The 'missing-field-initializers' warning was reported
when building with W=2.
This patch use designated initializers for
'struct ffa_send_direct_data' to suppress the warning
and clarify the initialization intent.
The expander phy will be treated as broadcast flutter in the next
revalidation after the exp-attached end device probe failed, as follows:
[78779.654026] sas: broadcast received: 0
[78779.654037] sas: REVALIDATING DOMAIN on port 0, pid:10
[78779.654680] sas: ex 500e004aaaaaaa1f phy05 change count has changed
[78779.662977] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE)
[78779.662986] sas: ex 500e004aaaaaaa1f phy05 new device attached
[78779.663079] sas: ex 500e004aaaaaaa1f phy05:U:8 attached: 500e004aaaaaaa05 (stp)
[78779.693542] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] found
[78779.701155] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[78779.707864] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
...
[78835.161307] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[78835.171344] sas: sas_probe_sata: for exp-attached device 500e004aaaaaaa05 returned -19
[78835.180879] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] is gone
[78835.187487] sas: broadcast received: 0
[78835.187504] sas: REVALIDATING DOMAIN on port 0, pid:10
[78835.188263] sas: ex 500e004aaaaaaa1f phy05 change count has changed
[78835.195870] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE)
[78835.195875] sas: ex 500e004aaaaaaa1f rediscovering phy05
[78835.196022] sas: ex 500e004aaaaaaa1f phy05:U:A attached: 500e004aaaaaaa05 (stp)
[78835.196026] sas: ex 500e004aaaaaaa1f phy05 broadcast flutter
[78835.197615] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
The cause of the problem is that the related ex_phy's attached_sas_addr was
not cleared after the end device probe failed, so reset it.
Signed-off-by: Xingui Yang <yangxingui@huawei.com> Link: https://lore.kernel.org/r/20240619091742.25465-1-yangxingui@huawei.com Reviewed-by: John Garry <john.g.garry@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a PCI device is removed during eeh_pe_report_edev(), edev->pdev
will change and can cause a crash, hold the PCI rescan/remove lock
while taking a copy of edev->pdev->bus.
Reading the dispatch trace log from /sys/kernel/debug/powerpc/dtl/cpu-*
results in a BUG() when the config CONFIG_HARDENED_USERCOPY is enabled as
shown below.
Commit 6d07d1cd300f ("usercopy: Restrict non-usercopy caches to size 0")
requires that only whitelisted areas in slab/slub objects can be copied to
userspace when usercopy hardening is enabled using CONFIG_HARDENED_USERCOPY.
Dtl contains hypervisor dispatch events which are expected to be read by
privileged users. Hence mark this safe for user access.
Specify useroffset=0 and usersize=DISPATCH_LOG_BYTES to whitelist the
entire object.
mac802154 devices update their dev->stats fields locklessly. Therefore
these counters should be updated atomically. Adopt SMP safe DEV_STATS_INC()
and DEV_STATS_ADD() to achieve this.
Since the CONFIG_CTL register is only 32 bits wide in the Stromer
and Stromer Plus PLLs , the 'config_ctl_hi_val' values from the
IPQ5018 and IPQ5332 configurations are not used so remove those.
[How]
Disable MALL PG and make it always on until SMU firmware is ready.
Signed-off-by: Li Ma <li.ma@amd.com> Reviewed-by: Tim Huang <Tim.Huang@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When dmaengine supports pause function, in suspend state,
dmaengine_pause() is called instead of dmaengine_terminate_async(),
In end of playback stream, the runtime->state will go to
SNDRV_PCM_STATE_DRAINING, if system suspend & resume happen
at this time, application will not resume playback stream, the
stream will be closed directly, the dmaengine_terminate_async()
will not be called before the dmaengine_synchronize(), which
violates the call sequence for dmaengine_synchronize().
This behavior also happens for capture streams, but there is no
SNDRV_PCM_STATE_DRAINING state for capture. So use
dmaengine_tx_status() to check the DMA status if the status is
DMA_PAUSED, then call dmaengine_terminate_async() to terminate
dmaengine before dmaengine_synchronize().
Below is a summary of how the driver stores a reference to an skb during
transmit:
tx_buff[free_map[consumer_index]]->skb = new_skb;
free_map[consumer_index] = IBMVNIC_INVALID_MAP;
consumer_index ++;
Where variable data looks like this:
free_map == [4, IBMVNIC_INVALID_MAP, IBMVNIC_INVALID_MAP, 0, 3]
consumer_index^
tx_buff == [skb=null, skb=<ptr>, skb=<ptr>, skb=null, skb=null]
The driver has checks to ensure that free_map[consumer_index] pointed to
a valid index but there was no check to ensure that this index pointed
to an unused/null skb address. So, if, by some chance, our free_map and
tx_buff lists become out of sync then we were previously risking an
skb memory leak. This could then cause tcp congestion control to stop
sending packets, eventually leading to ETIMEDOUT.
