When adding a VMCI resource, the check for an existing entry
would ignore that the new entry could be a wildcard. This could
result in multiple resource entries that would match a given
handle. One disastrous outcome of this is that the
refcounting used to ensure that delayed callbacks for VMCI
datagrams have run before the datagram is destroyed can be
wrong, since the refcount could be increased on the duplicate
entry. This in turn leads to a use after free bug. This issue
was discovered by Hangbin Liu using KASAN and syzkaller.
For TPM 1.2 chips the system setup utility allows to set the TPM device in
one of the following states:
* Active: Security chip is functional
* Inactive: Security chip is visible, but is not functional
* Disabled: Security chip is hidden and is not functional
When choosing the "Inactive" state, the TPM 1.2 device is enumerated and
registered, but sending TPM commands fail with either TPM_DEACTIVATED or
TPM_DISABLED depending if the firmware deactivated or disabled the TPM.
Since these TPM 1.2 error codes don't have special treatment, inactivating
the TPM leads to a very noisy kernel log buffer that shows messages like
the following:
tpm_tis 00:05: 1.2 TPM (device-id 0x0, rev-id 78)
tpm tpm0: A TPM error (6) occurred attempting to read a pcr value
tpm tpm0: TPM is disabled/deactivated (0x6)
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting to read a pcr value
ima: No TPM chip found, activating TPM-bypass! (rc=6)
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting get random
tpm tpm0: A TPM error (6) occurred attempting get random
Let's just suppress error log messages for the TPM_{DEACTIVATED,DISABLED}
return codes, since this is expected when the TPM 1.2 is set to Inactive.
In that case the kernel log is cleaner and less confusing for users, i.e:
IPCB should be cleared before icmp_send, since it may contain data from
previous layers and the data could be misinterpreted as ip header options,
which later caused the ihl to be set to an invalid value and resulted in
the following stack corruption:
[ 1083.031512] ib0: packet len 57824 (> 2048) too long to send, dropping
[ 1083.031843] ib0: packet len 37904 (> 2048) too long to send, dropping
[ 1083.032004] ib0: packet len 4040 (> 2048) too long to send, dropping
[ 1083.032253] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.032481] ib0: packet len 23960 (> 2048) too long to send, dropping
[ 1083.033149] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.033439] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.033700] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.034124] ib0: packet len 63800 (> 2048) too long to send, dropping
[ 1083.034387] ==================================================================
[ 1083.034602] BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0xf08/0x1310
[ 1083.034798] Write of size 4 at addr ffff880353457c5f by task kworker/u16:0/7
[ 1083.034990]
[ 1083.035104] CPU: 7 PID: 7 Comm: kworker/u16:0 Tainted: G O 4.19.0-rc5+ #1
[ 1083.035316] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu2 04/01/2014
[ 1083.035573] Workqueue: ipoib_wq ipoib_cm_skb_reap [ib_ipoib]
[ 1083.035750] Call Trace:
[ 1083.035888] dump_stack+0x9a/0xeb
[ 1083.036031] print_address_description+0xe3/0x2e0
[ 1083.036213] kasan_report+0x18a/0x2e0
[ 1083.036356] ? __ip_options_echo+0xf08/0x1310
[ 1083.036522] __ip_options_echo+0xf08/0x1310
[ 1083.036688] icmp_send+0x7b9/0x1cd0
[ 1083.036843] ? icmp_route_lookup.constprop.9+0x1070/0x1070
[ 1083.037018] ? netif_schedule_queue+0x5/0x200
[ 1083.037180] ? debug_show_all_locks+0x310/0x310
[ 1083.037341] ? rcu_dynticks_curr_cpu_in_eqs+0x85/0x120
[ 1083.037519] ? debug_locks_off+0x11/0x80
[ 1083.037673] ? debug_check_no_obj_freed+0x207/0x4c6
[ 1083.037841] ? check_flags.part.27+0x450/0x450
[ 1083.037995] ? debug_check_no_obj_freed+0xc3/0x4c6
[ 1083.038169] ? debug_locks_off+0x11/0x80
[ 1083.038318] ? skb_dequeue+0x10e/0x1a0
[ 1083.038476] ? ipoib_cm_skb_reap+0x2b5/0x650 [ib_ipoib]
[ 1083.038642] ? netif_schedule_queue+0xa8/0x200
[ 1083.038820] ? ipoib_cm_skb_reap+0x544/0x650 [ib_ipoib]
[ 1083.038996] ipoib_cm_skb_reap+0x544/0x650 [ib_ipoib]
[ 1083.039174] process_one_work+0x912/0x1830
[ 1083.039336] ? wq_pool_ids_show+0x310/0x310
[ 1083.039491] ? lock_acquire+0x145/0x3a0
[ 1083.042312] worker_thread+0x87/0xbb0
[ 1083.045099] ? process_one_work+0x1830/0x1830
[ 1083.047865] kthread+0x322/0x3e0
[ 1083.050624] ? kthread_create_worker_on_cpu+0xc0/0xc0
[ 1083.053354] ret_from_fork+0x3a/0x50
For instance __ip_options_echo is failing to proceed with invalid srr and
optlen passed from another layer via IPCB
If the provider driver (such as rdma_rxe) doesn't support pma counters,
avoid exposing its directory similar to optional hw_counters directory.
If core fails to read the PMA counter, return an error so that user can
retry later if needed.
In megasas_mgmt_compat_ioctl_fw(), to handle the structure
compat_megasas_iocpacket 'cioc', a user-space structure megasas_iocpacket
'ioc' is allocated before megasas_mgmt_ioctl_fw() is invoked to handle
the packet. Since the two data structures have different fields, the data
is copied from 'cioc' to 'ioc' field by field. In the copy process,
'sense_ptr' is prepared if the field 'sense_len' is not null, because it
will be used in megasas_mgmt_ioctl_fw(). To prepare 'sense_ptr', the
user-space data 'ioc->sense_off' and 'cioc->sense_off' are copied and
saved to kernel-space variables 'local_sense_off' and 'user_sense_off'
respectively. Given that 'ioc->sense_off' is also copied from
'cioc->sense_off', 'local_sense_off' and 'user_sense_off' should have the
same value. However, 'cioc' is in the user space and a malicious user can
race to change the value of 'cioc->sense_off' after it is copied to
'ioc->sense_off' but before it is copied to 'user_sense_off'. By doing
so, the attacker can inject different values into 'local_sense_off' and
'user_sense_off'. This can cause undefined behavior in the following
execution, because the two variables are supposed to be same.
This patch enforces a check on the two kernel variables 'local_sense_off'
and 'user_sense_off' to make sure they are the same after the copy. In
case they are not, an error code EINVAL will be returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a target disconnects during a PIO data transfer the command may fail
when the target reconnects:
scsi host1: DMA length is zero!
scsi host1: cur adr[04380000] len[00000000]
The scsi bus is then reset. This happens because the residual reached
zero before the transfer was completed.
The usual residual calculation relies on the Transfer Count registers.
That works for DMA transfers but not for PIO transfers. Fix the problem
by storing the PIO transfer residual and using that to correctly
calculate bytes_sent.
