if (rgb_on)
+ saa7146_setgpio(dev, 1, SAA7146_GPIO_OUTHI); // RGB on, SCART pin 16
//saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTLO); // SCARTpin 8
}
{
struct av7110 *av7110 = (struct av7110*)dev->ext_priv;
- DEB_INT(("dev: %p, av7110: %p\n",dev,av7110));
+// DEB_INT(("dev: %p, av7110: %p\n",dev,av7110));
if (*isr & MASK_19)
tasklet_schedule (&av7110->debi_tasklet);
static struct saa7146_standard analog_standard[] = {
{
.name = "PAL", .id = V4L2_STD_PAL_BG,
- .v_offset = 0x18, .v_field = 288, .v_calc = 576,
+ .v_offset = 0x18 /* 0 */ , .v_field = 288, .v_calc = 576,
.h_offset = 0x08, .h_pixels = 708, .h_calc = 709,
.v_max_out = 576, .h_max_out = 768,
}, {
.inputs = 1,
.audios = 1,
.capabilities = 0,
- .flags = SAA7146_EXT_SWAP_ODD_EVEN,
+ .flags = 0,
.stds = &standard[0],
.num_stds = sizeof(standard)/sizeof(struct saa7146_standard),
static struct saa7146_extension av7110_extension = {
.name = "dvb\0",
+ .flags = SAA7146_I2C_SHORT_DELAY,
.module = THIS_MODULE,
.pci_tbl = &pci_tbl[0],
MODULE_PARM_DESC(adac,"audio DAC type: 0 TI, 1 CRYSTAL, 2 MSP (use if autodetection fails)");
MODULE_PARM(hw_sections, "i");
MODULE_PARM_DESC(hw_sections, "0 use software section filter, 1 use hardware");
-
+MODULE_PARM(rgb_on, "i");
+MODULE_PARM_DESC(rgb_on, "For Siemens DVB-C cards only: Enable RGB control"
+ " signal on SCART pin 16 to switch SCART video mode from CVBS to RGB");
#include <linux/interrupt.h>
#include <linux/input.h>
+#if (LINUX_VERSION_CODE < KERNEL_VERSION(2,5,0))
+#include "input_fake.h"
+#endif
+
+
+
struct budget_ci {
struct budget budget;
struct input_dev input_dev;
struct tasklet_struct msp430_irq_tasklet;
};
-
-
-#ifndef BORROWED_FROM_AV7110_H_BUT_REALLY_BELONGS_IN_SAA7146_DEFS_H
-
-#define DEBINOSWAP 0x000e0000
-#define GPIO_IRQHI 0x10
-#define GPIO_INPUT 0x00
-
-void gpio_set(struct saa7146_dev* saa, u8 pin, u8 data)
-{
- u32 value = 0;
-
- /* sanity check */
- if(pin > 3)
- return;
-
- /* read old register contents */
- value = saa7146_read(saa, GPIO_CTRL );
-
- value &= ~(0xff << (8*pin));
- value |= (data << (8*pin));
-
- saa7146_write(saa, GPIO_CTRL, value);
-}
-
-
-
-static int wait_for_debi_done(struct saa7146_dev *saa)
-{
- int start = jiffies;
-
- /* wait for registers to be programmed */
- while (1) {
- if (saa7146_read(saa, MC2) & 2)
- break;
- if (jiffies - start > HZ / 20) {
- printk ("DVB (%s): timed out while waiting"
- " for registers getting programmed\n",
- __FUNCTION__);
- return -ETIMEDOUT;
- }
- }
-
- /* wait for transfer to complete */
- start = jiffies;
- while (1) {
- if (!(saa7146_read(saa, PSR) & SPCI_DEBI_S))
- break;
- saa7146_read(saa, MC2);