Therefore, add a conditional to ensure that the skb address is null. If
not then warn the user (because this is still a bug that should be
patched) and free the old pointer to prevent memleak/tcp problems.
Signed-off-by: Nick Child <nnac123@linux.ibm.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If during the quota disable we fail when cleaning the quota tree or when
deleting the root from the root tree, we jump to the 'out' label without
ever dropping the reference on the quota root, resulting in a leak of the
root since fs_info->quota_root is no longer pointing to the root (we have
set it to NULL just before those steps).
Fix this by always doing a btrfs_put_root() call under the 'out' label.
This is a problem that exists since qgroups were first added in 2012 by
commit bed92eae26cc ("Btrfs: qgroup implementation and prototypes"), but
back then we missed a kfree on the quota root and free_extent_buffer()
calls on its root and commit root nodes, since back then roots were not
yet reference counted.
Reviewed-by: Boris Burkov <boris@bur.io> Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[BUG]
When running btrfs/060 with forced RST feature, it would crash the
following ASSERT() inside scrub_read_endio():
ASSERT(sector_nr < stripe->nr_sectors);
Before that, we would have tree dump from
btrfs_get_raid_extent_offset(), as we failed to find the RST entry for
the range.
[CAUSE]
Inside scrub_submit_extent_sector_read() every time we allocated a new
bbio we immediately called btrfs_map_block() to make sure there was some
RST range covering the scrub target.
But if btrfs_map_block() fails, we immediately call endio for the bbio,
while the bbio is newly allocated, it's completely empty.
Then inside scrub_read_endio(), we go through the bvecs to find
the sector number (as bi_sector is no longer reliable if the bio is
submitted to lower layers).
And since the bio is empty, such bvecs iteration would not find any
sector matching the sector, and return sector_nr == stripe->nr_sectors,
triggering the ASSERT().
[FIX]
Instead of calling btrfs_map_block() after allocating a new bbio, call
btrfs_map_block() first.
Since our only objective of calling btrfs_map_block() is only to update
stripe_len, there is really no need to do that after btrfs_alloc_bio().
This new timing would avoid the problem of handling empty bbio
completely, and in fact fixes a possible race window for the old code,
where if the submission thread is the only owner of the pending_io, the
scrub would never finish (since we didn't decrease the pending_io
counter).
Although the root cause of RST lookup failure still needs to be
addressed.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On the LG Gram 16Z90S, the WMAB and WMBB ACPI methods are not mapped
under \XINI, but instead are mapped under \_SB.XINI.
The reason for this is that the LGEX0820 ACPI device used by this
driver is mapped at \_SB.XINI, so the ACPI methods where moved as well
to appear below the LGEX0820 ACPI device.
Fix this by using the ACPI handle from the ACPI device when evaluating
both methods.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218901 Tested-by: Agathe Boutmy <agathe@boutmy.com> Signed-off-by: Armin Wolf <W_Armin@gmx.de> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20240606233540.9774-5-W_Armin@gmx.de Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The LGEX0815 ACPI device id is used for handling hotkey events, but
this functionality is already handled by the wireless-hotkey driver.
The LGEX0820 ACPI device id however is used to manage various
platform features using the WMAB/WMBB ACPI methods. Use this ACPI
device id to avoid blocking the wireless-hotkey driver from probing.
Tested-by: Agathe Boutmy <agathe@boutmy.com> Signed-off-by: Armin Wolf <W_Armin@gmx.de> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20240606233540.9774-4-W_Armin@gmx.de Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rfkill hotkey handling is already provided by the wireless-hotkey
driver. Remove the now unnecessary rfkill hotkey handling to avoid
duplicating functionality.
The ACPI notify handler still prints debugging information when
receiving ACPI notifications to aid in reverse-engineering.
Tested-by: Agathe Boutmy <agathe@boutmy.com> Signed-off-by: Armin Wolf <W_Armin@gmx.de> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20240606233540.9774-3-W_Armin@gmx.de Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The LGEX0815 ACPI device is used by the "LG Airplane Mode Button"
Windows driver for handling rfkill requests. When the ACPI device
receives an 0x80 ACPI notification, an rfkill event is to be
send to userspace.
Add support for the LGEX0815 ACPI device to the driver.