Fixes: 6fe07aaffbf0 ("[SCSI] m68k: new mac_esp scsi driver") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a cgroup has many tasks with many open file descriptors then we would
end up in a large loop without any rescheduling point throught the
operation. Add cond_resched once per task.
When running in AP mode, ath10k sometimes suffers from TX credit
starvation. The issue is hard to reproduce and shows up once in a
few days, but has been repeatedly seen with QCA9882 and a large
range of firmwares, including 10.2.4.70.67.
Once the module is in this state, TX credits are never replenished,
which results in "SWBA overrun" errors, as no beacons can be sent.
Even worse, WMI commands run in a timeout while holding the conf
mutex for three seconds each, making any further operations slow
and the whole system unresponsive.
The firmware/driver never recovers from that state automatically,
and triggering TX flush or warm restarts won't work over WMI. So
issue a hardware restart if a WMI command times out due to missing
TX credits. This implies a connectivity outage of about 1.4s in AP
mode, but brings back the interface and the whole system to a usable
state. WMI command timeouts have not been seen in absent of this
specific issue, so taking such drastic actions seems legitimate.
Signed-off-by: Martin Willi <martin@strongswan.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While VF2VF with RSS communication, RSS Type were wrongly recognized
and RSS hash was not calculated as it should be. Packets was
distributed on various queues by accident.
This commit fixes that behaviour and causes proper RSS Type recognition.
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you look at "pinconf-groups" in debugfs for ssbi-gpio you'll notice
it looks like nonsense.
The problem is fairly well described in commit 1cf86bc21257 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit 05e0c828955c ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-gpio has the same
problem. Let's fix it there too.
Fixes: b4c45fe974bc ("pinctrl: qcom: ssbi: Family A gpio & mpp drivers") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you look at "pinconf-groups" in debugfs for ssbi-mpp you'll notice
it looks like nonsense.
The problem is fairly well described in commit 1cf86bc21257 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit 05e0c828955c ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-mpp has the same
problem. Let's fix it there too.
NOTE: in case it's helpful to someone reading this, the way to tell
whether to do the -EINVAL or not is to look at the PCONFDUMP for a
given attribute. If the last element (has_arg) is false then you need
to do the -EINVAL trick.
ALSO NOTE: it seems unlikely that the values returned when we try to
get PIN_CONFIG_BIAS_PULL_UP will actually be printed since "has_arg"
is false for that one, but I guess it's still fine to return different
values so I kept doing that. It seems like another driver (ssbi-gpio)
uses a custom attribute (PM8XXX_QCOM_PULL_UP_STRENGTH) for something
similar so maybe a future change should do that here too.
It looks like we parse the drive strength setting here, but never
actually write it into the hardware to update it. Parse the setting and
then write it at the end of the pinconf setting function so that it
actually sticks in the hardware.
Fixes: 0e948042c420 ("pinctrl: qcom: spmi-mpp: Implement support for sink mode") Cc: Doug Anderson <dianders@chromium.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bay and Cherry Trail DSTDs represent a different set of devices depending
on which OS the device think it is booting. One set of decices for Windows
and another set of devices for Android which targets the Android-x86 Linux
kernel fork (which e.g. used to have its own display driver instead of
using the i915 driver).
Which set of devices we are actually going to get is out of our control,
this is controlled by the ACPI OSID variable, which gets either set through
an EFI setup option, or sometimes is autodetected. So we need to support
both.
This commit adds support for the 80862286 and 808622C0 ACPI HIDs which we
get for the first resp. second DMA controller on Cherry Trail devices when
OSID is set to Android.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently align the end of the compressed image to a multiple of
16. However, the PE-COFF header included in the EFI stub says that
the file alignment is 32 bytes, and when adding an EFI signature to
the file it must first be padded to this alignment.
sbsigntool commands warn about this:
warning: file-aligned section .text extends beyond end of file
warning: checksum areas are greater than image size. Invalid section table?
Worse, pesign -at least when creating a detached signature- uses the
hash of the unpadded file, resulting in an invalid signature if
padding is required.
Avoid both these problems by increasing alignment to 32 bytes when
CONFIG_EFI_STUB is enabled.
This patch adds the device ID for the AMPAK AP6335 combo module used
in the 1st generation WeTek Hub Android/LibreELEC HTPC box. The WiFI
chip identifies itself as BCM4339, while Bluetooth identifies itself
as BCM4335 (rev C0):
We can not call dev_pm_opp_of_cpumask_remove_table() freely anymore
since the latest OPP core updates as that uses reference counting to
free resources. There are cases where no static OPPs are added (using
DT) for a platform and trying to remove the OPP table may end up
decrementing refcount which is already zero and hence generating
warnings.
Lets track if we were able to add static OPPs or not and then only
remove the table based on that. Some reshuffling of code is also done to
do that.
On OLPC XO-1, the RTC is discovered via device tree from the arch
initcall. Don't let the PC platform register another one from its device
initcall, it's not going to work:
sysfs: cannot create duplicate filename '/devices/platform/rtc_cmos'
CPU: 0 PID: 1 Comm: swapper Not tainted 4.19.0-rc6 #12
Hardware name: OLPC XO/XO, BIOS OLPC Ver 1.00.01 06/11/2014
Call Trace:
dump_stack+0x16/0x18
sysfs_warn_dup+0x46/0x58
sysfs_create_dir_ns+0x76/0x9b
kobject_add_internal+0xed/0x209
? __schedule+0x3fa/0x447
kobject_add+0x5b/0x66
device_add+0x298/0x535
? insert_resource_conflict+0x2a/0x3e
platform_device_add+0x14d/0x192
? io_delay_init+0x19/0x19
platform_device_register+0x1c/0x1f
add_rtc_cmos+0x16/0x31
do_one_initcall+0x78/0x14a
? do_early_param+0x75/0x75
kernel_init_freeable+0x152/0x1e0
? rest_init+0xa2/0xa2
kernel_init+0x8/0xd5
ret_from_fork+0x2e/0x38
kobject_add_internal failed for rtc_cmos with -EEXIST, don't try to
register things with the same name in the same directory.
platform rtc_cmos: registered platform RTC device (no PNP device found)
If all free RB queues are empty, the driver will never restock the
free RB queue. That's because the restocking happens in the Rx flow,
and if the free queue is empty there will be no Rx.
Although there's a background worker (a.k.a. allocator) allocating
memory for RBs so that the Rx handler can restock them, the worker may
run only after the free queue has become empty (and then it is too
late for restocking as explained above).
There is a solution for that called 'emergency': If the number of used
RB's reaches half the amount of all RB's, the Rx handler will not wait
for the allocator but immediately allocate memory for the used RB's
and restock the free queue.
But, since the used RB's is per queue, it may happen that the used
RB's are spread between the queues such that the emergency check will
fail for each of the queues
(and still run out of RBs, causing the above symptom).
To fix it, move to emergency mode if the sum of *all* used RBs (for
all Rx queues) reaches half the amount of all RB's
This device reports SDHCI_CLOCK_INT_STABLE even though it's not
ready to take SDHCI_CLOCK_CARD_EN. The symptom is that reading
SDHCI_CLOCK_CONTROL after enabling the clock shows absence of the
bit from the register (e.g. expecting 0x0000fa07 = 0x0000fa03 |
SDHCI_CLOCK_CARD_EN but only observed the first operand).
For each system in a given pevent, read_event_files() reads in a
temporary 'sys' string. Be sure to free this string before moving onto
to the next system and/or leaving read_event_files().
Fixes the following coverity complaints:
Error: RESOURCE_LEAK (CWE-772):
tools/perf/util/trace-event-read.c:343: overwrite_var: Overwriting
"sys" in "sys = read_string()" leaks the storage that "sys" points to.
tools/perf/util/trace-event-read.c:353: leaked_storage: Variable "sys"
going out of scope leaks the storage it points to.
Signed-off-by: Sanskriti Sharma <sansharm@redhat.com> Reviewed-by: Jiri Olsa <jolsa@kernel.org> Cc: Joe Lawrence <joe.lawrence@redhat.com> Link: http://lkml.kernel.org/r/1538490554-8161-6-git-send-email-sansharm@redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Technically this is not required because disabling the PWM should be
enough. However, when support for atomic operations was implemented in
the PWM subsystem, only actual changes to the PWM channel are applied
during pwm_config(), which means that during after resume from suspend
the old settings won't be applied.
One possible solution is for the PWM driver to implement its own PM
operations such that settings from before suspend get applied on resume.
This has the disadvantage of completely ignoring any particular ordering
requirements that PWM user drivers might have, so it is best to leave it
up to the user drivers to apply the settings that they want at the
appropriate time.
Another way to solve this would be to read back the current state of the
PWM at the time of resume. That way, in case the configuration was lost
during suspend, applying the old settings in PWM user drivers would
actually get them applied because they differ from the current settings.
However, not all PWM drivers support reading the hardware state, and not
all hardware may support it.
The best workaround at this point seems to be to let PWM user drivers
tell the PWM subsystem that the PWM is turned off by, in addition to
disabling it, also setting the duty cycle to 0. This causes the resume
operation to apply a configuration that is different from the current
configuration, resulting in the proper state from before suspend getting
restored.
When running as a level 3 guest with no host provided sthyi support
sclp_ocf_cpc_name_copy() will only return zeroes. Zeroes are not a
valid group name, so let's not indicate that the group name field is
valid.
Also the group name is not dependent on stsi, let's not return based
on stsi before setting it.
Configuring generic network device parameters on tun will fail in
presence of IFLA_INFO_KIND attribute in IFLA_LINKINFO nested attribute
since tun_validate() always return failure.
This can be visualized with following ip-link(8) command sequences:
# ip link set dev tun0 group 100
# ip link set dev tun0 group 100 type tun
RTNETLINK answers: Invalid argument
with contrast to dummy and veth drivers:
# ip link set dev dummy0 group 100
# ip link set dev dummy0 type dummy
# ip link set dev veth0 group 100
# ip link set dev veth0 group 100 type veth
Fix by returning zero in tun_validate() when @data is NULL that is
always in case since rtnl_link_ops->maxtype is zero in tun driver.
Fixes: f019a7a594d9 ("tun: Implement ip link del tunXXX") Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we fail to allocate the request queue for a disk, we still need to
free that disk, not just the previous ones. Additionally, we need to
cleanup the previous request queues.
Move queue allocation next to disk allocation to fix a couple of issues:
- If add_disk() hasn't been called, we should clear disk->queue before
calling put_disk().
- If we fail to allocate a request queue, we still need to put all of
the disks, not just the ones that we allocated queues for.
It was found that when debug_locks was turned off because of a problem
found by the lockdep code, the system performance could drop quite
significantly when the lock_stat code was also configured into the
kernel. For instance, parallel kernel build time on a 4-socket x86-64
server nearly doubled.
Further analysis into the cause of the slowdown traced back to the
frequent call to debug_locks_off() from the __lock_acquired() function
probably due to some inconsistent lockdep states with debug_locks
off. The debug_locks_off() function did an unconditional atomic xchg
to write a 0 value into debug_locks which had already been set to 0.
This led to severe cacheline contention in the cacheline that held
debug_locks. As debug_locks is being referenced in quite a few different
places in the kernel, this greatly slow down the system performance.
To prevent that trashing of debug_locks cacheline, lock_acquired()
and lock_contended() now checks the state of debug_locks before
proceeding. The debug_locks_off() function is also modified to check
debug_locks before calling __debug_locks_off().
Signed-off-by: Waiman Long <longman@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Link: http://lkml.kernel.org/r/1539913518-15598-1-git-send-email-longman@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/net/ethernet/qlogic/qla3xxx.c:384:24: warning: signed shift
result (0xF00000000) requires 37 bits to represent, but 'int' only has
32 bits [-Wshift-overflow]
((ISP_NVRAM_MASK << 16) | qdev->eeprom_cmd_data));
~~~~~~~~~~~~~~ ^ ~~
1 warning generated.
The warning is certainly accurate since ISP_NVRAM_MASK is defined as
(0x000F << 16) which is then shifted by 16, resulting in 64424509440,
well above UINT_MAX.
Given that this is the only location in this driver where ISP_NVRAM_MASK
is shifted again, it seems likely that ISP_NVRAM_MASK was originally
defined without a shift and during the move of the shift to the
definition, this statement wasn't properly removed (since ISP_NVRAM_MASK
is used in the statenent right above this). Only the maintainers can
confirm this since this statment has been here since the driver was
first added to the kernel.
Link: https://github.com/ClangBuiltLinux/linux/issues/127 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The size of the resulting cpu map can be smaller than a multiple of
sizeof(u64), resulting in SIGBUS on cpus like Sparc as the next event
will not be aligned properly.
Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@intel.com> Fixes: 6c872901af07 ("perf cpu_map: Add cpu_map event synthesize function") Link: http://lkml.kernel.org/r/20181011.224655.716771175766946817.davem@davemloft.net Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So that when it is unset, ie. '-1', userspace can see it
properly.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is important to clear the hw->state value for non-stopped events
when they are added into the PMU. Otherwise when the event is
scheduled out, we won't read the counter because HES_UPTODATE is still
set. This breaks 'perf stat' and similar use cases, causing all the
events to show zero.
This worked for multi-pcr because we make explicit sparc_pmu_start()
calls in calculate_multiple_pcrs(). calculate_single_pcr() doesn't do
this because the idea there is to accumulate all of the counter
settings into the single pcr value. So we have to add explicit
hw->state handling there.
Like x86, we use the PERF_HES_ARCH bit to track truly stopped events
so that we don't accidently start them on a reload.
Related to all of this, sparc_pmu_start() is missing a userpage update
so add it.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael reported an issue with oversized terms values assignment
and I noticed there was actually a misunderstanding of the max
value check in the past.
The above commit's changelog says:
If bit 21 is set, there is parsing issues as below.
$ perf stat -a -e uncore_qpi_0/event=0x200002,umask=0x8/
event syntax error: '..pi_0/event=0x200002,umask=0x8/'
\___ value too big for format, maximum is 511
But there's no issue there, because the event value is distributed
along the value defined by the format. Even if the format defines
separated bit, the value is treated as a continual number, which
should follow the format definition.
In above case it's 9-bit value with last bit separated:
$ cat uncore_qpi_0/format/event
config:0-7,21
Hence the value 0x200002 is correctly reported as format violation,
because it exceeds 9 bits. It should have been 0x102 instead, which
sets the 9th bit - the bit 21 of the format.
$ perf stat -vv -a -e uncore_qpi_0/event=0x102,umask=0x8/
Using CPUID GenuineIntel-6-2D
...
------------------------------------------------------------
perf_event_attr:
type 10
size 112
config 0x200802
sample_type IDENTIFIER
...
Reported-by: Michael Petlan <mpetlan@redhat.com> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: ac0e2cd55537 ("perf tools: Fix PMU term format max value calculation") Link: http://lkml.kernel.org/r/20181003072046.29276-1-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Future Intel processors will support "Enhanced IBRS" which is an "always
on" mode i.e. IBRS bit in SPEC_CTRL MSR is enabled once and never
disabled.
From the specification [1]:
"With enhanced IBRS, the predicted targets of indirect branches
executed cannot be controlled by software that was executed in a less
privileged predictor mode or on another logical processor. As a
result, software operating on a processor with enhanced IBRS need not
use WRMSR to set IA32_SPEC_CTRL.IBRS after every transition to a more
privileged predictor mode. Software can isolate predictor modes
effectively simply by setting the bit once. Software need not disable
enhanced IBRS prior to entering a sleep state such as MWAIT or HLT."
If Enhanced IBRS is supported by the processor then use it as the
preferred spectre v2 mitigation mechanism instead of Retpoline. Intel's
Retpoline white paper [2] states:
"Retpoline is known to be an effective branch target injection (Spectre
variant 2) mitigation on Intel processors belonging to family 6
(enumerated by the CPUID instruction) that do not have support for
enhanced IBRS. On processors that support enhanced IBRS, it should be
used for mitigation instead of retpoline."
The reason why Enhanced IBRS is the recommended mitigation on processors
which support it is that these processors also support CET which
provides a defense against ROP attacks. Retpoline is very similar to ROP
techniques and might trigger false positives in the CET defense.
If Enhanced IBRS is selected as the mitigation technique for spectre v2,
the IBRS bit in SPEC_CTRL MSR is set once at boot time and never
cleared. Kernel also has to make sure that IBRS bit remains set after
VMEXIT because the guest might have cleared the bit. This is already
covered by the existing x86_spec_ctrl_set_guest() and
x86_spec_ctrl_restore_host() speculation control functions.
Enhanced IBRS still requires IBPB for full mitigation.
[1] Speculative-Execution-Side-Channel-Mitigations.pdf
[2] Retpoline-A-Branch-Target-Injection-Mitigation.pdf
Both documents are available at:
https://bugzilla.kernel.org/show_bug.cgi?id=199511
Originally-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Tim C Chen <tim.c.chen@intel.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Ravi Shankar <ravi.v.shankar@intel.com> Link: https://lkml.kernel.org/r/1533148945-24095-1-git-send-email-sai.praneeth.prakhya@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
memory_corruption_check[{_period|_size}]()'s handlers do not check input
argument before passing it to kstrtoul() or simple_strtoull(). The argument
would be a NULL pointer if each of the kernel parameters, without its
value, is set in command line and thus cause the following panic.
STIBP is a feature provided by certain Intel ucodes / CPUs. This feature
(once enabled) prevents cross-hyperthread control of decisions made by
indirect branch predictors.
Enable this feature if
- the CPU is vulnerable to spectre v2
- the CPU supports SMT and has SMT siblings online
- spectre_v2 mitigation autoselection is enabled (default)
After some previous discussion, this leaves STIBP on all the time, as wrmsr
on crossing kernel boundary is a no-no. This could perhaps later be a bit
more optimized (like disabling it in NOHZ, experiment with disabling it in
idle, etc) if needed.
Note that the synchronization of the mask manipulation via newly added
spec_ctrl_mutex is currently not strictly needed, as the only updater is
already being serialized by cpu_add_remove_lock, but let's make this a
little bit more future-proof.
The Creative Audigy SE (SB0570) card currently exhibits an audible pop
whenever playback is stopped or resumed, or during silent periods of an
audio stream. Initialise the IZD bit to the 0 to eliminate these pops.
The Infinite Zero Detection (IZD) feature on the DAC causes the output
to be shunted to Vcap after 2048 samples of silence. This discharges the
AC coupling capacitor through the output and causes the aforementioned
pop/click noise.
The behaviour of the IZD bit is described on page 15 of the WM8768GEDS
datasheet: "With IZD=1, applying MUTE for 1024 consecutive input samples
will cause all outputs to be connected directly to VCAP. This also
happens if 2048 consecutive zero input samples are applied to all 6
channels, and IZD=0. It will be removed as soon as any channel receives
a non-zero input". I believe the second sentence might be referring to
IZD=1 instead of IZD=0 given the observed behaviour of the card.
This change should make the DAC initialisation consistent with
Creative's Windows driver, as this popping persists when initialising
the card in Linux and soft rebooting into Windows, but is not present on
a cold boot to Windows.
BIOS on ASUS G751 doesn't seem to map the headphone pin (NID 0x16)
correctly. Add a quirk to address it, as well as chaining to the
previous fix for the microphone.
Fix a long-existing small nasty bug in the map_pages() implementation which
leads to overwriting already written pte entries with zero, *if* map_pages() is
called a second time with an end address which isn't aligned on a pmd boundry.
This happens for example if we want to remap only the text segment read/write
in order to run alternative patching on the code. Exiting the loop when we
reach the end address fixes this.
Helge noticed that the address of the os_hpmc handler was not being
correctly calculated in the hpmc macro. As a result, PDCE_CHECK would
fail to call os_hpmc:
Currently, "disable_clkrun" yenta_socket module parameter is only
implemented for TI CardBus bridges.
Add also an implementation for Ricoh bridges that have the necessary
setting documented in publicly available datasheets.
Tested on a RL5C476II with a Sunrich C-160 CardBus NIC that doesn't work
correctly unless the CLKRUN protocol is disabled.
Let's also make it clear in its description that the "disable_clkrun"
module parameter only works on these two previously mentioned brands of
CardBus bridges.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Cc: stable@vger.kernel.org Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an invalid mount option is passed to jffs2, jffs2_parse_options()
will fail and jffs2_sb_info will be freed, but then jffs2_sb_info will
be used (use-after-free) and freeed (double-free) in jffs2_kill_sb().
Fix it by removing the buggy invocation of kfree() when getting invalid
mount options.
Fixes: 92abc475d8de ("jffs2: implement mount option parsing and compression overriding") Cc: stable@kernel.org Signed-off-by: Hou Tao <houtao1@huawei.com> Reviewed-by: Richard Weinberger <richard@nod.at> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices with compatible="pmbus" field have zero initial page count,
and pmbus_clear_faults() being called before the page count auto-
detection does not actually clear faults because it depends on the
page count. Non-cleared faults in its turn may fail the subsequent
page count auto-detection.
This patch fixes this problem by calling pmbus_clear_fault_page()
for currently set page and calling pmbus_clear_faults() after the
page count was detected.
refill->end record the last key of writeback, for example, at the first
time, keys (1,128K) to (1,1024K) are flush to the backend device, but
the end key (1,1024K) is not included, since the bellow code:
if (bkey_cmp(k, refill->end) >= 0) {
ret = MAP_DONE;
goto out;
}
And in the next time when we refill writeback keybuf again, we searched
key start from (1,1024K), and got a key bigger than it, so the key
(1,1024K) missed.
This patch modify the above code, and let the end key to be included to
the writeback key buffer.
The posix timer overrun handling is broken because the forwarding functions
can return a huge number of overruns which does not fit in an int. As a
consequence timer_getoverrun(2) and siginfo::si_overrun can turn into
random number generators.
The k_clock::timer_forward() callbacks return a 64 bit value now. Make
k_itimer::ti_overrun[_last] 64bit as well, so the kernel internal
accounting is correct. 3Remove the temporary (int) casts.
Add a helper function which clamps the overrun value returned to user space
via timer_getoverrun(2) or siginfo::si_overrun limited to a positive value
between 0 and INT_MAX. INT_MAX is an indicator for user space that the
overrun value has been clamped.
Reported-by: Team OWL337 <icytxw@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: John Stultz <john.stultz@linaro.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Link: https://lkml.kernel.org/r/20180626132705.018623573@linutronix.de
[florian: Make patch apply to v4.9.135] Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch moves fs_timeout() actions into an async worker.
Fixes: commit 48257c4f168e5 ("Add fs_enet ethernet network driver, for several embedded platforms") Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns that the declaration of jiffies in include/linux/jiffies.h
doesn't match the definition in arch/x86/time/kernel.c:
arch/x86/kernel/time.c:29:42: warning: section does not match previous declaration [-Wsection]
__visible volatile unsigned long jiffies __cacheline_aligned = INITIAL_JIFFIES;
^
./include/linux/cache.h:49:4: note: expanded from macro '__cacheline_aligned'
__section__(".data..cacheline_aligned")))
^
./include/linux/jiffies.h:81:31: note: previous attribute is here
extern unsigned long volatile __cacheline_aligned_in_smp __jiffy_arch_data jiffies;
^
./arch/x86/include/asm/cache.h:20:2: note: expanded from macro '__cacheline_aligned_in_smp'
__page_aligned_data
^
./include/linux/linkage.h:39:29: note: expanded from macro '__page_aligned_data'
#define __page_aligned_data __section(.data..page_aligned) __aligned(PAGE_SIZE)
^
./include/linux/compiler_attributes.h:233:56: note: expanded from macro '__section'
#define __section(S) __attribute__((__section__(#S)))
^
1 warning generated.
The declaration was changed in commit 7c30f352c852 ("jiffies.h: declare
jiffies and jiffies_64 with ____cacheline_aligned_in_smp") but wasn't
updated here. Make them match so Clang no longer warns.
Fixes: 7c30f352c852 ("jiffies.h: declare jiffies and jiffies_64 with ____cacheline_aligned_in_smp") Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20181013005311.28617-1-natechancellor@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric reported that a sequence count loop using this_cpu_read() got
optimized out. This is wrong, this_cpu_read() must imply READ_ONCE()
because the interface is IRQ-safe, therefore an interrupt can have
changed the per-cpu value.
Fixes: 7c3576d261ce ("[PATCH] i386: Convert PDA into the percpu section") Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Eric Dumazet <edumazet@google.com> Cc: hpa@zytor.com Cc: eric.dumazet@gmail.com Cc: bp@alien8.de Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20181011104019.748208519@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a very low cpu.cfs_quota_us setting, such as the minimum of 1000,
distribute_cfs_runtime may not empty the throttled_list before it runs
out of runtime to distribute. In that case, due to the change from c06f04c7048 to put throttled entries at the head of the list, later entries
on the list will starve. Essentially, the same X processes will get pulled
off the list, given CPU time and then, when expired, get put back on the
head of the list where distribute_cfs_runtime will give runtime to the same
set of processes leaving the rest.
Fix the issue by setting a bit in struct cfs_bandwidth when
distribute_cfs_runtime is running, so that the code in throttle_cfs_rq can
decide to put the throttled entry on the tail or the head of the list. The
bit is set/cleared by the callers of distribute_cfs_runtime while they hold
cfs_bandwidth->lock.
This is easy to reproduce with a handful of CPU consumers. I use 'crash' on
the live system. In some cases you can simply look at the throttled list and
see the later entries are not changing:
Commit 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more") checks the
transfer flags for URBs submitted from userspace via usbfs. However,
the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be
allowed for a control transfer was added in the wrong place, before
the code has properly determined the direction of the control
transfer. (Control transfers are special because for them, the
direction is set by the bRequestType byte of the Setup packet rather
than direction bit of the endpoint address.)
This patch moves code which sets up the allow_short flag for control
transfers down after is_in has been set to the correct value.
Fix this by sanitizing num before using it to index
fsg_opts->common->luns
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
The usb standard ("Universal Serial Bus Class Definitions for Communication
Devices") distiguishes between "consistent signals" (DSR, DCD), and
"irregular signals" (break, ring, parity error, framing error, overrun).
The bits of "irregular signals" are set, if this error/event occurred on
the device side and are immeadeatly unset, if the serial state notification
was sent.
Like other drivers of real serial ports do, just the occurence of those
events should be counted in serial_icounter_struct (but no 1->0
transitions).
Fix this by sanitizing hdr.cmd before using it to index
ucm_cmd_table.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Fix this by sanitizing hdr.cmd before using it to index
ucm_cmd_table.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Fix this by sanitizing pin_index before using it to index
ops->pin_config, and before passing it as an argument to
function ptp_set_pinfunc(), in which it is used to index
info->pin_config.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the victim might've been rmdir'ed just before the lock_rename();
unlike the normal callers, we do not look the source up after the
parents are locked - we know it beforehand and just recheck that it's
still the child of what used to be its parent. Unfortunately,
the check is too weak - we don't spot a dead directory since its
->d_parent is unchanged, dentry is positive, etc. So we sail all
the way to ->rename(), with hosting filesystems _not_ expecting
to be asked renaming an rmdir'ed subdirectory.
The fix is easy, fortunately - the lock on parent is sufficient for
making IS_DEADDIR() on child safe.
Cc: stable@vger.kernel.org Fixes: 9ae326a69004 (CacheFiles: A cache that backs onto a mounted filesystem) Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The truncate transaction does not ever modify the inode btree, but
includes an associated log reservation. Update
xfs_calc_itruncate_reservation() to remove the reservation
associated with inobt updates.
[Amir: This commit was merged for kernel v4.16 and a twin commit was
merged for xfsprogs v4.16. As a result, a small xfs filesystem
formatted with features -m rmapbt=1,reflink=1 using mkfs.xfs
version >= v4.16 cannot be mounted with kernel < v4.16.
For example, xfstests generic/17{1,2,3} format a small fs and
when trying to mount it, they fail with an assert on this very
demonic line:
The simple solution for stable kernels is to apply this patch,
because mkfs.xfs v4.16 is already in the wild, so we have to
assume that xfs filesystems with a "too small" log exist.
Regardless, xfsprogs maintainers should also consider reverting
the twin patch to stop creating those filesystems for the sake
of users with unpatched kernels.]
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Cc: <stable@vger.kernel.org> # v4.9+ Signed-off-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Darrick J . Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MXS driver was calling back into the GPIO API from
its irqchip. This is not very elegant, as we are a driver,
let's just shortcut back into the gpio_chip .get() function
instead.