- if (jiffies - start > HZ / 4) {
- printk ("DVB (%s): timed out while waiting"
- " for transfer completion\n",
- __FUNCTION__);
- return -ETIMEDOUT;
- }
- }
-
- return 0;
-}
-
-
-static u32 debiread (struct saa7146_dev *saa, u32 config, int addr, int count)
+static u32 budget_debiread4 (struct saa7146_dev *saa, u32 config, int addr, int count)
{
u32 result = 0;
if (count > 4 || count <= 0)
return 0;
- if (wait_for_debi_done(saa) < 0)
+ if (saa7146_wait_for_debi_done(saa) < 0)
return 0;
saa7146_write (saa, DEBI_COMMAND,
saa7146_write(saa, DEBI_CONFIG, config);
saa7146_write(saa, MC2, (2 << 16) | 2);
- wait_for_debi_done(saa);
+ saa7146_wait_for_debi_done(saa);
result = saa7146_read(saa, DEBI_AD);
result &= (0xffffffffUL >> ((4 - count) * 8));
return result;
}
-
-
-/* DEBI during interrupt */
-static inline u32 irdebi(struct saa7146_dev *saa, u32 config, int addr, u32 val, int count)
-{
- u32 res;
- res = debiread(saa, config, addr, count);
- return res;
-}
-#endif
-
-
-
-
/* from reading the following remotes:
Zenith Universal 7 / TV Mode 807 / VCR Mode 837
Hauppauge (from NOVA-CI-s box product)
KEY_0, KEY_1, KEY_2, KEY_3, KEY_4, KEY_5, KEY_6, KEY_7, KEY_8,
KEY_9,
KEY_ENTER,
- 0,
+ KEY_RED,
KEY_POWER, /* RADIO on Hauppauge */
KEY_MUTE,
0,
0, 0, 0, 0, 0, 0, 0,
KEY_UP, KEY_DOWN,
KEY_OPTION, /* RESERVED on Hauppauge */
- 0,
+ KEY_BREAK,
/* 0x2X */
KEY_CHANNELUP, KEY_CHANNELDOWN,
KEY_PREVIOUS, /* Prev. Ch on Zenith, SOURCE on Hauppauge */
- 0, 0, 0,
+ 0, KEY_RESTART, KEY_OK,
KEY_CYCLEWINDOWS, /* MINIMIZE on Hauppauge */
0,
KEY_ENTER, /* VCR mode on Zenith */
KEY_MENU, /* FULL SCREEN on Hauppauge */
0,
/* 0x3X */
- 0,
+ KEY_SLOW,
KEY_PREVIOUS, /* VCR mode on Zenith */
KEY_REWIND,
0,
KEY_C,
0,
KEY_EXIT,
- 0,
+ KEY_POWER2,
KEY_TUNER, /* VCR mode on Zenith */
0,
};
struct budget_ci *budget_ci = (struct budget_ci*) data;
struct saa7146_dev *saa = budget_ci->budget.dev;
struct input_dev *dev = &budget_ci->input_dev;
- unsigned int code = irdebi(saa, DEBINOSWAP, 0x1234, 0, 2) >> 8;
+ unsigned int code = budget_debiread4(saa, DEBINOSWAP, 0x1234, 2) >> 8;
if (code & 0x40) {
code &= 0x3f;
saa7146_write(saa, IER, saa7146_read(saa, IER) | MASK_06);
- gpio_set(saa, 3, GPIO_IRQHI);
+ saa7146_setgpio(saa, 3, SAA7146_GPIO_IRQHI);
return 0;
}
struct input_dev *dev = &budget_ci->input_dev;
saa7146_write(saa, IER, saa7146_read(saa, IER) & ~MASK_06);
- gpio_set(saa, 3, GPIO_INPUT);
- gpio_set(saa, 2, GPIO_INPUT);
+ saa7146_setgpio(saa, 3, SAA7146_GPIO_INPUT);
+ saa7146_setgpio(saa, 2, SAA7146_GPIO_INPUT);
if (del_timer(&dev->timer))
input_event(dev, EV_KEY, key_map[dev->repeat_key], !!0);
projects / linux / commitdiff