Tested-by: Agathe Boutmy <agathe@boutmy.com> Signed-off-by: Armin Wolf <W_Armin@gmx.de> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20240606233540.9774-2-W_Armin@gmx.de Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If sclp_init() fails it only partially cleans up: if there are multiple
failing calls to sclp_init() sclp_state_change_event will be added several
times to sclp_reg_list, which results in the following warning:
Fill this in so user-space can identify multiple ports on the same CP
unit.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the driver supports more devices over time the single MODULE_ALIAS
is complete and raises several warnings:
SPI driver ads7846 has no spi_device_id for ti,tsc2046
SPI driver ads7846 has no spi_device_id for ti,ads7843
SPI driver ads7846 has no spi_device_id for ti,ads7845
SPI driver ads7846 has no spi_device_id for ti,ads7873
Fix this by adding a spi_device_id table and removing the manual
MODULE_ALIAS.
If the ASP1 DAI is hooked up by the machine driver the ASP TX mixer
sources should be initialized to disconnected. There aren't currently
any available products using the ASP so this doesn't affect any
existing systems.
The cs35l56 does not have any fixed default for the mixer source
registers. When the cs35l56 boots, its firmware patches these registers
to setup a system-specific routing; this is so that Windows can use
generic SDCA drivers instead of needing knowledge of chip-specific
registers. The setup varies between end-products, which each have
customized firmware, and so the default register state varies between
end-products. It can also change if the firmware on an end-product is
upgraded - for example if a change was needed to the routing for Windows
use-cases. It must be emphasized that the settings applied by the
firmware are not internal magic tuning; they are statically implementing
use-case setup that on Linux would be done via ALSA controls.
The driver is currently syncing the mixer controls with whatever
initial state the firmware wrote to the registers, so that they report
the actual audio routing. But if the ASP DAI is hooked up this can create
a powered-up DAPM graph without anything intentionally setting up a path.
This can lead to parts of the audio system powering up unexpectedly.
For example when cs35l56 is connected to cs42l43 using a codec-codec link,
this can create a complete DAPM graph which then powers-up cs42l43. But
the cs42l43 can only be clocked from its SoundWire bus so this causes a
bunch of errors in the kernel log where cs42l43 is unexpectedly powered-up
without a clock.
If the host is taking ownership of the ASP (either directly or as a
codec-to-codec link) there is no need to keep the mixer settings that the
firmware wrote. The driver has ALSA controls for setting these using
standard Linux mechanisms. So if the machine driver hooks up the ASP the
ASP mixers are initialized to "None" (no input). This prevents unintended
DAPM-graph power-ups, and means the initial state of the mixers is
always going to be None.
Since the initial state of the mixers can vary from system to system and
potentially between firmware upgrades, no use-case manager can currently
assume that cs35l56 has a known initial state. The firmware could just as
easily default them to "None" as to any input source. So defaulting them
to "None" in the driver is not increasing the entropy of the system.
The minimum period size was enforced to 64 as older devices integrating
McASP with EDMA used an internal FIFO of 64 samples.
With UDMA based platforms this internal McASP FIFO is optional, as the
DMA engine internally does some buffering which is already accounted for
when registering the platform. So we should read the actual FIFO
configuration (txnumevt/rxnumevt) instead of hardcoding frames.min to
64.
Sometimes the stream may be stopped due to XRUN events, in which case
the userspace can call snd_pcm_drop() and snd_pcm_prepare() to stop and
start the stream again.
In these cases, we must wait for the DMA channel to synchronize before
marking the stream as prepared for playback, as the DMA channel gets
stopped by drop() without any synchronization. Make sure the ALSA core
synchronizes the DMA channel by adding a sync_stop() hook.
When headphones are plugged in, they appear absent; when they are removed,
they appear present.
Add a specific entry in bytcr_rt5640 for this device
Signed-off-by: Thomas GENTY <tomlohave@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20240608170251.99936-1-tomlohave@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Most users after parsing a topology file, release memory used by it, so
having pointer references directly into topology file contents is wrong.
Use devm_kmemdup(), to allocate memory as needed.
The Lenovo N24 on resume becomes stuck in a state where it
sends incorrect packets, causing elantech_packet_check_v4 to fail.
The only way for the device to resume sending the correct packets is for
it to be disabled and then re-enabled.
This change adds a dmi check to trigger this behavior on resume.
Currently, worker ID formatting is open coded in create_worker(),
init_rescuer() and worker_thread() (for %WORKER_DIE case). The formatted ID
is saved into task->comm and wq_worker_comm() uses it as the base name to
append extra information to when generating the name to be shown to
userspace.
However, TASK_COMM_LEN is only 16 leading to badly truncated names for
rescuers. For example, the rescuer for the inet_frag_wq workqueue becomes:
Even for non-rescue workers, it's easy to run over 15 characters on
moderately large machines.
Fit it by consolidating worker ID formatting into a new helper
format_worker_id() and calling it from wq_worker_comm() to obtain the
untruncated worker ID string.
This is almost compatible, but passing a negative offset should result
in a EINVAL error, but on mips o32 compat mode would seek to a large
32-bit byte offset.
Use compat_sys_lseek() to correctly sign-extend the argument.
The ACPI IDs used in the CS35L56 HDA drivers are all handled by the
serial multi-instantiate driver which starts multiple Linux device
instances from a single ACPI Device() node.
As serial multi-instantiate is not an optional part of the system add it
as a dependency in Kconfig so that it is not overlooked.
[Why & How]
Current DRAM setting would cause underflow on customer platform.
Modify dram_clock_change_latency_us from 11.72 to 34.0 us as per recommendation from HW team
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com> Signed-off-by: Paul Hsieh <paul.hsieh@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Netlink flags, although they don't have payload at the netlink level,
are represented as having "True" as value in pyroute2.
Without it, trying to add a flow with a flag-type action (e.g: pop_vlan)
fails with the following traceback:
Traceback (most recent call last):
File "[...]/ovs-dpctl.py", line 2498, in <module>
sys.exit(main(sys.argv))
^^^^^^^^^^^^^^
File "[...]/ovs-dpctl.py", line 2487, in main
ovsflow.add_flow(rep["dpifindex"], flow)
File "[...]/ovs-dpctl.py", line 2136, in add_flow
reply = self.nlm_request(
^^^^^^^^^^^^^^^^^
File "[...]/pyroute2/netlink/nlsocket.py", line 822, in nlm_request
return tuple(self._genlm_request(*argv, **kwarg))
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
File "[...]/pyroute2/netlink/generic/__init__.py", line 126, in
nlm_request
return tuple(super().nlm_request(*argv, **kwarg))
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
File "[...]/pyroute2/netlink/nlsocket.py", line 1124, in nlm_request
self.put(msg, msg_type, msg_flags, msg_seq=msg_seq)
File "[...]/pyroute2/netlink/nlsocket.py", line 389, in put
self.sendto_gate(msg, addr)
File "[...]/pyroute2/netlink/nlsocket.py", line 1056, in sendto_gate
msg.encode()
File "[...]/pyroute2/netlink/__init__.py", line 1245, in encode
offset = self.encode_nlas(offset)
^^^^^^^^^^^^^^^^^^^^^^^^
File "[...]/pyroute2/netlink/__init__.py", line 1560, in encode_nlas
nla_instance.setvalue(cell[1])
File "[...]/pyroute2/netlink/__init__.py", line 1265, in setvalue
nlv.setvalue(nla_tuple[1])
~~~~~~~~~^^^
IndexError: list index out of range
Signed-off-by: Adrian Moreno <amorenoz@redhat.com> Acked-by: Aaron Conole <aconole@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Hardcoding the number of CPUs at compile time does improve code
generation, but if you get it wrong the result will be confusion.
We already limited this earlier to only "experts" (see commit fe5759d5bfda "cpumask: limit visibility of FORCE_NR_CPUS"), but with
distro kernel configs often having EXPERT enabled, that turns out to not
be much of a limit.
To quote the philosophers at Disney: "Everyone can be an expert. And
when everyone's an expert, no one will be".
There's a runtime warning if you then set nr_cpus to anything but the
forced number, but apparently that can be ignored too [1] and by then
it's pretty much too late anyway.
If we had some real way to limit this to "embedded only", maybe it would
be worth it, but let's see if anybody even notices that the option is
gone. We need to simplify kernel configuration anyway.
Link: https://lore.kernel.org/all/20240618105036.208a8860@rorschach.local.home/ Reported-by: Steven Rostedt <rostedt@goodmis.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Paul McKenney <paulmck@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Yury Norov <yury.norov@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Al reported a possible use-after-free (UAF) in kvm_spapr_tce_attach_iommu_group().
It looks up `stt` from tablefd, but then continues to use it after doing
fdput() on the returned fd. After the fdput() the tablefd is free to be
closed by another thread. The close calls kvm_spapr_tce_release() and
then release_spapr_tce_table() (via call_rcu()) which frees `stt`.
Although there are calls to rcu_read_lock() in
kvm_spapr_tce_attach_iommu_group() they are not sufficient to prevent
the UAF, because `stt` is used outside the locked regions.
With an artifcial delay after the fdput() and a userspace program which
triggers the race, KASAN detects the UAF:
Fix it by delaying the fdput() until `stt` is no longer in use, which
is effectively the entire function. To keep the patch minimal add a call
to fdput() at each of the existing return paths. Future work can convert
the function to goto or __cleanup style cleanup.
With the fix in place the test case no longer triggers the UAF.
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Closes: https://lore.kernel.org/all/20240610024437.GA1464458@ZenIV/ Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20240614122910.3499489-1-mpe@ellerman.id.au Signed-off-by: Sasha Levin <sashal@kernel.org>
Add support for this laptop, which uses CS35L41 HDA amps.
The laptop does not contain valid _DSD for these amps, so requires
entries into the CS35L41 configuration table to function correctly.
Add support for this laptop, which uses CS35L41 HDA amps.
The laptop does not contain valid _DSD for these amps, so requires
entries into the CS35L41 configuration table to function correctly.
[ fixed to lower hex numbers in quirk entries -- tiwai ]
In 'cfg80211_wext_siwscan()', add extra check whether number of
channels passed via 'ioctl(sock, SIOCSIWSCAN, ...)' doesn't exceed
IW_MAX_FREQUENCIES and reject invalid request with -EINVAL otherwise.
The codec should be cleared when the amp driver is unbound and when
resuming it should be tested to prevent loading firmware into the device
and ALSA in a partially configured system state.
If fallcate is implemented but zero and discard operations are not
supported by the filesystem the backing file is on we continue to fill
dmesg with errors from the blk_mq_end_request() since each time we call
fallocate() on the loop device the EOPNOTSUPP error from lo_fallocate()
ends up propagated into the block layer. In the end syscall succeeds
since the blkdev_issue_zeroout() falls back to writing zeroes which
makes the errors even more misleading and confusing.
How to reproduce:
1. make sure /tmp is mounted as tmpfs
2. dd if=/dev/zero of=/tmp/disk.img bs=1M count=100
3. losetup /dev/loop0 /tmp/disk.img
4. mkfs.ext2 /dev/loop0
5. dmesg |tail
[710690.898214] operation not supported error, dev loop0, sector 204672 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.898279] operation not supported error, dev loop0, sector 522 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.898603] operation not supported error, dev loop0, sector 16906 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.898917] operation not supported error, dev loop0, sector 32774 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.899218] operation not supported error, dev loop0, sector 49674 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.899484] operation not supported error, dev loop0, sector 65542 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.899743] operation not supported error, dev loop0, sector 82442 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.900015] operation not supported error, dev loop0, sector 98310 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.900276] operation not supported error, dev loop0, sector 115210 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.900546] operation not supported error, dev loop0, sector 131078 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
This patch changes the lo_fallocate() to clear the flags for zero and
discard operations if we get EOPNOTSUPP from the backing file fallocate
callback, that way we at least stop spewing errors after the first
unsuccessful try.
CC: Jan Kara <jack@suse.cz> Signed-off-by: Cyril Hrubis <chrubis@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20240613163817.22640-1-chrubis@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to improve performance of typical scenarios we can try to insert
the entire vma on fault. This accelerates typical cases, such as when
the MMIO region is DMA mapped by QEMU. The vfio_iommu_type1 driver will
fault in the entire DMA mapped range through fixup_user_fault().
In synthetic testing, this improves the time required to walk a PCI BAR
mapping from userspace by roughly 1/3rd.
This is likely an interim solution until vmf_insert_pfn_{pmd,pud}() gain
support for pfnmaps.
The spec doesn't mandate that the first two double words (aka results)
for the command queue entry need to be set to 0 when they are not
used (not specified). Though, the target implemention returns 0 for TCP
and FC but not for RDMA.
Let's make RDMA behave the same and thus explicitly initializing the
result field. This prevents leaking any data from the stack.
Signed-off-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a discard request needs to be retried, and that retry may fail before
a new special payload is added, a double free will result. Clear the
RQF_SPECIAL_LOAD when the request is cleaned.
Signed-off-by: Chunguang Xu <chunguang.xu@shopee.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Based on grepping through the source code this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown
time. Among other things, this means that if a panel is in use that it
won't be cleanly powered off at system shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart comes straight out of the kernel doc "driver
instance overview" in drm_drv.c.
This driver users the component model and shutdown happens in the base
driver. The "drvdata" for this driver will always be valid if
shutdown() is called and as of commit 2a073968289d
("drm/atomic-helper: drm_atomic_helper_shutdown(NULL) should be a
noop") we don't need to confirm that "drm" is non-NULL.
Based on grepping through the source code, this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown time.
This is important because drm_atomic_helper_shutdown() will cause
panels to get disabled cleanly which may be important for their power
sequencing. Future changes will remove any custom powering off in
individual panel drivers so the DRM drivers need to start getting this
right.
The fact that we should call drm_atomic_helper_shutdown() in the case of
OS shutdown comes straight out of the kernel doc "driver instance
overview" in drm_drv.c.
Core in platform_driver_register() already sets the .owner, so driver
does not need to. Whatever is set here will be anyway overwritten by
main driver calling platform_driver_register().
If the extent spans the block that contains i_size, we need to handle
both halves separately so that we properly zero data in the page cache
for blocks that are entirely outside of i_size. But this is needed only
when i_size is within the current folio under processing.
"orig_pos + length > isize" can be true for all folios if the mapped
extent length is greater than the folio size. That is making plen to
break for every folio instead of only the last folio.
So use orig_plen for checking if "orig_pos + orig_plen > isize".
Signed-off-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com> Link: https://lore.kernel.org/r/a32e5f9a4fcfdb99077300c4020ed7ae61d6e0f9.1715067055.git.ritesh.list@gmail.com Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Jan Kara <jack@suse.cz>
cc: Ojaswin Mujoo <ojaswin@linux.ibm.com> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As described in the added code comment, a reference to .exit.text is ok
for drivers registered via module_platform_driver_probe(). Make this
explicit to prevent the following section mismatch warning
Change level for the "not connected" client message in the write
callback from error to debug.
The MEI driver currently disconnects all clients upon system suspend.
This behavior is by design and user-space applications with
open connections before the suspend are expected to handle errors upon
resume, by reopening their handles, reconnecting,
and retrying their operations.
However, the current driver implementation logs an error message every
time a write operation is attempted on a disconnected client.
Since this is a normal and expected flow after system resume
logging this as an error can be misleading.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Link: https://lore.kernel.org/r/20240530091415.725247-1-tomas.winkler@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the vfio device fd tied to the address space of the pseudo fs
inode, we can use the mm to track all vmas that might be mmap'ing
device BARs, which removes our vma_list and all the complicated lock
ordering necessary to manually zap each related vma.
Note that we can no longer store the pfn in vm_pgoff if we want to use
unmap_mapping_range() to zap a selective portion of the device fd
corresponding to BAR mappings.
This also converts our mmap fault handler to use vmf_insert_pfn()
because we no longer have a vma_list to avoid the concurrency problem
with io_remap_pfn_range(). The goal is to eventually use the vm_ops
huge_fault handler to avoid the additional faulting overhead, but
vmf_insert_pfn_{pmd,pud}() need to learn about pfnmaps first.
Also, Jason notes that a race exists between unmap_mapping_range() and
the fops mmap callback if we were to call io_remap_pfn_range() to
populate the vma on mmap. Specifically, mmap_region() does call_mmap()
before it does vma_link_file() which gives a window where the vma is
populated but invisible to unmap_mapping_range().
Suggested-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Link: https://lore.kernel.org/r/20240530045236.1005864-3-alex.williamson@redhat.com Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
By linking all the device fds we provide to userspace to an
address space through a new pseudo fs, we can use tools like
unmap_mapping_range() to zap all vmas associated with a device.
Suggested-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Link: https://lore.kernel.org/r/20240530045236.1005864-2-alex.williamson@redhat.com Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The maximum possible return value of find_next_zero_bit(fdt->full_fds_bits,
maxbit, bitbit) is maxbit. This return value, multiplied by BITS_PER_LONG,
gives the value of bitbit, which can never be greater than maxfd, it can
only be equal to maxfd at most, so the following check 'if (bitbit > maxfd)'
will never be true.
Moreover, when bitbit equals maxfd, it indicates that there are no unused
fds, and the function can directly return.
Replacing wait_for_completion() with wait_for_completion_killable() in
cachefiles_ondemand_send_req() allows us to kill processes that might
trigger a hunk_task if the daemon is abnormal.
But now only CACHEFILES_OP_READ is killable, because OP_CLOSE and OP_OPEN
is initiated from kworker context and the signal is prohibited in these
kworker.
Note that when the req in xas changes, i.e. xas_load(&xas) != req, it
means that a process will complete the current request soon, so wait
again for the request to be completed.
In addition, add the cachefiles_ondemand_finish_req() helper function to
simplify the code.
Suggested-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Baokun Li <libaokun1@huawei.com> Link: https://lore.kernel.org/r/20240522114308.2402121-13-libaokun@huaweicloud.com Acked-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Jia Zhu <zhujia.zj@bytedance.com> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If copen is maliciously called in the user mode, it may delete the request
corresponding to the random id. And the request may have not been read yet.
Note that when the object is set to reopen, the open request will be done
with the still reopen state in above case. As a result, the request
corresponding to this object is always skipped in select_req function, so
the read request is never completed and blocks other process.
Fix this issue by simply set object to close if its id < 0 in copen.
Signed-off-by: Zizhi Wo <wozizhi@huawei.com> Signed-off-by: Baokun Li <libaokun1@huawei.com> Link: https://lore.kernel.org/r/20240522114308.2402121-11-libaokun@huaweicloud.com Acked-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Jia Zhu <zhujia.zj@bytedance.com> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This prevents malicious processes from completing random copen/cread
requests and crashing the system. Added checks are listed below:
* Generic, copen can only complete open requests, and cread can only
complete read requests.
* For copen, ondemand_id must not be 0, because this indicates that the
request has not been read by the daemon.
* For cread, the object corresponding to fd and req should be the same.
Signed-off-by: Baokun Li <libaokun1@huawei.com> Link: https://lore.kernel.org/r/20240522114308.2402121-7-libaokun@huaweicloud.com Acked-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a slight variation on a patch previously proposed by Neil Brown
that never got merged.
Prior to commit 5ceb9d7fdaaf ("NFS: Refactor nfs_lookup_revalidate()"),
any error from nfs_lookup_verify_inode() other than -ESTALE would result
in nfs_lookup_revalidate() returning that error (-ESTALE is mapped to
zero).
Since that commit, all errors result in nfs_lookup_revalidate()
returning zero, resulting in dentries being invalidated where they
previously were not (particularly in the case of -ERESTARTSYS).
Fix it by passing the actual error code to nfs_lookup_revalidate_done(),
and leaving the decision on whether to map the error code to zero or
one to nfs_lookup_revalidate_done().
A simple reproducer is to run the following python code in a
subdirectory of an NFS mount (not in the root of the NFS mount):
---8<---
import os
import multiprocessing
import time
if __name__=="__main__":
multiprocessing.set_start_method("spawn")
count = 0
while True:
try:
os.getcwd()
pool = multiprocessing.Pool(10)
pool.close()
pool.terminate()
count += 1
except Exception as e:
print(f"Failed after {count} iterations")
print(e)
break
---8<---
Prior to commit 5ceb9d7fdaaf, the above code would run indefinitely.
After commit 5ceb9d7fdaaf, it fails almost immediately with -ENOENT.
When we are doing WB_SYNC_ALL writeback, nfs submits write requests with
NFS_FILE_SYNC flag to the server (which then generally treats it as an
O_SYNC write). This helps to reduce latency for single requests but when
submitting more requests, additional fsyncs on the server side hurt
latency. NFS generally avoids this additional overhead by not setting
NFS_FILE_SYNC if desc->pg_moreio is set.
However this logic doesn't always work. When we do random 4k writes to a huge
file and then call fsync(2), each page writeback is going to be sent with
NFS_FILE_SYNC because after preparing one page for writeback, we start writing
back next, nfs_do_writepage() will call nfs_pageio_cond_complete() which finds
the page is not contiguous with previously prepared IO and submits is *without*
setting desc->pg_moreio. Hence NFS_FILE_SYNC is used resulting in poor
performance.
Fix the problem by setting desc->pg_moreio in nfs_pageio_cond_complete() before
submitting outstanding IO. This improves throughput of
fsync-after-random-writes on my test SSD from ~70MB/s to ~250MB/s.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is an inherent race where a symlink file may have been overriden
(by a different client) between lookup and readlink, resulting in a
spurious EIO error returned to userspace. Fix this by propagating back
ESTALE errors such that the vfs will retry the lookup/get_link (similar
to nfs4_file_open) at least once.
Cc: Dan Aloni <dan.aloni@vastdata.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
HUTRR94 added support for a new usage titled "System Do Not Disturb"
which toggles a system-wide Do Not Disturb setting. This commit simply
adds a new event code for the usage.
HUTRR116 added support for a new usage titled "System Accessibility
Binding" which toggles a system-wide bound accessibility UI or command.
This commit simply adds a new event code for the usage.
expr_trans_bool() performs an incorrect transformation.
[Test Code]
config MODULES
def_bool y
modules
config A
def_bool y
select C if B != n
config B
def_tristate m
config C
tristate
[Result]
CONFIG_MODULES=y
CONFIG_A=y
CONFIG_B=m
CONFIG_C=m
This output is incorrect because CONFIG_C=y is expected.
Documentation/kbuild/kconfig-language.rst clearly explains the function
of the '!=' operator:
If the values of both symbols are equal, it returns 'n',
otherwise 'y'.
Therefore, the statement:
select C if B != n
should be equivalent to:
select C if y
Or, more simply:
select C
Hence, the symbol C should be selected by the value of A, which is 'y'.
However, expr_trans_bool() wrongly transforms it to:
select C if B
Therefore, the symbol C is selected by (A && B), which is 'm'.
The comment block of expr_trans_bool() correctly explains its intention:
* bool FOO!=n => FOO
^^^^
If FOO is bool, FOO!=n can be simplified into FOO. This is correct.
However, the actual code performs this transformation when FOO is
tristate:
if (e->left.sym->type == S_TRISTATE) {
^^^^^^^^^^
While it can be fixed to S_BOOLEAN, there is no point in doing so
because expr_tranform() already transforms FOO!=n to FOO when FOO is
bool. (see the "case E_UNEQUAL" part)
The function run_all_insn_set_hw_mode() is registered as startup callback
of 'CPUHP_AP_ARM64_ISNDEP_STARTING', it invokes set_hw_mode() methods of
all emulated instructions.
As the STARTING callbacks are not expected to fail, if one of the
set_hw_mode() fails, e.g. due to el0 mixed-endian is not supported for
'setend', it will report a warning:
```
CPU[2] cannot support the emulation of setend
CPU 2 UP state arm64/isndep:starting (136) failed (-22)
CPU2: Booted secondary processor 0x0000000002 [0x414fd0c1]
```
To fix it, add a check for INSN_UNAVAILABLE status and skip the process.
The io_register_iowq_max_workers() function calls io_put_sq_data(),
which acquires the sqd->lock without releasing the uring_lock.
Similar to the commit 009ad9f0c6ee ("io_uring: drop ctx->uring_lock
before acquiring sqd->lock"), this can lead to a potential deadlock
situation.
To resolve this issue, the uring_lock is released before calling
io_put_sq_data(), and then it is re-acquired after the function call.
This change ensures that the locks are acquired in the correct
order, preventing the possibility of a deadlock.
As explained in commit 1378817486d6 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
Disabling preemption in rpl_output() is not good enough,
because rpl_output() is called from process context,
lwtunnel_output() only uses rcu_read_lock().
We might be interrupted by a softirq, re-enter rpl_output()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable() instead of
preempt_disable().
Apply a similar change in rpl_input().
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Alexander Aring <aahringo@redhat.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/20240531132636.2637995-3-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
HSMP interface is supported only on few x86 processors from AMD.
Accessing HSMP registers on rest of the platforms might cause
unexpected behaviour. So add a check.
Also unavailability of this interface on rest of the processors
is not an error. Hence, use pr_info() instead of the pr_err() to
log the message.
Signed-off-by: Suma Hegde <suma.hegde@amd.com> Reviewed-by: Naveen Krishna Chatradhi <naveenkrishna.chatradhi@amd.com> Link: https://lore.kernel.org/r/20240603081512.142909-1-suma.hegde@amd.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When support for Silead touchscreens was orginal added some touchscreens
with older firmware versions only supported 5 fingers and this was made
the default requiring the setting of a "silead,max-fingers=10" uint32
device-property for all touchscreen models which do support 10 fingers.
There are very few models with the old 5 finger fw, so in practice the
setting of the "silead,max-fingers=10" is boilerplate which needs to
be copy and pasted to every touchscreen config.
Reporting that 10 fingers are supported on devices which only support
5 fingers doesn't cause any problems for userspace in practice, since
at max 4 finger gestures are supported anyways. Drop the max_fingers
configuration and simply always assume 10 fingers.
The GMAC of Loongson chips cannot insert the correct 1.5-2ns delay. So
we need the PHY to insert internal delays for both transmit and receive
data lines from/to the PHY device. Fix this by changing the "phy-mode"
from "rgmii" to "rgmii-id" in dts.
In some scenarios, if too many commands are issued by nvme command in
the same time by user tasks, this may exhaust all tags of admin_q. If
a reset (nvme reset or IO timeout) occurs before these commands finish,
reconnect routine may fail to update nvme regs due to insufficient tags,
which will cause kernel hang forever. In order to workaround this issue,
maybe we can let reg_read32()/reg_read64()/reg_write32() use reserved
tags. This maybe safe for nvmf:
1. For the disable ctrl path, we will not issue connect command
2. For the enable ctrl / fw activate path, since connect and reg_xx()
are called serially.
So the reserved tags may still be enough while reg_xx() use reserved tags.
Factor out the parsing of interrupt-map interrupt parent phandle and its
arg cells to a separate function, of_irq_parse_imap_parent(), so that it
can be used in other parsing scenarios (e.g. fw_devlink).
There was a refcount leak on non-matching entries when iterating thru
"interrupt-map" which is fixed.
projects / linux / log