This is a tricky case since the .get() callback is not in
this file, instead assigned by bgpio_init(). Calling the
function direcly in the gpio_chip is however the lesser
evil.
ahci_pci_reset_controller() calls ahci_reset_controller(), which may
fail, but ignores the result code and always returns success. This
may result in failures like below
ahci 0000:02:00.0: version 3.0
ahci 0000:02:00.0: enabling device (0000 -> 0003)
ahci 0000:02:00.0: SSS flag set, parallel bus scan disabled
ahci 0000:02:00.0: controller reset failed (0xffffffff)
ahci 0000:02:00.0: failed to stop engine (-5)
... repeated many times ...
ahci 0000:02:00.0: failed to stop engine (-5)
Unable to handle kernel paging request at virtual address ffff0000093f9018
...
PC is at ahci_stop_engine+0x5c/0xd8 [libahci]
LR is at ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
...
[<ffff000000a17014>] ahci_stop_engine+0x5c/0xd8 [libahci]
[<ffff000000a196b4>] ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
[<ffff000000a197d8>] ahci_init_controller+0x80/0x168 [libahci]
[<ffff000000a260f8>] ahci_pci_init_controller+0x60/0x68 [ahci]
[<ffff000000a26f94>] ahci_init_one+0x75c/0xd88 [ahci]
[<ffff000008430324>] local_pci_probe+0x3c/0xb8
[<ffff000008431728>] pci_device_probe+0x138/0x170
[<ffff000008585e54>] driver_probe_device+0x2dc/0x458
[<ffff0000085860e4>] __driver_attach+0x114/0x118
[<ffff000008583ca8>] bus_for_each_dev+0x60/0xa0
[<ffff000008585638>] driver_attach+0x20/0x28
[<ffff0000085850b0>] bus_add_driver+0x1f0/0x2a8
[<ffff000008586ae0>] driver_register+0x60/0xf8
[<ffff00000842f9b4>] __pci_register_driver+0x3c/0x48
[<ffff000000a3001c>] ahci_pci_driver_init+0x1c/0x1000 [ahci]
[<ffff000008083918>] do_one_initcall+0x38/0x120
where an obvious hardware level failure results in an unnecessary 15 second
delay and a subsequent crash.
So record the result code of ahci_reset_controller() and relay it, rather
than ignoring it.
The SCTP program may sleep under a spinlock, and the function call path is:
sctp_generate_t3_rtx_event (acquire the spinlock)
sctp_do_sm
sctp_side_effects
sctp_cmd_interpreter
sctp_make_init_ack
sctp_pack_cookie
crypto_shash_setkey
shash_setkey_unaligned
kmalloc(GFP_KERNEL)
For the same reason, the orinoco driver may sleep in interrupt handler,
and the function call path is:
orinoco_rx_isr_tasklet
orinoco_rx
orinoco_mic
crypto_shash_setkey
shash_setkey_unaligned
kmalloc(GFP_KERNEL)
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool and my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
This backport is incorrect. The part that updated __startup_64() in
arch/x86/kernel/head64.c was dropped, presumably because that function
doesn't exist in 4.9. However that seems to be an essential of the
fix. In 4.9 the startup_64 routine in arch/x86/kernel/head_64.S would
need to be changed instead.
I also found that this introduces new boot-time warnings on some
systems if CONFIG_DEBUG_WX is enabled.
So, unless someone provides fixes for those issues, I think this should
be reverted for the 4.9 branch.
Commit 058214a4d1df ("ip6_tun: Add infrastructure for doing
encapsulation") added the ip6_tnl_encap() call in ip6_tnl_xmit(), before
the call to ipv6_push_frag_opts() to append the IPv6 Tunnel Encapsulation
Limit option (option 4, RFC 2473, par. 5.1) to the outer IPv6 header.
As long as the option didn't actually end up in generated packets, this
wasn't an issue. Then commit 89a23c8b528b ("ip6_tunnel: Fix missing tunnel
encapsulation limit option") fixed sending of this option, and the
resulting layout, e.g. for FoU, is:
Needless to say, FoU and GUE (at least) won't work over IPv6. The option
is appended by default, and I couldn't find a way to disable it with the
current iproute2.
When an FDB entry is configured, the address is validated to have the
length of an Ethernet address, but the device for which the address is
configured can be of any type.
The above can result in the use of uninitialized memory when the address
is later compared against existing addresses since 'dev->addr_len' is
used and it may be greater than ETH_ALEN, as with ip6tnl devices.
Fix this by making sure that FDB entries are only configured for
Ethernet devices.
Fixes: 090096bf3db1 ("net: generic fdb support for drivers without ndo_fdb_<op>") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-and-tested-by: syzbot+3a288d5f5530b901310e@syzkaller.appspotmail.com Reported-and-tested-by: syzbot+d53ab4e92a1db04110ff@syzkaller.appspotmail.com Cc: Vlad Yasevich <vyasevich@gmail.com> Cc: David Ahern <dsahern@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've been getting checksum errors involving small UDP packets, usually
59B packets with 1 extra non-zero padding byte. netdev_rx_csum_fault()
has been complaining that HW is providing bad checksums. Turns out the
problem is in pskb_trim_rcsum_slow(), introduced in commit 88078d98d1bb
("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends").
The source of the problem is that when the bytes we are trimming start
at an odd address, as in the case of the 1 padding byte above,
skb_checksum() returns a byte-swapped value. We cannot just combine this
with skb->csum using csum_sub(). We need to use csum_block_sub() here
that takes into account the parity of the start address and handles the
swapping.
Matches existing code in __skb_postpull_rcsum() and esp_remove_trailer().
Fixes: 88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends") Signed-off-by: Dimitris Michailidis <dmichail@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most callers of pskb_trim_rcsum() simply drop the skb when
it fails, however, ip_check_defrag() still continues to pass
the skb up to stack. This is suspicious.
In ip_check_defrag(), after we learn the skb is an IP fragment,
passing the skb to callers makes no sense, because callers expect
fragments are defrag'ed on success. So, dropping the skb when we
can't defrag it is reasonable.
Note, prior to commit 88078d98d1bb, this is not a big problem as
checksum will be fixed up anyway. After it, the checksum is not
correct on failure.
Found this during code review.
Fixes: 88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends") Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The attribute IFLA_BOND_AD_ACTOR_SYSTEM is sent to user space having the
length of sizeof(bond->params.ad_actor_system) which is 8 byte. This
patch aligns the length to ETH_ALEN to have the same MAC address exposed
as using sysfs.
Fixes: f87fda00b6ed2 ("bonding: prevent out of bound accesses") Signed-off-by: Tobias Jungel <tobias.jungel@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dev_ethtool(), the eth command 'ethcmd' is firstly copied from the
use-space buffer 'useraddr' and checked to see whether it is
ETHTOOL_PERQUEUE. If yes, the sub-command 'sub_cmd' is further copied from
the user space. Otherwise, 'sub_cmd' is the same as 'ethcmd'. Next,
according to 'sub_cmd', a permission check is enforced through the function
ns_capable(). For example, the permission check is required if 'sub_cmd' is
ETHTOOL_SCOALESCE, but it is not necessary if 'sub_cmd' is
ETHTOOL_GCOALESCE, as suggested in the comment "Allow some commands to be
done by anyone". The following execution invokes different handlers
according to 'ethcmd'. Specifically, if 'ethcmd' is ETHTOOL_PERQUEUE,
ethtool_set_per_queue() is called. In ethtool_set_per_queue(), the kernel
object 'per_queue_opt' is copied again from the user-space buffer
'useraddr' and 'per_queue_opt.sub_command' is used to determine which
operation should be performed. Given that the buffer 'useraddr' is in the
user space, a malicious user can race to change the sub-command between the
two copies. In particular, the attacker can supply ETHTOOL_PERQUEUE and
ETHTOOL_GCOALESCE to bypass the permission check in dev_ethtool(). Then
before ethtool_set_per_queue() is called, the attacker changes
ETHTOOL_GCOALESCE to ETHTOOL_SCOALESCE. In this way, the attacker can
bypass the permission check and execute ETHTOOL_SCOALESCE.
This patch enforces a check in ethtool_set_per_queue() after the second
copy from 'useraddr'. If the sub-command is different from the one obtained
in the first copy in dev_ethtool(), an error code EINVAL will be returned.
Fixes: f38d138a7da6 ("net/ethtool: support set coalesce per queue") Signed-off-by: Wenwen Wang <wang6495@umn.edu> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The idx in vhost_vring_ioctl() was controlled by userspace, hence a
potential exploitation of the Spectre variant 1 vulnerability.
Fixing this by sanitizing idx before using it to index d->vqs.
Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported an use-after-free involving sctp_id2asoc. Dmitry Vyukov
helped to root cause it and it is because of reading the asoc after it
was freed:
CPU 1 CPU 2
(working on socket 1) (working on socket 2)
sctp_association_destroy
sctp_id2asoc
spin lock
grab the asoc from idr
spin unlock
spin lock
remove asoc from idr
spin unlock
free(asoc)
if asoc->base.sk != sk ... [*]
This can only be hit if trying to fetch asocs from different sockets. As
we have a single IDR for all asocs, in all SCTP sockets, their id is
unique on the system. An application can try to send stuff on an id
that matches on another socket, and the if in [*] will protect from such
usage. But it didn't consider that as that asoc may belong to another
socket, it may be freed in parallel (read: under another socket lock).
We fix it by moving the checks in [*] into the protected region. This
fixes it because the asoc cannot be freed while the lock is held.
Reported-by: syzbot+c7dd55d7aec49d48e49a@syzkaller.appspotmail.com Acked-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtl_rx() and rtl_tx() are called only if the respective bits are set
in the interrupt status register. Under high load NAPI may not be
able to process all data (work_done == budget) and it will schedule
subsequent calls to the poll callback.
rtl_ack_events() however resets the bits in the interrupt status
register, therefore subsequent calls to rtl8169_poll() won't call
rtl_rx() and rtl_tx() - chip interrupts are still disabled.
Fix this by calling rtl_rx() and rtl_tx() independent of the bits
set in the interrupt status register. Both functions will detect
if there's nothing to do for them.
Fixes: da78dbff2e05 ("r8169: remove work from irq handler.") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current handling of CHECKSUM_COMPLETE packets by the UDP stack is
incorrect for any packet that has an incorrect checksum value.
udp4/6_csum_init() will both make a call to
__skb_checksum_validate_complete() to initialize/validate the csum
field when receiving a CHECKSUM_COMPLETE packet. When this packet
fails validation, skb->csum will be overwritten with the pseudoheader
checksum so the packet can be fully validated by software, but the
skb->ip_summed value will be left as CHECKSUM_COMPLETE so that way
the stack can later warn the user about their hardware spewing bad
checksums. Unfortunately, leaving the SKB in this state can cause
problems later on in the checksum calculation.
Since the the packet is still marked as CHECKSUM_COMPLETE,
udp_csum_pull_header() will SUBTRACT the checksum of the UDP header
from skb->csum instead of adding it, leaving us with a garbage value
in that field. Once we try to copy the packet to userspace in the
udp4/6_recvmsg(), we'll make a call to skb_copy_and_csum_datagram_msg()
to checksum the packet data and add it in the garbage skb->csum value
to perform our final validation check.
Since the value we're validating is not the proper checksum, it's possible
that the folded value could come out to 0, causing us not to drop the
packet. Instead, we believe that the packet was checksummed incorrectly
by hardware since skb->ip_summed is still CHECKSUM_COMPLETE, and we attempt
to warn the user with netdev_rx_csum_fault(skb->dev);
Unfortunately, since this is the UDP path, skb->dev has been overwritten
by skb->dev_scratch and is no longer a valid pointer, so we end up
reading invalid memory.
This patch addresses this problem in two ways:
1) Do not use the dev pointer when calling netdev_rx_csum_fault()
from skb_copy_and_csum_datagram_msg(). Since this gets called
from the UDP path where skb->dev has been overwritten, we have
no way of knowing if the pointer is still valid. Also for the
sake of consistency with the other uses of
netdev_rx_csum_fault(), don't attempt to call it if the
packet was checksummed by software.
2) Add better CHECKSUM_COMPLETE handling to udp4/6_csum_init().
If we receive a packet that's CHECKSUM_COMPLETE that fails
verification (i.e. skb->csum_valid == 0), check who performed
the calculation. It's possible that the checksum was done in
software by the network stack earlier (such as Netfilter's
CONNTRACK module), and if that says the checksum is bad,
we can drop the packet immediately instead of waiting until
we try and copy it to userspace. Otherwise, we need to
mark the SKB as CHECKSUM_NONE, since the skb->csum field
no longer contains the full packet checksum after the
call to __skb_checksum_validate_complete().
Fixes: e6afc8ace6dd ("udp: remove headers from UDP packets before queueing") Fixes: c84d949057ca ("udp: copy skb->truesize in the first cache line") Cc: Sam Kumar <samanthakumar@google.com> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Sean Tranchetti <stranche@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building stmmac, it is only possible to select CONFIG_DWMAC_GENERIC,
or any of the glue drivers, when CONFIG_STMMAC_PLATFORM is set.
The only exception is CONFIG_STMMAC_PCI.
When calling of_mdiobus_register(), it will call our ->reset()
callback, which is set to stmmac_mdio_reset().
Most of the code in stmmac_mdio_reset() is protected by a
"#if defined(CONFIG_STMMAC_PLATFORM)", which will evaluate
to false when CONFIG_STMMAC_PLATFORM=m.
Because of this, the phy reset gpio will only be pulled when
stmmac is built as built-in, but not when built as modules.
Fix this by using "#if IS_ENABLED()" instead of "#if defined()".
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ethtool_ioctl(), the ioctl command 'ethcmd' is checked through a switch
statement to see whether it is necessary to pre-process the ethtool
structure, because, as mentioned in the comment, the structure
ethtool_rxnfc is defined with padding. If yes, a user-space buffer 'rxnfc'
is allocated through compat_alloc_user_space(). One thing to note here is
that, if 'ethcmd' is ETHTOOL_GRXCLSRLALL, the size of the buffer 'rxnfc' is
partially determined by 'rule_cnt', which is actually acquired from the
user-space buffer 'compat_rxnfc', i.e., 'compat_rxnfc->rule_cnt', through
get_user(). After 'rxnfc' is allocated, the data in the original user-space
buffer 'compat_rxnfc' is then copied to 'rxnfc' through copy_in_user(),
including the 'rule_cnt' field. However, after this copy, no check is
re-enforced on 'rxnfc->rule_cnt'. So it is possible that a malicious user
race to change the value in the 'compat_rxnfc->rule_cnt' between these two
copies. Through this way, the attacker can bypass the previous check on
'rule_cnt' and inject malicious data. This can cause undefined behavior of
the kernel and introduce potential security risk.
This patch avoids the above issue via copying the value acquired by
get_user() to 'rxnfc->rule_cn', if 'ethcmd' is ETHTOOL_GRXCLSRLALL.
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gred_change_table_def() takes a pointer to TCA_GRED_DPS attribute,
and expects it will be able to interpret its contents as
struct tc_gred_sopt. Pass the correct gred attribute, instead of
TCA_OPTIONS.
This bug meant the table definition could never be changed after
Qdisc was initialized (unless whatever TCA_OPTIONS contained both
passed netlink validation and was a valid struct tc_gred_sopt...).
Old behaviour:
$ ip link add type dummy
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
RTNETLINK answers: Invalid argument
Now:
$ ip link add type dummy
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
Fixes: f62d6b936df5 ("[PKT_SCHED]: GRED: Use central VQ change procedure") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The loop wants to skip previously dumped addresses, so loops until
current index >= saved index. If the message fills it wants to save
the index for the next address to dump - ie., the one that did not
fit in the current message.
Currently, it is incrementing the index counter before comparing to the
saved index, and then the saved index is off by 1 - it assumes the
current address is going to fit in the message.
Change the index handling to increment only after a succesful dump.
Fixes: 502a2ffd7376a ("ipv6: convert idev_list to list macros") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WHen an llc sock is added into the sk_laddr_hash of an llc_sap,
it is not marked with SOCK_RCU_FREE.
This causes that the sock could be freed while it is still being
read by __llc_lookup_established() with RCU read lock. sock is
refcounted, but with RCU read lock, nothing prevents the readers
getting a zero refcnt.
Fix it by setting SOCK_RCU_FREE in llc_sap_add_socket().
Reported-by: syzbot+11e05f04c15e03be5254@syzkaller.appspotmail.com Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a61bbcf28a8c ("[NET]: Store skb->timestamp as offset to a base
timestamp") introduces a neighbour control buffer and zeroes it out in
ndisc_rcv(), as ndisc_recv_ns() uses it.
Commit f2776ff04722 ("[IPV6]: Fix address/interface handling in UDP and
DCCP, according to the scoping architecture.") introduces the usage of the
IPv6 control buffer in protocol error handlers (e.g. inet6_iif() in
present-day __udp6_lib_err()).
Now, with commit b94f1c0904da ("ipv6: Use icmpv6_notify() to propagate
redirect, instead of rt6_redirect()."), we call protocol error handlers
from ndisc_redirect_rcv(), after the control buffer is already stolen and
some parts are already zeroed out. This implies that inet6_iif() on this
path will always return zero.
This gives unexpected results on UDP socket lookup in __udp6_lib_err(), as
we might actually need to match sockets for a given interface.
Instead of always claiming the control buffer in ndisc_rcv(), do that only
when needed.
Fixes: b94f1c0904da ("ipv6: Use icmpv6_notify() to propagate redirect, instead of rt6_redirect().") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot found a use-after-free in inet6_mc_check [1]
The problem here is that inet6_mc_check() uses rcu
and read_lock(&iml->sflock)
So the fact that ip6_mc_leave_src() is called under RTNL
and the socket lock does not help us, we need to acquire
iml->sflock in write mode.
In the future, we should convert all this stuff to RCU.
[1]
BUG: KASAN: use-after-free in ipv6_addr_equal include/net/ipv6.h:521 [inline]
BUG: KASAN: use-after-free in inet6_mc_check+0xae7/0xb40 net/ipv6/mcast.c:649
Read of size 8 at addr ffff8801ce7f2510 by task syz-executor0/22432
Memory state around the buggy address: ffff8801ce7f2400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8801ce7f2480: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff8801ce7f2500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8801ce7f2580: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff8801ce7f2600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently a check was added which prevents marking of routers with zero
source address, but for IPv6 that cannot happen as the relevant RFCs
actually forbid such packets:
RFC 2710 (MLDv1):
"To be valid, the Query message MUST
come from a link-local IPv6 Source Address, be at least 24 octets
long, and have a correct MLD checksum."
Same goes for RFC 3810.
And also it can be seen as a requirement in ipv6_mc_check_mld_query()
which is used by the bridge to validate the message before processing
it. Thus any queries with :: source address won't be processed anyway.
So just remove the check for zero IPv6 source address from the query
processing function.
Fixes: 5a2de63fd1a5 ("bridge: do not add port to router list when receives query with source 0.0.0.0") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch supporting IGMP snooping must maintain a list of
multicast routers and the ports on which they are attached. This
list can be constructed in any combination of the following ways:
a) This list should be built by the snooping switch sending
Multicast Router Solicitation messages as described in IGMP
Multicast Router Discovery [MRDISC]. It may also snoop
Multicast Router Advertisement messages sent by and to other
nodes.
b) The arrival port for IGMP Queries (sent by multicast routers)
where the source address is not 0.0.0.0.
We should not add the port to router list when receives query with source
0.0.0.0.
Reported-by: Ying Xu <yinxu@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Yocto build system does a 'make clean' when rebuilding due to
changed dependencies, and that consistently fails for me (causing the
whole BSP build to fail) with errors such as
| find: '[...]/perf/1.0-r9/perf-1.0/plugin_mac80211.so': No such file or directory
| find: '[...]/perf/1.0-r9/perf-1.0/plugin_mac80211.so': No such file or directory
| find: find: '[...]/perf/1.0-r9/perf-1.0/libtraceevent.a''[...]/perf/1.0-r9/perf-1.0/libtraceevent.a': No such file or directory: No such file or directory
|
[...]
| find: cannot delete '/mnt/xfs/devel/pil/yocto/tmp-glibc/work/wandboard-oe-linux-gnueabi/perf/1.0-r9/perf-1.0/util/.pstack.o.cmd': No such file or directory
Apparently (despite the comment), 'make clean' ends up launching
multiple sub-makes that all want to remove the same things - perhaps
this only happens in combination with a O=... parameter. In any case, we
don't lose much by explicitly disabling the parallelism for the clean
target, and it makes automated builds much more reliable.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20180705131527.19749-1-linux@rasmusvillemoes.dk Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It causes kernel crash for locally generated ipv6 fragments
when netfilter ipv6 defragmentation is used.
The faulty commit is not essential for -stable, it only
delays netns teardown for longer than needed when that netns
still has ipv6 frags queued. Much better than crash :-/
Added support for is25wp032, is25wp064 and is25wp128.
Signed-off-by: Kimmo Rautkoski <ext-kimmo.rautkoski@vaisala.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[ Adrian Bunk: Trivial adaption to changed context. ] Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
napi poll functions should be initialized before running request_irq(),
to handle a rare condition where there is a pending interrupt, causing
the ISR to fire immediately while the poll function wasn't set yet,
causing a NULL dereference.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux / log