PPP units don't hold any reference on the channels connected to it.
It is the channel's responsibility to ensure that it disconnects from
its unit before being destroyed.
In practice, this is ensured by ppp_unregister_channel() disconnecting
the channel from the unit before dropping a reference on the channel.
However, it is possible for an unregistered channel to connect to a PPP
unit: register a channel with ppp_register_net_channel(), attach a
/dev/ppp file to it with ioctl(PPPIOCATTCHAN), unregister the channel
with ppp_unregister_channel() and finally connect the /dev/ppp file to
a PPP unit with ioctl(PPPIOCCONNECT).
Once in this situation, the channel is only held by the /dev/ppp file,
which can be released at anytime and free the channel without letting
the parent PPP unit know. Then the ppp structure ends up with dangling
pointers in its ->channels list.
Prevent this scenario by forbidding unregistered channels from
connecting to PPP units. This maintains the code logic by keeping
ppp_unregister_channel() responsible from disconnecting the channel if
necessary and avoids modification on the reference counting mechanism.
This issue seems to predate git history (successfully reproduced on
Linux 2.6.26 and earlier PPP commits are unrelated).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nowadays, nlmsg_multicast() returns only 0 or -ESRCH but this was not the
case when commit 134e63756d5f was pushed.
However, there was no reason to stop the loop if a netns does not have
listeners.
Returns -ESRCH only if there was no listeners in all netns.
To avoid having the same problem in the future, I didn't take the
assumption that nlmsg_multicast() returns only 0 or -ESRCH.
Fixes: 134e63756d5f ("genetlink: make netns aware") CC: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
netif_set_real_num_tx_queues() can be called when netdev is up.
That usually happens when user requests change of number of
channels/rings with ethtool -L. The procedure for changing
the number of queues involves resetting the qdiscs and setting
dev->num_tx_queues to the new value. When the new value is
lower than the old one, extra care has to be taken to ensure
ordering of accesses to the number of queues vs qdisc reset.
Currently the queues are reset before new dev->num_tx_queues
is assigned, leaving a window of time where packets can be
enqueued onto the queues going down, leading to a likely
crash in the drivers, since most drivers don't check if TX
skbs are assigned to an active queue.
Fixes: e6484930d7c7 ("net: allocate tx queues in register_netdevice") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc-8 has a new warning that detects overlapping input and output arguments
in memcpy(). It triggers for sit_init_net() calling ipip6_tunnel_clone_6rd(),
which is actually correct:
net/ipv6/sit.c: In function 'sit_init_net':
net/ipv6/sit.c:192:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
The problem here is that the logic detecting the memcpy() arguments finds them
to be the same, but the conditional that tests for the input and output of
ipip6_tunnel_clone_6rd() to be identical is not a compile-time constant.
We know that netdev_priv(t->dev) is the same as t for a tunnel device,
and comparing "dev" directly here lets the compiler figure out as well
that 'dev == sitn->fb_tunnel_dev' when called from sit_init_net(), so
it no longer warns.
This code is old, so Cc stable to make sure that we don't get the warning
for older kernels built with new gcc.
Cc: Martin Sebor <msebor@gmail.com> Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83456 Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes when physical lines have a just good noise to make the protocol
handshaking fail, but the carrier detect still good. Then after remove of
the noise, nobody will trigger this protocol to be start again to cause
the link to never come back. The fix is when the carrier is still on, not
terminate the protocol handshaking.
Signed-off-by: Denis Du <dudenis2000@yahoo.ca> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In fib_nh_match(), if output interface or gateway are passed in
the FIB configuration, we don't have to check next hops of
multipath routes to conclude whether we have a match or not.
However, we might still have routes with different realms
matching the same output interface and gateway configuration,
and this needs to cause the match to fail. Otherwise the first
route inserted in the FIB will match, regardless of the realms:
# ip route add 1.1.1.1 dev eth0 table 1234 realms 1/2
# ip route append 1.1.1.1 dev eth0 table 1234 realms 3/4
# ip route list table 1234
1.1.1.1 dev eth0 scope link realms 1/2
1.1.1.1 dev eth0 scope link realms 3/4
# ip route del 1.1.1.1 dev ens3 table 1234 realms 3/4
# ip route list table 1234
1.1.1.1 dev ens3 scope link realms 3/4
whereas route with realms 3/4 should have been deleted instead.
Explicitly check for fc_flow passed in the FIB configuration
(this comes from RTA_FLOW extracted by rtm_to_fib_config()) and
fail matching if it differs from nh_tclassid.
The handling of RTA_FLOW for multipath routes later in
fib_nh_match() is still needed, as we can have multiple RTA_FLOW
attributes that need to be matched against the tclassid of each
next hop.
v2: Check that fc_flow is set before discarding the match, so
that the user can still select the first matching rule by
not specifying any realm, as suggested by David Ahern.
Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now br_sysfs_if file flush doesn't have attr show. To read it will
cause kernel panic after users chmod u+r this file.
Xiong found this issue when running the commands:
ip link add br0 type bridge
ip link add type veth
ip link set veth0 master br0
chmod u+r /sys/devices/virtual/net/veth0/brport/flush
timeout 3 cat /sys/devices/virtual/net/veth0/brport/flush
kernel crashed with NULL a pointer dereference call trace.
This patch is to fix it by return -EINVAL when brport_attr->show
is null, just the same as the check for brport_attr->store in
brport_store().
Fixes: 9cf637473c85 ("bridge: add sysfs hook to flush forwarding table") Reported-by: Xiong Zhou <xzhou@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Wed, 7 Mar 2018 18:36:43 +0000 (18:36 +0000)]
x86/apic/vector: Handle legacy irq data correctly
The backport of upstream commit 45d55e7bac40 ("x86/apic/vector: Fix off by
one in error path") missed to fixup the legacy interrupt data which is not
longer available upstream.
Handle legacy irq data correctly by clearing the legacy storage to prevent
use after free.
Fixes: 7fd133539289 ("x86/apic/vector: Fix off by one in error path") - 4.4.y Fixes: c557481a9491 ("x86/apic/vector: Fix off by one in error path") - 4.9.y Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before, if cb->start() failed, the module reference would never be put,
because cb->cb_running is intentionally false at this point. Users are
generally annoyed by this because they can no longer unload modules that
leak references. Also, it may be possible to tediously wrap a reference
counter back to zero, especially since module.c still uses atomic_inc
instead of refcount_inc.
This patch expands the error path to simply call module_put if
cb->start() fails.
Fixes: 41c87425a1ac ("netlink: do not set cb_running if dump's start() errs") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The locking protocols in md assume that a device will
never be removed from an array during resync/recovery/reshape.
When that isn't happening, rcu or reconfig_mutex is needed
to protect an rdev pointer while taking a refcount. When
it is happening, that protection isn't needed.
Unfortunately there are cases were remove_and_add_spares() is
called when recovery might be happening: is state_store(),
slot_store() and hot_remove_disk().
In each case, this is just an optimization, to try to expedite
removal from the personality so the device can be removed from
the array. If resync etc is happening, we just have to wait
for md_check_recover to find a suitable time to call
remove_and_add_spares().
This optimization and not essential so it doesn't
matter if it fails.
So change remove_and_add_spares() to abort early if
resync/recovery/reshape is happening, unless it is called
from md_check_recovery() as part of a newly started recovery.
The parameter "this" is only NULL when called from
md_check_recovery() so when it is NULL, there is no need to abort.
As this can result in a NULL dereference, the fix is suitable
for -stable.
cc: yuyufen <yuyufen@huawei.com> Cc: Tomasz Majchrzak <tomasz.majchrzak@intel.com> Fixes: 8430e7e0af9a ("md: disconnect device from personality before trying to remove it.") Cc: stable@ver.kernel.org (v4.8+) Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flush indirect branches when switching into a process that marked itself
non dumpable. This protects high value processes like gpg better,
without having too high performance overhead.
If done naïvely, we could switch to a kernel idle thread and then back
to the original process, such as:
process A -> idle -> process A
In such scenario, we do not have to do IBPB here even though the process
is non-dumpable, as we are switching back to the same process after a
hiatus.
To avoid the redundant IBPB, which is expensive, we track the last mm
user context ID. The cost is to have an extra u64 mm context id to track
the last mm we were using before switching to the init_mm used by idle.
Avoiding the extra IBPB is probably worth the extra memory for this
common scenario.
For those cases where tlb_defer_switch_to_init_mm() returns true (non
PCID), lazy tlb will defer switch to init_mm, so we will not be changing
the mm for the process A -> idle -> process A switch. So IBPB will be
skipped for this case.
Thanks to the reviewers and Andy Lutomirski for the suggestion of
using ctx_id which got rid of the problem of mm pointer recycling.
This adds two new variables to mmu_context_t: ctx_id and tlb_gen.
ctx_id uniquely identifies the mm_struct and will never be reused.
For a given mm_struct (and hence ctx_id), tlb_gen is a monotonic
count of the number of times that a TLB flush has been requested.
The pair (ctx_id, tlb_gen) can be used as an identifier for TLB
flush actions and will be used in subsequent patches to reliably
determine whether all needed TLB flushes have occurred on a given
CPU.
This patch is split out for ease of review. By itself, it has no
real effect other than creating and updating the new variables.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Reviewed-by: Nadav Amit <nadav.amit@gmail.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mel Gorman <mgorman@suse.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/413a91c24dab3ed0caa5f4e4d017d87b0857f920.1498751203.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at time.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: 687c27676151 ("ARM: dts: Add minimal support for LogicPD Torpedo
DM3730 devkit")
Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at times.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: ab8dd3aed011 ("ARM: DTS: Add minimal Support for Logic PD DM3730
SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If only a subset of the devices associated with multiple regions support
a given special operation (eg. DISCARD) then the dec_count() that is
used to set error for the region must increment the io->count.
Otherwise, when the dec_count() is called it can cause the dm-io
caller's bio to be completed multiple times. As was reported against
the dm-mirror target that had mirror legs with a mix of discard
capabilities.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=196077 Reported-by: Zhang Yi <yizhan@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though it is unconventional, some PCIe host implementations omit the
root ports entirely, and simply consist of a host bridge (which is not
modeled as a device in the PCI hierarchy) and a link.
When the downstream device is an endpoint, our current code does not seem
to mind this unusual configuration. However, when PCIe switches are
involved, the ASPM code assumes that any downstream switch port has a
parent, and blindly dereferences the bus->parent->self field of the pci_dev
struct to chain the downstream link state to the link state of the root
port. Given that the root port is missing, the link is not modeled at all,
and nor is the link state, and attempting to access it results in a NULL
pointer dereference and a crash.
Avoid this by allowing the link state chain to terminate at the downstream
port if no root port exists.
vmx_vcpu_run() and svm_vcpu_run() are large functions, and giving
branch hints to the compiler can actually make a substantial cycle
difference by keeping the fast path contiguous in memory.
With this optimization, the retpoline-guest/retpoline-host case is
about 50 cycles faster.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Jim Mattson <jmattson@google.com> Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: KarimAllah Ahmed <karahmed@amazon.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kvm@vger.kernel.org Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20180222154318.20361-3-pbonzini@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having a paravirt indirect call in the IBRS restore path is not a
good idea, since we are trying to protect from speculative execution
of bogus indirect branch targets. It is also slower, so use
native_wrmsrl() on the vmentry path too.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Jim Mattson <jmattson@google.com> Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: KarimAllah Ahmed <karahmed@amazon.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kvm@vger.kernel.org Cc: stable@vger.kernel.org Fixes: d28b387fb74da95d69d2615732f50cceb38e9a4d Link: http://lkml.kernel.org/r/20180222154318.20361-2-pbonzini@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason is that when creates new memslot, there is no guarantee for new
memslot not overlap with private memslots. This can be triggered by the
following program:
In banked-sr.c, we use a top-level '__asm__(".arch_extension virt")'
statement to allow compilation of a multi-CPU kernel for ARMv6
and older ARMv7-A that don't normally support access to the banked
registers.
This is considered to be a programming error by the gcc developers
and will no longer work in gcc-8, where we now get a build error:
/tmp/cc4Qy7GR.s:34: Error: Banked registers are not available with this architecture. -- `mrs r3,SP_usr'
/tmp/cc4Qy7GR.s:41: Error: Banked registers are not available with this architecture. -- `mrs r3,ELR_hyp'
/tmp/cc4Qy7GR.s:55: Error: Banked registers are not available with this architecture. -- `mrs r3,SP_svc'
/tmp/cc4Qy7GR.s:62: Error: Banked registers are not available with this architecture. -- `mrs r3,LR_svc'
/tmp/cc4Qy7GR.s:69: Error: Banked registers are not available with this architecture. -- `mrs r3,SPSR_svc'
/tmp/cc4Qy7GR.s:76: Error: Banked registers are not available with this architecture. -- `mrs r3,SP_abt'
Passign the '-march-armv7ve' flag to gcc works, and is ok here, because
we know the functions won't ever be called on pre-ARMv7VE machines.
Unfortunately, older compiler versions (4.8 and earlier) do not understand
that flag, so we still need to keep the asm around.
Backporting to stable kernels (4.6+) is needed to allow those to be built
with future compilers as well.
The MACH_ARMADA_375 and MACH_ARMADA_38X boards select ARM_ERRATA_753970,
but it was renamed to PL310_ERRATA_753970 by commit fa0ce4035d48 ("ARM:
7162/1: errata: tidy up Kconfig options for PL310 errata workarounds").
Fix the selects to use the new name.
Discovered with the
https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py
script. Fixes: fa0ce4035d48 ("ARM: 7162/1: errata: tidy up Kconfig options for
PL310 errata workarounds"
cc: stable@vger.kernel.org Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last expression in a statement expression need not be a bare
variable, quoting gcc docs
The last thing in the compound statement should be an expression
followed by a semicolon; the value of this subexpression serves as the
value of the entire construct.
and we already use that in e.g. the min/max macros which end with a
ternary expression.
This way, we can allow index to have const-qualified type, which will in
some cases avoid the need for introducing a local copy of index of
non-const qualified type. That, in turn, can prevent readers not
familiar with the internals of array_index_nospec from wondering about
the seemingly redundant extra variable, and I think that's worthwhile
considering how confusing the whole _nospec business is.
The expression _i&_mask has type unsigned long (since that is the type
of _mask, and the BUILD_BUG_ONs guarantee that _i will get promoted to
that), so in order not to change the type of the whole expression, add
a cast back to typeof(_i).
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Cc: linux-arch@vger.kernel.org Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/151881604837.17395.10812767547837568328.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the Intel Edison module is powered with 3.3V, the reboot command makes
the module stuck. If the module is powered at a greater voltage, like 4.4V
(as the Edison Mini Breakout board does), reboot works OK.
The official Intel Edison BSP sends the IPCMSG_COLD_RESET message to the
SCU by default. The IPCMSG_COLD_BOOT which is used by the upstream kernel
is only sent when explicitely selected on the kernel command line.
Use IPCMSG_COLD_RESET unconditionally which makes reboot work independent
of the power supply voltage.
[ tglx: Massaged changelog ]
Fixes: bda7b072de99 ("x86/platform/intel-mid: Implement power off sequence") Signed-off-by: Sebastian Panceac <sebastian@resin.io> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/1519810849-15131-1-git-send-email-sebastian@resin.io Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Older Xen versions (4.5 and before) might have problems migrating pv
guests with MSR_IA32_SPEC_CTRL having a non-zero value. So before
suspending zero that MSR and restore it after being resumed.
Gerd reports that ->i_mode may contain other bits besides S_IFCHR. Use
S_ISCHR() instead. Otherwise, get_user_pages_longterm() may fail on
device-dax instances when those are meant to be explicitly allowed.
Fixes: 2bb6d2837083 ("mm: introduce get_user_pages_longterm") Cc: <stable@vger.kernel.org> Reported-by: Gerd Rausch <gerd.rausch@oracle.com> Acked-by: Jane Chu <jane.chu@oracle.com> Reported-by: Haozhong Zhang <haozhong.zhang@intel.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a307a1e6bc0d "cpufreq: s3c: use cpufreq_generic_init()"
accidentally broke cpufreq on s3c2410 and s3c2412.
These two platforms don't have a CPU frequency table and used to skip
calling cpufreq_table_validate_and_show() for them. But with the
above commit, we started calling it unconditionally and that will
eventually fail as the frequency table pointer is NULL.
Fix this by calling cpufreq_table_validate_and_show() conditionally
again.
Fixes: a307a1e6bc0d "cpufreq: s3c: use cpufreq_generic_init()" Cc: 3.13+ <stable@vger.kernel.org> # v3.13+ Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change to flush_kernel_vmap_range() wasn't sufficient to avoid the
SMP stalls. The problem is some drivers call these routines with
interrupts disabled. Interrupts need to be enabled for flush_tlb_all()
and flush_cache_all() to work. This version adds checks to ensure
interrupts are not disabled before calling routines that need IPI
interrupts. When interrupts are disabled, we now drop into slower code.
The attached change fixes the ordering of cache and TLB flushes in
several cases. When we flush the cache using the existing PTE/TLB
entries, we need to flush the TLB after doing the cache flush. We don't
need to do this when we flush the entire instruction and data caches as
these flushes don't use the existing TLB entries. The same is true for
tmpalias region flushes.
The flush_kernel_vmap_range() and invalidate_kernel_vmap_range()
routines have been updated.
Secondly, we added a new purge_kernel_dcache_range_asm() routine to
pacache.S and use it in invalidate_kernel_vmap_range(). Nominally,
purges are faster than flushes as the cache lines don't have to be
written back to memory.
Hopefully, this is sufficient to resolve the remaining problems due to
cache speculation. So far, testing indicates that this is the case. I
did work up a patch using tmpalias flushes, but there is a performance
hit because we need the physical address for each page, and we also need
to sequence access to the tmpalias flush code. This increases the
probability of stalls.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org # 4.9+ Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On CPU hotunplug the enqueued timers of the unplugged CPU are migrated to a
live CPU. This happens from the control thread which initiated the unplug.
If the CPU on which the control thread runs came out from a longer idle
period then the base clock of that CPU might be stale because the control
thread runs prior to any event which forwards the clock.
In such a case the timers from the unplugged CPU are queued on the live CPU
based on the stale clock which can cause large delays due to increased
granularity of the outer timer wheels which are far away from base:;clock.
But there is a worse problem than that. The following sequence of events
illustrates it:
- CPU0 timer1 is queued expires = 59969 and base->clk = 59131.
The timer is queued at wheel level 2, with resulting expiry time = 60032
(due to level granularity).
- CPU1 enters idle @60007, with next timer expiry @60020.
- CPU0 is hotplugged at @60009
- CPU1 exits idle and runs the control thread which migrates the
timers from CPU0
timer1 is now queued in level 0 for immediate handling in the next
softirq because the requested expiry time 59969 is before CPU1 base->clk
60007
- CPU1 runs code which forwards the base clock which succeeds because the
next expiring timer. which was collected at idle entry time is still set
to 60020.
So it forwards beyond 60007 and therefore misses to expire the migrated
timer1. That timer gets expired when the wheel wraps around again, which
takes between 63 and 630ms depending on the HZ setting.
Address both problems by invoking forward_timer_base() for the control CPUs
timer base. All other places, which might run into a similar problem
(mod_timer()/add_timer_on()) already invoke forward_timer_base() to avoid
that.
We've added a quirk to enable the recent Lenovo dock support, where it
overwrites the pin configs of NID 0x17 and 19, not only updating the
pin config cache. It works right after the boot, but the problem is
that the pin configs are occasionally cleared when the machine goes to
PM. Meanwhile the quirk writes the pin configs only at the pre-probe,
so this won't be applied any longer.
For addressing that issue, this patch moves the code to overwrite the
pin configs into HDA_FIXUP_ACT_INIT section so that it's always
applied at both probe and resume time.
On some boards setting power_save to a non 0 value leads to clicking /
popping sounds when ever we enter/leave powersaving mode. Ideally we would
figure out how to avoid these sounds, but that is not always feasible.
This commit adds a blacklist for devices where powersaving is known to
cause problems and disables it on these devices.
Note I tried to put this blacklist in userspace first:
https://github.com/systemd/systemd/pull/8128
But the systemd maintainers rightfully pointed out that it would be
impossible to then later remove entries once we actually find a way to
make power-saving work on listed boards without issues. Having this list
in the kernel will allow removal of the blacklist entry in the same commit
which fixes the clicks / plops.
The blacklist only applies to the default power_save module-option value,
if a user explicitly sets the module-option then the blacklist is not
used.
[ added an ifdef CONFIG_PM for the build error -- tiwai]
tpm_transmit() does not offer an explicit interface to indicate the number
of valid bytes in the communication buffer. Instead, it relies on the
commandSize field in the TPM header that is encoded within the buffer.
Therefore, ensure that a) enough data has been written to the buffer, so
that the commandSize field is present and b) the commandSize field does not
announce more data than has been written to the buffer.
This should have been fixed with CVE-2011-1161 long ago, but apparently
a correct version of that patch never made it into the kernel.
Cc: stable@vger.kernel.org Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buffers used as tx_buf/rx_buf in a SPI transfer need to be DMA-safe.
This cannot be guaranteed for the buffers passed to tpm_tis_spi_read_bytes
and tpm_tis_spi_write_bytes. Therefore, we need to use our own DMA-safe
buffer and copy the data to/from it.
The buffer needs to be allocated separately, to ensure that it is
cacheline-aligned and not shared with other data, so that DMA can work
correctly.
Fixes: 0edbfea537d1 ("tpm/tpm_tis_spi: Add support for spi phy") Cc: stable@vger.kernel.org Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Making cmd_getticks 'const' introduced a couple of harmless warnings:
drivers/char/tpm/tpm_tis_core.c: In function 'probe_itpm':
drivers/char/tpm/tpm_tis_core.c:469:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:477:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:255:12: note: expected 'u8 * {aka unsigned char *}' but argument is of type 'const u8 * {aka const unsigned char *}'
static int tpm_tis_send_data(struct tpm_chip *chip, u8 *buf, size_t len)
This changes the related functions to all take 'const' pointers
so that gcc can see this as being correct. I had to slightly
modify the logic around tpm_tis_spi_transfer() for this to work
without introducing ugly casts.
Cc: stable@vger.kernel.org Fixes: 5e35bd8e06b9 ("tpm_tis: make array cmd_getticks static const to shink object code size") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCC7 is a bit too eager to generate suboptimal __multi3 calls (128bit
multiply with 128bit result) for MIPS64r6 builds, even in code which
doesn't explicitly use 128bit types, such as the following:
unsigned long func(unsigned long a, unsigned long b)
{
return a > (~0UL) / b;
}
Therefore implement __multi3, but only for MIPS64r6 with GCC7 as under
normal circumstances we wouldn't expect any calls to __multi3 to be
generated from kernel code.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: James Hogan <jhogan@kernel.org> Tested-by: Waldemar Brodkorb <wbx@openadk.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Maciej W. Rozycki <macro@mips.com> Cc: Matthew Fortune <matthew.fortune@mips.com> Cc: Florian Fainelli <florian@openwrt.org> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17890/ Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set_fipers() calling should be protected by spinlock in
case that any interrupt breaks related registers setting
and the function we expect. This patch is to move set_fipers()
to spinlock protecting area in ptp_gianfar_adjtime().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some sockopt handling functions were calculating the length of the
buffer to be written to userspace and then calculating it again when
actually writing the buffer, which could lead to some write not using
an up-to-date length.
This patch updates such places to just make use of the len variable.
Also, replace some sizeof(type) to sizeof(var).
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When cleaning up after a partially successful gntdev_mmap(), unmap the
successfully mapped grant pages otherwise Xen will kill the domain if
in debug mode (Attempt to implicitly unmap a granted PTE) or Linux will
kill the process and emit "BUG: Bad page map in process" if Xen is in
release mode.
This is only needed when use_ptemod is true because gntdev_put_map()
will unmap grant pages itself when use_ptemod is false.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'sh_eth' driver's probe() method would fail on the SolutionEngine7710
board and crash on SolutionEngine7712 board as the platform code is
hopelessly behind the driver's platform data -- it passes the PHY address
instead of 'struct sh_eth_plat_data *'; pass the latter to the driver in
order to fix the bug...
Fixes: 71557a37adb5 ("[netdrvr] sh_eth: Add SH7619 support") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the probing of the regulator is deferred, the memory allocated by
'mdiobus_alloc_size()' will be leaking.
It should be freed before the next call to 'sun4i_mdio_probe()' which will
reallocate it.
Fixes: 4bdcb1dd9feb ("net: Add MDIO bus driver for the Allwinner EMAC") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When loading the module after unloading it, the network interface would
not be enabled and thus wouldn't have a backend counterpart and unable
to be used by the guest.
The guest would face errors like:
[root@guest ~]# ethtool -i eth0
Cannot get driver information: No such device
[root@guest ~]# ifconfig eth0
eth0: error fetching interface information: Device not found
This patch initializes the state of the netfront device whenever it is
loaded manually, this state would communicate the netback to create its
device and establish the connection between them.
Signed-off-by: Eduardo Otubo <otubo@redhat.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a
check for "Invalid VF id". Currently, the check is done against max_vfs.
However, the user doesn't always create max_vfs. So, the check should be
against the created number of VFs. The number of bnxt_vf_info structures
that are allocated in bnxt_alloc_vf_resources routine is the "number of
requested VFs". So, if an "invalid VF id" falls between the requested
number of VFs and the max_vfs, the driver will be dereferencing an invalid
pointer.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Venkat Devvuru <venkatkumar.duvvuru@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flexcan_start_xmit() function compares the frame length with data
register length to write frame content into data[0] and data[1]
register. Data register length is 4 bytes and frame maximum length is 8
bytes.
Fix the check that compares frame length with 3. Because the register
length is 4.
Signed-off-by: Luu An Phu <phu.luuan@nxp.com> Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nl80211_nan_add_func() does not check if the required attribute
NL80211_NAN_FUNC_FOLLOW_UP_DEST is present when processing
NL80211_CMD_ADD_NAN_FUNCTION request. This request can be issued
by users with CAP_NET_ADMIN privilege and may result in NULL dereference
and a system crash. Add a check for the required attribute presence.
The original code for __i40e_chk_linearize didn't take into account the
fact that if a fragment is 16K in size or larger it has to be split over 2
descriptors and the smaller of those 2 descriptors will be on the trailing
edge of the transmit. As a result we can get into situations where we didn't
catch requests that could result in a Tx hang.
This patch takes care of that by subtracting the length of all but the
trailing edge of the stale fragment before we test for sum. By doing this
we can guarantee that we have all cases covered, including the case of a
fragment that spans multiple descriptors. We don't need to worry about
checking the inner portions of this since 12K is the maximum aligned DMA
size and that is larger than any MSS will ever be since the MTU limit for
jumbos is something on the order of 9K.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
libc-compat.h aims to prevent symbol collisions between uapi and libc
headers for each supported libc. This requires continuous coordination
between them.
The goal of this commit is to improve the situation for libcs (such as
musl) which are not yet supported and/or do not wish to be explicitly
supported, while not affecting supported libcs. More precisely, with
this commit, unsupported libcs can request the suppression of any
specific uapi definition by defining the correspondings _UAPI_DEF_*
macro as 0. This can fix symbol collisions for them, as long as the
libc headers are included before the uapi headers. Inclusion in the
other order is outside the scope of this commit.
All infrastructure in order to enable this fallback for unsupported
libcs is already in place, except that libc-compat.h unconditionally
defines all _UAPI_DEF_* macros to 1 for all unsupported libcs so that
any previous definitions are ignored. In order to fix this, this commit
merely makes these definitions conditional.
In the function ttm_page_alloc_init, kzalloc call is made for variable
_manager, we need to check its return value, it may return NULL.
Signed-off-by: Xiongwei Song <sxwjean@gmail.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the macvlan_uninit would free the macvlan port, so there is one
double free case in macvlan_common_newlink. When the macvlan port is just
created, then register_netdevice or netdev_upper_dev_link failed and they
would invoke macvlan_uninit. Then it would reach the macvlan_port_destroy
which triggers the double free.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using enhanced mode for IPoIB, two threads may execute xmit in
parallel to two different TX queues while the target is the same.
In this case, both of them will add the same neighbor to the path's
neigh link list and we might see the following message:
Analysis:
Two SKB are scheduled to be transmitted from two cores.
In ipoib_start_xmit, both gets NULL when calling ipoib_neigh_get.
Two calls to neigh_add_path are made. One thread takes the spin-lock
and calls ipoib_neigh_alloc which creates the neigh structure,
then (after the __path_find) the neigh is added to the path's neigh
link list. When the second thread enters the critical section it also
calls ipoib_neigh_alloc but in this case it gets the already allocated
ipoib_neigh structure, which is already linked to the path's neigh
link list and adds it again to the list. Which beside of triggering
the list, it creates a loop in the linked list. This loop leads to
endless loop inside path_rec_completion.
Solution:
Check list_empty(&neigh->list) before adding to the list.
Add a similar fix in "ipoib_multicast.c::ipoib_mcast_send"
Fixes: b63b70d87741 ('IPoIB: Use a private hash table for path lookup in xmit path') Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Reviewed-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ibmr.device is being set only after ib_alloc_mr() is successfully complete.
Therefore, in case imlx4_mr_enable() returns with error, the error flow
unwinder calls to mlx4_free_priv_pages(), which uses ibmr.device.
Such usage causes to NULL dereference oops and to fix it, the IB device
should be set in the mr struct earlier stage (e.g. prior to calling
mlx4_free_priv_pages()).
Fixes: 1b2cd0fc673c ("IB/mlx4: Support the new memory registration API") Signed-off-by: Nitzan Carmi <nitzanc@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We store per path and per device configuration data to identify the
path or device correctly. The per path configuration data might get
mixed up if the original request gets into error recovery and is
started with a random path mask.
This would lead to a wrong identification of a path in case of a CUIR
event for example.
Fix by copying the path mask from the original request to the error
recovery request in case it is a path verification request.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was seen when running an upstream kernel on Acer Chromebook R11. The
system was unstable as result.
Guard the log message with __printk_ratelimit to reduce the impact. This
won't prevent the interrupt storm from happening, but at least the system
remains stable.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Dmitry Torokhov <dtor@chromium.org> Cc: Joe Perches <joe@perches.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=197953 Link: https://lkml.kernel.org/r/1512234784-21038-1-git-send-email-linux@roeck-us.net Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ibmr.device is being set only after ib_alloc_mr() is
(successfully) complete. Therefore, in case mlx5_core_create_mkey()
return with error, the error flow calls mlx5_free_priv_descs()
which uses ibmr.device (which doesn't exist yet), causing
a NULL dereference oops.
To fix this, the IB device should be set in the mr struct earlier
stage (e.g. prior to calling mlx5_core_create_mkey()).
Fixes: 8a187ee52b04 ("IB/mlx5: Support the new memory registration API") Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Signed-off-by: Nitzan Carmi <nitzanc@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While in recovery process of PCI error (called EEH on PowerPC arch),
another PCI transaction could be corrupted causing a situation of
nested PCI errors. Also, this scenario could be reproduced with
error injection mechanisms (for debug purposes).
We observe that in case of nested PCI errors, bnx2x might attempt to
initialize its shmem and cause a kernel crash due to bad addresses
read from MCP. Multiple different stack traces were observed depending
on the point the second PCI error happens.
This patch avoids the crashes by:
* failing PCI recovery in case of nested errors (since multiple
PCI errors in a row are not expected to lead to a functional
adapter anyway), and by,
* preventing access to adapter FW when MCP is failed (we mark it as
failed when shmem cannot get initialized properly).
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Acked-by: Shahed Shaikh <Shahed.Shaikh@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A customer noticed RX path hang when MTU is changed on the fly while
running heavy traffic with NCSI enabled for 5717 and 5719. Since 5720
belongs to same ASIC family, we observed same issue and same fix
could solve this problem for 5720.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of AMD based server with 5762 hangs with jumbo frame traffic.
This AMD platform has southbridge limitation which is restricting MRRS
to 4000. As a work around, driver to restricts the MRRS to 2048 for
this particular 5762 NX1 card.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling tipc_mon_delete() before the monitor has been created will oops.
This can happen in tipc_enable_bearer() error path if tipc_disc_create()
fails.
Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix memory leak in tipc_enable_bearer() if enable_media() fails, and
cleanup with bearer_disable() if tipc_mon_create() fails.
Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current MIPS64r6 toolchains aren't able to generate efficient
DMULU/DMUHU based code for the C implementation of umul_ppmm(), which
performs an unsigned 64 x 64 bit multiply and returns the upper and
lower 64-bit halves of the 128-bit result. Instead it widens the 64-bit
inputs to 128-bits and emits a __multi3 intrinsic call to perform a 128
x 128 multiply. This is both inefficient, and it results in a link error
since we don't include __multi3 in MIPS linux.
For example commit 90a53e4432b1 ("cfg80211: implement regdb signature
checking") merged in v4.15-rc1 recently broke the 64r6_defconfig and
64r6el_defconfig builds by indirectly selecting MPILIB. The same build
errors can be reproduced on older kernels by enabling e.g. CRYPTO_RSA:
lib/mpi/generic_mpih-mul1.o: In function `mpihelp_mul_1':
lib/mpi/generic_mpih-mul1.c:50: undefined reference to `__multi3'
lib/mpi/generic_mpih-mul2.o: In function `mpihelp_addmul_1':
lib/mpi/generic_mpih-mul2.c:49: undefined reference to `__multi3'
lib/mpi/generic_mpih-mul3.o: In function `mpihelp_submul_1':
lib/mpi/generic_mpih-mul3.c:49: undefined reference to `__multi3'
lib/mpi/mpih-div.o In function `mpihelp_divrem':
lib/mpi/mpih-div.c:205: undefined reference to `__multi3'
lib/mpi/mpih-div.c:142: undefined reference to `__multi3'
Therefore add an efficient MIPS64r6 implementation of umul_ppmm() using
inline assembly and the DMULU/DMUHU instructions, to prevent __multi3
calls being emitted.
Fixes: 7fd08ca58ae6 ("MIPS: Add build support for the MIPS R6 ISA") Signed-off-by: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-mips@linux-mips.org Cc: linux-crypto@vger.kernel.org Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dtc warns about two 'clocks' properties that have an extraneous '1'
at the end:
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a:clocks[1])
Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2190000/sgtl5000@a
arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2190000/sgtl5000@a:clocks[1])
The clocks that get referenced here are fixed-rate, so they do not
take any argument, and dtc interprets the next cell as a phandle, which
is invalid.
When an I/O is returned with an srb_status of SRB_STATUS_INVALID_LUN
which has zero good_bytes it must be assigned an error. Otherwise the
I/O will be continuously requeued and will cause a deadlock in the case
where disks are being hot added and removed. sd_probe_async will wait
forever for its I/O to complete while holding scsi_sd_probe_domain.
Also returning the default error of DID_TARGET_FAILURE causes multipath
to not retry the I/O resulting in applications receiving I/O errors
before a failover can occur.
Signed-off-by: Cathy Avery <cavery@redhat.com> Signed-off-by: Long Li <longli@microsoft.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using GMAC4 the value written in PTP_SSIR should be shifted however
the shifted value is also used in subsequent calculations which results
in a bad timestamp value.
Signed-off-by: Fredrik Hallenberg <megahallon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now it's using IPV6_MIN_MTU as the min mtu in ip6_tnl_xmit, but
IPV6_MIN_MTU actually only works when the inner packet is ipv6.
With IPV6_MIN_MTU for ipv4 packets, the new pmtu for inner dst
couldn't be set less than 1280. It would cause tx_err and the
packet to be dropped when the outer dst pmtu is close to 1280.
Jianlin found it by running ipv4 traffic with the topo:
After changing eth2 mtu to 1300, the performance became very
low, or the connection was even broken. The issue also affects
ip4ip6 and ip6ip6 tunnels.
So if the inner packet is ipv4, 576 should be considered as the
min mtu.
Note that for ip4ip6 and ip6ip6 tunnels, the inner packet can
only be ipv4 or ipv6, but for gre6 tunnel, it may also be ARP.
This patch using 576 as the min mtu for non-ipv6 packet works
for all those cases.
Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arc_emac_rx() has some issues found by code review.
In case netdev_alloc_skb_ip_align() or dma_map_single() failure
rx fifo entry will not be returned to EMAC.
In case dma_map_single() failure previously allocated skb became
lost to driver. At the same time address of newly allocated skb
will not be provided to EMAC.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current solution would setup fixed and force link of 1Gbps to the both
GMAC on the default. However, The GMAC should always be put to link down
state when the GMAC is disabled on certain target boards. Otherwise,
the driver possibly receives unexpected data from the floating hardware
connection through the unused GMAC. Although the driver had been added
certain protection in RX path to get rid of such kind of unexpected data
sent to the upper stack.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In skylake platform, we hear a loud pop noise(0 dB) at start of
audio capture power up sequence. This patch removes the pop noise
from the recording by adding a delay before enabling ADC.
Signed-off-by: Abhijeet Kumar <abhijeet.kumar@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only part of atmel_spi_remove which needs to be atomic is hardware
reset.
atmel_spi_stop_dma calls dma_terminate_all and this needs interrupts
enabled.
atmel_spi_release_dma calls dma_release_channel and dma_release_channel
locks a mutex inside of spin_lock.
So the call of these functions can't be inside a spin_lock.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Radu Pirea <radu.pirea@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On my GP107 when I load nouveau after unloading it, for some reason the
GPU stopped sending or the CPU stopped receiving interrupts if MSI was
enabled.
Doing a rearm once before getting any interrupts fixes this.
Signed-off-by: Karol Herbst <kherbst@redhat.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Up to f5caf621ee35 ("x86/asm: Fix inline asm call constraints for Clang")
we were able to use x86 headers to build to the 'bpf' clang target, as
done by the BPF code in tools/perf/.
With that commit, we ended up with following failure for 'perf test LLVM', this
is because "clang ... -target bpf ..." fails since 4.0 does not have bpf inline
asm support and 6.0 does not recognize the register 'esp', fix it by guarding
that part with an #ifndef __BPF__, that is defined by clang when building to
the "bpf" target.
# perf test -v LLVM
37: LLVM search and compile :
37.1: Basic BPF llvm compile :
--- start ---
test child forked, pid 25526
Kernel build dir is set to /lib/modules/4.14.0+/build
set env: KBUILD_DIR=/lib/modules/4.14.0+/build
unset env: KBUILD_OPTS
include option is set to -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/7/include -I/home/acme/git/linux/arch/x86/include -I./arch/x86/include/generated -I/home/acme/git/linux/include -I./include -I/home/acme/git/linux/arch/x86/include/uapi -I./arch/x86/include/generated/uapi -I/home/acme/git/linux/include/uapi -I./include/generated/uapi -include /home/acme/git/linux/include/linux/kconfig.h
set env: NR_CPUS=4
set env: LINUX_VERSION_CODE=0x40e00
set env: CLANG_EXEC=/usr/local/bin/clang
set env: CLANG_OPTIONS=-xc
set env: KERNEL_INC_OPTIONS= -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/7/include -I/home/acme/git/linux/arch/x86/include -I./arch/x86/include/generated -I/home/acme/git/linux/include -I./include -I/home/acme/git/linux/arch/x86/include/uapi -I./arch/x86/include/generated/uapi -I/home/acme/git/linux/include/uapi -I./include/generated/uapi -include /home/acme/git/linux/include/linux/kconfig.h
set env: WORKING_DIR=/lib/modules/4.14.0+/build
set env: CLANG_SOURCE=-
llvm compiling command template: echo '/*
* bpf-script-example.c
* Test basic LLVM building
*/
#ifndef LINUX_VERSION_CODE
# error Need LINUX_VERSION_CODE
# error Example: for 4.2 kernel, put 'clang-opt="-DLINUX_VERSION_CODE=0x40200" into llvm section of ~/.perfconfig'
#endif
#define BPF_ANY 0
#define BPF_MAP_TYPE_ARRAY 2
#define BPF_FUNC_map_lookup_elem 1
#define BPF_FUNC_map_update_elem 2
SEC("func=SyS_epoll_wait")
int bpf_func__SyS_epoll_wait(void *ctx)
{
int ind =0;
int *flag = bpf_map_lookup_elem(&flip_table, &ind);
int new_flag;
if (!flag)
return 0;
/* flip flag and store back */
new_flag = !*flag;
bpf_map_update_elem(&flip_table, &ind, &new_flag, BPF_ANY);
return new_flag;
}
char _license[] SEC("license") = "GPL";
int _version SEC("version") = LINUX_VERSION_CODE;
' | $CLANG_EXEC -D__KERNEL__ -D__NR_CPUS__=$NR_CPUS -DLINUX_VERSION_CODE=$LINUX_VERSION_CODE $CLANG_OPTIONS $KERNEL_INC_OPTIONS -Wno-unused-value -Wno-pointer-sign -working-directory $WORKING_DIR -c "$CLANG_SOURCE" -target bpf -O2 -o -
test child finished with 0
---- end ----
LLVM search and compile subtest 0: Ok
37.2: kbuild searching :
--- start ---
test child forked, pid 25950
Kernel build dir is set to /lib/modules/4.14.0+/build
set env: KBUILD_DIR=/lib/modules/4.14.0+/build
unset env: KBUILD_OPTS
include option is set to -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/7/include -I/home/acme/git/linux/arch/x86/include -I./arch/x86/include/generated -I/home/acme/git/linux/include -I./include -I/home/acme/git/linux/arch/x86/include/uapi -I./arch/x86/include/generated/uapi -I/home/acme/git/linux/include/uapi -I./include/generated/uapi -include /home/acme/git/linux/include/linux/kconfig.h
set env: NR_CPUS=4
set env: LINUX_VERSION_CODE=0x40e00
set env: CLANG_EXEC=/usr/local/bin/clang
set env: CLANG_OPTIONS=-xc
set env: KERNEL_INC_OPTIONS= -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/7/include -I/home/acme/git/linux/arch/x86/include -I./arch/x86/include/generated -I/home/acme/git/linux/include -I./include -I/home/acme/git/linux/arch/x86/include/uapi -I./arch/x86/include/generated/uapi -I/home/acme/git/linux/include/uapi -I./include/generated/uapi -include /home/acme/git/linux/include/linux/kconfig.h
set env: WORKING_DIR=/lib/modules/4.14.0+/build
set env: CLANG_SOURCE=-
llvm compiling command template: echo '/*
* bpf-script-test-kbuild.c
* Test include from kernel header
*/
#ifndef LINUX_VERSION_CODE
# error Need LINUX_VERSION_CODE
# error Example: for 4.2 kernel, put 'clang-opt="-DLINUX_VERSION_CODE=0x40200" into llvm section of ~/.perfconfig'
#endif
#define SEC(NAME) __attribute__((section(NAME), used))
SEC("func=vfs_llseek")
int bpf_func__vfs_llseek(void *ctx)
{
return 0;
}
char _license[] SEC("license") = "GPL";
int _version SEC("version") = LINUX_VERSION_CODE;
' | $CLANG_EXEC -D__KERNEL__ -D__NR_CPUS__=$NR_CPUS -DLINUX_VERSION_CODE=$LINUX_VERSION_CODE $CLANG_OPTIONS $KERNEL_INC_OPTIONS -Wno-unused-value -Wno-pointer-sign -working-directory $WORKING_DIR -c "$CLANG_SOURCE" -target bpf -O2 -o -
In file included from <stdin>:12:
In file included from /home/acme/git/linux/arch/x86/include/uapi/asm/ptrace.h:5:
In file included from /home/acme/git/linux/include/linux/compiler.h:242:
In file included from /home/acme/git/linux/arch/x86/include/asm/barrier.h:5:
In file included from /home/acme/git/linux/arch/x86/include/asm/alternative.h:10:
/home/acme/git/linux/arch/x86/include/asm/asm.h:145:50: error: unknown register name 'esp' in asm
register unsigned long current_stack_pointer asm(_ASM_SP);
^
/home/acme/git/linux/arch/x86/include/asm/asm.h:44:18: note: expanded from macro '_ASM_SP'
#define _ASM_SP __ASM_REG(sp)
^
/home/acme/git/linux/arch/x86/include/asm/asm.h:27:32: note: expanded from macro '__ASM_REG'
#define __ASM_REG(reg) __ASM_SEL_RAW(e##reg, r##reg)
^
/home/acme/git/linux/arch/x86/include/asm/asm.h:18:29: note: expanded from macro '__ASM_SEL_RAW'
# define __ASM_SEL_RAW(a,b) __ASM_FORM_RAW(a)
^
/home/acme/git/linux/arch/x86/include/asm/asm.h:11:32: note: expanded from macro '__ASM_FORM_RAW'
# define __ASM_FORM_RAW(x) #x
^
<scratch space>:4:1: note: expanded from here
"esp"
^
1 error generated.
ERROR: unable to compile -
Hint: Check error message shown above.
Hint: You can also pre-compile it into .o using:
clang -target bpf -O2 -c -
with proper -I and -D options.
Failed to compile test case: 'kbuild searching'
test child finished with -1
---- end ----
LLVM search and compile subtest 1: FAILED!
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Potapenko <glider@google.com> Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: David Ahern <dsahern@gmail.com> Cc: Dmitriy Vyukov <dvyukov@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wang Nan <wangnan0@huawei.com> Cc: Yonghong Song <yhs@fb.com> Link: https://lkml.kernel.org/r/20171128175948.GL3298@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An additional 'ip' will be pushed to the stack, for restoring the
DACR later, if CONFIG_CPU_SW_DOMAIN_PAN defined.
However, the fixup still get the err_ptr by add #8*4 to sp, which
results in the fact that the code area pointed by the LR will be
overwritten, or the kernel will crash if CONFIG_DEBUG_RODATA is enabled.
One example of when an ICMPv6 packet is required to be looped back is
when a host acts as both a Multicast Listener and a Multicast Router.
A Multicast Router will listen on address ff02::16 for MLDv2 messages.
Currently, MLDv2 messages originating from a Multicast Listener running
on the same host as the Multicast Router are not being delivered to the
Multicast Router. This is due to dst.input being assigned the default
value of dst_discard.
This results in the packet being looped back but discarded before being
delivered to the Multicast Router.
This patch sets dst.input to ip6_input to ensure a looped back packet
is delivered to the Multicast Router.
Signed-off-by: Brendan McGrath <redmcg@redmandi.dyndns.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A negative return value of brcmstb_nand_verify_erased_page() indicates a
real bitflip error of an erased page, and other return values (>= 0) show
the corrected bitflip number. Zero return value means no bitflip, but the
current driver code treats it as an error, and eventually leads to
falsely reported ECC error.
Fixes: 02b88eea9f9c ("mtd: brcmnand: Add check for erased page bitflip") Signed-off-by: Albert Hsieh <wen.hsieh@broadcom.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When erased subpages are read then the BCH decoder returns STATUS_ERASED
if they are all empty, or STATUS_UNCORRECTABLE if there are bitflips.
When there are bitflips, we have to set these bits again to show the
upper layers a completely erased page. When a bitflip happens in the
exact byte where the bad block marker is, then this byte is swapped
with another byte in block_mark_swapping(). The correction code then
detects a bitflip in another subpage and no longer corrects the bitflip
where it really happens.
Correct this behaviour by calling block_mark_swapping() after the
bitflips have been corrected.
In our case UBIFS failed with this bug because it expects erased
pages to be really empty:
UBIFS error (pid 187): ubifs_scan: corrupt empty space at LEB 36:118735
UBIFS error (pid 187): ubifs_scanned_corruption: corruption at LEB 36:118735
UBIFS error (pid 187): ubifs_scanned_corruption: first 8192 bytes from LEB 36:118735
UBIFS error (pid 187): ubifs_scan: LEB 36 scanning failed
UBIFS error (pid 187): do_commit: commit failed, error -117
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Richard Weinberger <richard@nod.at> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices with IDs matching the "stripe" quirk don't actually have
this quirk, and don't have an MDTS value. When MDTS is not set, the
driver sets the max sectors to UINT_MAX, which is not a power of 2,
hitting a BUG_ON from blk_queue_chunk_sectors. This patch skips setting
chunk sectors for such devices.
Signed-off-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously enabled clks are only disabled if clk_prepare_enable() fails.
However, there are other error paths were the previously enabled
clocks are not disabled.
To fix the problem, fsl_disable_clocks() now takes the number of clocks
that shall be disabled + unprepared. For existing calls were all clocks
were already successfully prepared + enabled, DMAMUX_NR is passed to
disable + unprepare all clocks.
In error paths were only some clocks were successfully prepared +
enabled the loop counter is passed, in order to disable + unprepare
all successfully prepared + enabled clocks.
Found by Linux Driver Verification project (linuxtesting.org).
One I2C bus on my Atom E3845 board has been broken since 4.9.
It has two devices, both declared by ACPI and with built-in drivers.
There are two back-to-back transactions originating from the kernel, one
targeting each device. The first transaction works, the second one locks
up the I2C controller. The controller never recovers.
These kernel logs show up whenever an I2C transaction is attempted after
this failure.
i2c-designware-pci 0000:00:18.3: timeout in disabling adapter
i2c-designware-pci 0000:00:18.3: timeout waiting for bus ready
Waiting for the I2C controller status to indicate that it is enabled
before programming it fixes the issue.
I have tested this patch on 4.14 and 4.15.
Fixes: commit 2702ea7dbec5 ("i2c: designware: wait for disable/enable only if necessary") Cc: linux-stable <stable@vger.kernel.org> #4.13+ Signed-off-by: Ben Gardner <gardner.ben@gmail.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
[Jarkko: Backported to v4.9..v4.12 before i2c-designware-core.c was renamed to i2c-designware-master.c] Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The POSIX specification defines that relative CLOCK_REALTIME timers are not
affected by clock modifications. Those timers have to use CLOCK_MONOTONIC
to ensure POSIX compliance.
The introduction of the additional HRTIMER_MODE_PINNED mode broke this
requirement for pinned timers.
There is no user space visible impact because user space timers are not
using pinned mode, but for consistency reasons this needs to be fixed.
Check whether the mode has the HRTIMER_MODE_REL bit set instead of
comparing with HRTIMER_MODE_ABS.
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de> Cc: Christoph Hellwig <hch@lst.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: keescook@chromium.org Fixes: 597d0275736d ("timers: Framework for identifying pinned timers") Link: http://lkml.kernel.org/r/20171221104205.7269-7-anna-maria@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Mike Galbraith <efault@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At entry userspace may have (maliciously) populated the extra registers
outside the syscall calling convention with arbitrary values that could
be useful in a speculative execution (Spectre style) attack.
Clear these registers to minimize the kernel's attack surface.
Note, this only clears the extra registers and not the unused
registers for syscalls less than 6 arguments, since those registers are
likely to be clobbered well before their values could be put to use
under speculation.
Note, Linus found that the XOR instructions can be executed with
minimized cost if interleaved with the PUSH instructions, and Ingo's
analysis found that R10 and R11 should be included in the register
clearing beyond the typical 'extra' syscall calling convention
registers.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Reported-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Cc: <stable@vger.kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/151787988577.7847.16733592218894189003.stgit@dwillia2-desk3.amr.corp.intel.com
[ Made small improvements to the changelog and the code comments. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until there is a solution to the dma-to-dax vs truncate problem it is
not safe to allow V4L2, Exynos, and other frame vector users to create
long standing / irrevocable memory registrations against filesytem-dax
vmas.
[dan.j.williams@intel.com: add comment for vma_is_fsdax() check in get_vaddr_frames(), per Jan] Link: http://lkml.kernel.org/r/151197874035.26211.4061781453123083667.stgit@dwillia2-desk3.amr.corp.intel.com Link: http://lkml.kernel.org/r/151068939985.7446.15684639617389154187.stgit@dwillia2-desk3.amr.corp.intel.com Fixes: 3565fce3a659 ("mm, x86: get_user_pages() for dax mappings") Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Inki Dae <inki.dae@samsung.com> Cc: Seung-Woo Kim <sw0312.kim@samsung.com> Cc: Joonyoung Shim <jy0922.shim@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Mauro Carvalho Chehab <mchehab@kernel.org> Cc: Mel Gorman <mgorman@suse.de> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Christoph Hellwig <hch@lst.de> Cc: Doug Ledford <dledford@redhat.com> Cc: Hal Rosenstock <hal.rosenstock@gmail.com> Cc: Jason Gunthorpe <jgg@mellanox.com> Cc: Jeff Moyer <jmoyer@redhat.com> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Cc: Sean Hefty <sean.hefty@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux / log