The W83L786NG stores the fan speed on 4 bits while the sysfs interface
uses a 0-255 range. Thus the driver should scale the user input down
to map it to the device range, and scale up the value read from the
device before presenting it to the user. The reserved register nibble
should be left unchanged.
Due to difficulty in arriving at the proper security label for
TCP SYN-ACK packets in selinux_ip_postroute(), we need to check packets
while/before they are undergoing XFRM transforms instead of waiting
until afterwards so that we can determine the correct security label.
Reported-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously selinux_skb_peerlbl_sid() would only check for labeled
IPsec security labels on inbound packets, this patch enables it to
check both inbound and outbound traffic for labeled IPsec security
labels.
Reported-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
E.g. landisk_defconfig, which has CONFIG_NTFS_FS=m:
ERROR: "__ashrdi3" [fs/ntfs/ntfs.ko] undefined!
For "lib-y", if no symbols in a compilation unit are referenced by other
units, the compilation unit will not be included in vmlinux. This
breaks modules that do reference those symbols.
This doesn't fix all cases. There are others, e.g. udivsi3.
This is also not limited to sh, many architectures handle this in the
same way.
A simple solution is to unconditionally include all helper functions.
A more complex solution is to make the choice of "lib-y" or "obj-y" depend
on CONFIG_MODULES:
throttle_cfs_rq() doesn't check to make sure that period_timer is running,
and while update_curr/assign_cfs_runtime does, a concurrently running
period_timer on another cpu could cancel itself between this cpu's
update_curr and throttle_cfs_rq(). If there are no other cfs_rqs running
in the tg to restart the timer, this causes the cfs_rq to be stranded
forever.
Fix this by calling __start_cfs_bandwidth() in throttle if the timer is
inactive.
(Also add some sched_debug lines for cfs_bandwidth.)
Tested: make a run/sleep task in a cgroup, loop switching the cgroup
between 1ms/100ms quota and unlimited, checking for timer_active=0 and
throttled=1 as a failure. With the throttle_cfs_rq() change commented out
this fails, with the full patch it passes.
Signed-off-by: Ben Segall <bsegall@google.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: pjt@google.com Link: http://lkml.kernel.org/r/20131016181632.22647.84174.stgit@sword-of-the-dawn.mtv.corp.google.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Chris J Arges <chris.j.arges@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should be writing bits here but instead we're writing the
numbers that correspond to the bits we want to write. Fix it by
wrapping the numbers in the BIT() macro. This fixes gpios acting
as interrupts.
If a handle runs out of space, we currently stop the kernel with a BUG
in jbd2_journal_dirty_metadata(). This makes it hard to figure out
what might be going on. So return an error of ENOSPC, so we can let
the file system layer figure out what is going on, to make it more
likely we can get useful debugging information). This should make it
easier to debug problems such as the one which was reported by:
https://bugzilla.kernel.org/show_bug.cgi?id=44731
The only two callers of this function are ext4_handle_dirty_metadata()
and ocfs2_journal_dirty(). The ocfs2 function will trigger a
BUG_ON(), which means there will be no change in behavior. The ext4
function will call ext4_error_inode() which will print the useful
debugging information and then handle the situation using ext4's error
handling mechanisms (i.e., which might mean halting the kernel or
remounting the file system read-only).
Also, since both file systems already call WARN_ON(), drop the WARN_ON
from jbd2_journal_dirty_metadata() to avoid two stack traces from
being displayed.
In patch 209806aba9d540dde3db0a5ce72307f85f33468f we allowed
local deferred locks to be granted against a cached exclusive
lock. That opened up a corner case which this patch now
fixes.
The solution to the problem is to check whether we have cached
pages each time we do direct I/O and if so to unmap, flush
and invalidate those pages. Since the glock state machine
normally does that for us, mostly the code will be a no-op.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to make sure we allocate absinfo data when we are setting one of
EV_ABS/ABS_XXX capabilities, otherwise we may bomb when we try to emit this
event.
On Fedora systems, unloading rtl8192ce causes an oops. This patch fixes the
problem reported at https://bugzilla.redhat.com/show_bug.cgi?id=852761.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Evan Huus found (by fuzzing in wireshark) that the radiotap
iterator code can access beyond the length of the buffer if
the first bitmap claims an extension but then there's no
data at all. Fix this.
We've received multiple reports in Fedora via (BZ 907193)
that the Seagate Momentus SpinPoint M8 errors out when enabling AA:
[ 2.555905] ata2.00: failed to enable AA (error_mask=0x1)
[ 2.568482] ata2.00: failed to enable AA (error_mask=0x1)
Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk.
Reported-by: Nicholas <arealityfarbetween@googlemail.com> Signed-off-by: Michele Baldessari <michele@acksyn.org> Tested-by: Nicholas <arealityfarbetween@googlemail.com> Acked-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a user calls 'cpupower set --perf-bias 15', the process will end with
a SIGSEGV in libc because cpupower-set passes a NULL optarg to the atoi
call. This is because the getopt_long structure currently has all of
the options as having an optional_argument when they really have a
required argument. We change the structure to use required_argument to
match the short options and it resolves the issue.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=1000439
p_end is an 8 byte value embedded in the text section. This means it
is only 4 byte aligned when it should be 8 byte aligned. Fix this
by adding an explicit alignment.
This fixes an issue where POWER7 little endian builds with
CONFIG_RELOCATABLE=y fail to boot.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In EXCEPTION_PROLOG_COMMON() we check to see if the stack pointer (r1)
is valid when coming from the kernel. If it's not valid, we die but
with a nice oops message.
Currently we allocate a stack frame (subtract INT_FRAME_SIZE) before we
check to see if the stack pointer is negative. Unfortunately, this
won't detect a bad stack where r1 is less than INT_FRAME_SIZE.
This patch fixes the check to compare the modified r1 with
-INT_FRAME_SIZE. With this, bad kernel stack pointers (including NULL
pointers) are correctly detected again.
Kudos to Paulus for finding this.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pick the MAC address of the first virtual interface as the new hardware MAC
address. Set BSSID mask according to this MAC address. This fixes CVE-2013-4579.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a driver workaround for a HW issue.
A race condition in the HW results in missing interrupts,
which can be avoided by a read/write with the ISR register.
All chips in the AR9002 series are affected by this bug - AR9003
and above do not have this problem.
Cc: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Certain dm962x revisions contain an bug, where if a USB bulk transfer retry
(E.G. if bulk crc mismatch) happens right after a transfer with odd or
maxpacket length, the internal tx hardware fifo gets out of sync causing
the interface to stop working.
Work around it by adding up to 3 bytes of padding to ensure this situation
cannot trigger.
This workaround also means we never pass multiple-of-maxpacket size skb's
to usbnet, so the length adjustment to handle usbnet's padding of those can
be removed.
Reported-by: Joseph Chang <joseph_chang@davicom.com.tw> Signed-off-by: Peter Korsgaard <peter@korsgaard.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dm9620/dm9621a require room for 4 byte padding even in dm9601 (3 byte
header) mode.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the length of data to be read in readpage() is exactly
PAGE_CACHE_SIZE, the original code does not flush d-cache
for data consistency after finishing reading. This patches fixes
this.
Signed-off-by: Li Wang <liwang@ubuntukylin.com> Signed-off-by: Sage Weil <sage@inktank.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...the problem is that the receive path falls back to cpu-copy in
several locations and this trace is just one of the areas. A few
options were considered to fix this:
1/ sync all dma whenever a cpu copy branch is taken
2/ modify the page fault handler to hold off while dma is in-flight
Option 1 adds yet more cpu overhead to an "offload" that struggles to compete
with cpu-copy. Option 2 adds checks for behavior that is already documented as
broken when using get_user_pages(). At a minimum a debug mode is warranted to
catch and flag these violations of the dma-api vs get_user_pages().
Thanks to David for his reproducer.
Cc: Dave Jiang <dave.jiang@intel.com> Cc: Vinod Koul <vinod.koul@intel.com> Cc: Alexander Duyck <alexander.h.duyck@intel.com> Reported-by: David Whipple <whipple@securedatainnovations.ch> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Functions inc_rt_prio_smp() and dec_rt_prio_smp() change (global) rq's
priority, while rt_rq passed to them may be not the top-level rt_rq.
This is wrong, because changing of priority on a child level does not
guarantee that the priority is the highest all over the rq. So, this
leak makes RT balancing unusable.
The short example: the task having the highest priority among all rq's
RT tasks (no one other task has the same priority) are waking on a
throttle rt_rq. The rq's cpupri is set to the task's priority
equivalent, but real rq->rt.highest_prio.curr is less.
A corrupted ext4 may have out of order leaf extents, i.e.
extent: lblk 0--1023, len 1024, pblk 9217, flags: LEAF UNINIT
extent: lblk 1000--2047, len 1024, pblk 10241, flags: LEAF UNINIT
^^^^ overlap with previous extent
Reading such extent could hit BUG_ON() in ext4_es_cache_extent().
BUG_ON(end < lblk);
The problem is that __read_extent_tree_block() tries to cache holes as
well but assumes 'lblk' is greater than 'prev' and passes underflowed
length to ext4_es_cache_extent(). Fix it by checking for overlapping
extents in ext4_valid_extent_entries().
I hit this when fuzz testing ext4, and am able to reproduce it by
modifying the on-disk extent by hand.
Also add the check for (ee_block + len - 1) in ext4_valid_extent() to
make sure the value is not overflow.
ext4_mb_put_pa should hold pa->pa_lock before accessing pa->pa_count.
While ext4_mb_use_preallocated checks pa->pa_deleted first and then
increments pa->count later, ext4_mb_put_pa decrements pa->pa_count
before holding pa->pa_lock and then sets pa->pa_deleted.
* Free sequence
ext4_mb_put_pa (1): atomic_dec_and_test pa->pa_count
ext4_mb_put_pa (2): lock pa->pa_lock
ext4_mb_put_pa (3): check pa->pa_deleted
ext4_mb_put_pa (4): set pa->pa_deleted=1
ext4_mb_put_pa (5): unlock pa->pa_lock
ext4_mb_put_pa (6): remove pa from a list
ext4_mb_pa_callback: free pa
* Use sequence
ext4_mb_use_preallocated (1): iterate over preallocation
ext4_mb_use_preallocated (2): lock pa->pa_lock
ext4_mb_use_preallocated (3): check pa->pa_deleted
ext4_mb_use_preallocated (4): increase pa->pa_count
ext4_mb_use_preallocated (5): unlock pa->pa_lock
ext4_mb_release_context: access pa
Ftrace currently initializes only the online CPUs. This implementation has
two problems:
- If we online a CPU after we enable the function profile, and then run the
test, we will lose the trace information on that CPU.
Steps to reproduce:
# echo 0 > /sys/devices/system/cpu/cpu1/online
# cd <debugfs>/tracing/
# echo <some function name> >> set_ftrace_filter
# echo 1 > function_profile_enabled
# echo 1 > /sys/devices/system/cpu/cpu1/online
# run test
- If we offline a CPU before we enable the function profile, we will not clear
the trace information when we enable the function profile. It will trouble
the users.
Steps to reproduce:
# cd <debugfs>/tracing/
# echo <some function name> >> set_ftrace_filter
# echo 1 > function_profile_enabled
# run test
# cat trace_stat/function*
# echo 0 > /sys/devices/system/cpu/cpu1/online
# echo 0 > function_profile_enabled
# echo 1 > function_profile_enabled
# cat trace_stat/function*
# run test
# cat trace_stat/function*
So it is better that we initialize the ftrace profiler for each possible cpu
every time we enable the function profile instead of just the online ones.
selinux_setprocattr() does ptrace_parent(p) under task_lock(p),
but task_struct->alloc_lock doesn't pin ->parent or ->ptrace,
this looks confusing and triggers the "suspicious RCU usage"
warning because ptrace_parent() does rcu_dereference_check().
And in theory this is wrong, spin_lock()->preempt_disable()
doesn't necessarily imply rcu_read_lock() we need to access
the ->parent.
Reported-by: Evan McNabb <emcnabb@redhat.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a broken networking check. Return an error if peer recv fails. If
secmark is active and the packet recv succeeds the peer recv error is
ignored.
Signed-off-by: Chad Hanson <chanson@trustedcs.com> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the process is sleeping at the SNDRV_PCM_STATE_PAUSED
state from the wait_for_avail function, the sleep process will be woken by
timeout(10 seconds). Even if the sleep process wake up by timeout, by this
patch, the process will continue with sleep and wait for the other state.
When wm8904 work in DSP mode B, we still need to configure it to
work in DSP mode. Or else, it will work in Right Justified mode.
Signed-off-by: Bo Shen <voice.shen@atmel.com> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since kvmppc_hv_find_lock_hpte() is called from both virtmode and
realmode, so it can trigger the deadlock.
Suppose the following scene:
Two physical cpuM, cpuN, two VM instances A, B, each VM has a group of
vcpus.
If on cpuM, vcpu_A_1 holds bitlock X (HPTE_V_HVLOCK), then is switched
out, and on cpuN, vcpu_A_2 try to lock X in realmode, then cpuN will be
caught in realmode for a long time.
What makes things even worse if the following happens,
On cpuM, bitlockX is hold, on cpuN, Y is hold.
vcpu_B_2 try to lock Y on cpuM in realmode
vcpu_A_2 try to lock X on cpuN in realmode
Oops! deadlock happens
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com> Reviewed-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aborted requests usually get cleared when the reply is received.
If MDS crashes, no reply will be received. So we need to cleanup
aborted requests when re-sending requests.
Fix race in generic write implementation, which could lead to
temporarily degraded throughput.
The current generic write implementation introduced by commit 27c7acf22047 ("USB: serial: reimplement generic fifo-based writes") has
always had this bug, although it's fairly hard to trigger and the
consequences are not likely to be noticed.
Specifically, a write() on one CPU while the completion handler is
running on another could result in only one of the two write urbs being
utilised to empty the remainder of the write fifo (unless there is a
second write() that doesn't race during that time).
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In _ocp_softreset(), after _set_softreset() + write_sysconfig(),
the hwmod's sysc_cache will always contain SOFTRESET bit set
so all further writes to sysconfig using this cache will initiate
a repeated SOFTRESET e.g. enable_sysc(). This is true for OMAP3 like
platforms that have RESET_DONE status in the SYSSTATUS register and
so the the SOFTRESET bit in SYSCONFIG is not automatically cleared.
It is not a problem for OMAP4 like platforms that indicate RESET
completion by clearing the SOFTRESET bit in the SYSCONFIG register.
This repeated SOFTRESET is undesired and was the root cause of
USB host issues on OMAP3 platforms when hwmod was allowed to do the
SOFTRESET for the USB Host module.
To fix this we clear the SOFTRESET bit and update the sysconfig
register + sysc_cache using write_sysconfig().
Signed-off-by: Roger Quadros <rogerq@ti.com> Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
[paul@pwsan.com: renamed _clr_softreset() to _clear_softreset()] Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Veaceslav Falico <veaceslav@falico.eu> Cc: David S. Miller <davem@davemloft.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Richard Weinberger <richard@nod.at> Cc: Shawn Landden <shawnlandden@gmail.com> Cc: Tom Herbert <therbert@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If loaded with isapnp = 0 the driver explodes. This is catching
people out now and then. What should happen in the working case is
a complete mystery and the code appears terminally confused, but we
can at least make the error path work properly.
Signed-off-by: Alan Cox <alan@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Partially-Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=53991 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pcmuio_detach() is called by the comedi core even if pcmuio_attach()
returned an error, so `dev->private` might be `NULL`. Check for that
before dereferencing it.
Also, as pointed out by Dan Carpenter, there is no need to check the
pointer passed to `kfree()` is non-NULL, so remove that check.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Cc: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When compiling a 32bit kernel with CONFIG_LBDAF=n the compiler complains like
shown below. Fix this warning by instead using sector_div() which is provided
by the kernel.h header file.
fs/nfs/blocklayout/extents.c: In function ‘normalize’:
include/asm-generic/div64.h:43:28: warning: comparison of distinct pointer types lacks a cast [enabled by default]
fs/nfs/blocklayout/extents.c:47:13: note: in expansion of macro ‘do_div’
nfs/blocklayout/extents.c:47:2: warning: right shift count >= width of type [enabled by default]
fs/nfs/blocklayout/extents.c:47:2: warning: passing argument 1 of ‘__div64_32’ from incompatible pointer type [enabled by default]
include/asm-generic/div64.h:35:17: note: expected ‘uint64_t *’ but argument is of type ‘sector_t *’
extern uint32_t __div64_32(uint64_t *dividend, uint32_t divisor);
The dm_round_up function may overflow to zero. In this case,
dm_table_create() must fail rather than go on to allocate an empty array
with alloc_targets().
This fixes a possible memory corruption that could be caused by passing
too large a number in "param->target_count".
The dm-delay target uses a shared workqueue for multiple instances. This
can cause deadlock if two or more dm-delay targets are stacked on the top
of each other.
This patch changes dm-delay to use a per-instance workqueue.
Some module parameters in dm-bufio are read-only. These parameters
inform the user about memory consumption. They are not supposed to be
changed by the user.
However, despite being read-only, these parameters can be set on
modprobe or insmod command line, for example:
modprobe dm-bufio current_allocated_bytes=12345
The kernel doesn't expect that these variables can be non-zero at module
initialization and if the user sets them, it results in BUG.
This patch initializes the variables in the module init routine, so that
user-supplied values are ignored.
UEFI time services are often broken once we're in virtual mode. We were
already refusing to use them on 64-bit systems, but it turns out that
they're also broken on some 32-bit firmware, including the Dell Venue.
Disable them for now, we can revisit once we have the 1:1 mappings code
incorporated.
Some boards seem to have garbage in the upper
16 bits of the vram size register. Check for
this and clamp the size properly. Fixes
boards reporting bogus amounts of vram.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Multicast frames can't be transmitted as part of an aggregation
session (such a session couldn't even be set up) so don't try to
reorder them. Trying to do so would cause the reorder to stop
working correctly since multicast QoS frames (as transmitted by
the Aruba APs this was found with) would cause sequence number
confusion in the buffer.
In selinux_ip_postroute() we perform access checks based on the
packet's security label. For locally generated traffic we get the
packet's security label from the associated socket; this works in all
cases except for TCP SYN-ACK packets. In the case of SYN-ACK packet's
the correct security label is stored in the connection's request_sock,
not the server's socket. Unfortunately, at the point in time when
selinux_ip_postroute() is called we can't query the request_sock
directly, we need to recreate the label using the same logic that
originally labeled the associated request_sock.
See the inline comments for more explanation.
Reported-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Tested-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In selinux_ip_output() we always label packets based on the parent
socket. While this approach works in almost all cases, it doesn't
work in the case of TCP SYN-ACK packets when the correct label is not
the label of the parent socket, but rather the label of the larval
socket represented by the request_sock struct.
Unfortunately, since the request_sock isn't queued on the parent
socket until *after* the SYN-ACK packet is sent, we can't lookup the
request_sock to determine the correct label for the packet; at this
point in time the best we can do is simply pass/NF_ACCEPT the packet.
It must be said that simply passing the packet without any explicit
labeling action, while far from ideal, is not terrible as the SYN-ACK
packet will inherit any IP option based labeling from the initial
connection request so the label *should* be correct and all our
access controls remain in place so we shouldn't have to worry about
information leaks.
Reported-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Tested-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch supports the separate handling of the USB transfer buffer length
and the length of the buffer used for multi packet support. For devices
supporting multiple report or diagnostic packets, the USB transfer size is now
limited to the USB endpoints wMaxPacketSize - otherwise it defaults to the
configured report packet size as before.
This fixes an issue where event reporting can be delayed for an arbitrary
time for multi packet devices. For instance the report size for eGalax devices
is defined to the 16 byte maximum diagnostic packet size as opposed to the 5
byte report packet size. In case the driver requests 16 byte from the USB
interrupt endpoint, the USB host controller driver needs to split up the
request into 2 accesses according to the endpoints wMaxPacketSize of 8 byte.
When the first transfer is answered by the eGalax device with not less than
the full 8 byte requested, the host controller has got no way of knowing
whether the touch controller has got additional data queued and will issue
the second transfer. If per example a liftoff event finishes at such a
wMaxPacketSize boundary, the data will not be available to the usbtouch driver
until a further event is triggered and transfered to the host. From user
perspective the BTN_TOUCH release event in this case is stuck until the next
touch down event.
The delayed_status value is used to keep track of status response
packets on ep0. It needs to be reset or the set_config function would
still delay the answer, if the usb device got unplugged while waiting
for setup_continue to be called.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3 UDC driver doesn't implement endpoint wedging correctly.
When an endpoint is wedged, the gadget driver should be allowed to
clear the wedge by calling usb_ep_clear_halt(). Only the host is
prevented from resetting the endpoint.
This patch fixes the implementation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Pratyush Anand <pratyush.anand@st.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a check for USB_STATE_NOTATTACHED to the
hub_port_warm_reset_required() workaround for ports that end up in
Compliance Mode in hub_events() when trying to decide which reset
function to use. Trying to call usb_reset_device() with a NOTATTACHED
device will just fail and leave the port broken.
Signed-off-by: Julius Werner <jwerner@chromium.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hugepage code had the exact same bug that regular pages had in
commit 7485d0d3758e ("futexes: Remove rw parameter from
get_futex_key()").
The regular page case was fixed by commit 9ea71503a8ed ("futex: Fix
regression with read only mappings"), but the transparent hugepage case
(added in a5b338f2b0b1: "thp: update futex compound knowledge") case
remained broken.
Found by Dave Jones and his trinity tool.
Reported-and-tested-by: Dave Jones <davej@fedoraproject.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Mel Gorman <mgorman@suse.de> Cc: Darren Hart <dvhart@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In multiple functions the vcpu_id is used as an offset into a bitfield. Ag
malicious user could specify a vcpu_id greater than 255 in order to set or
clear bits in kernel memory. This could be used to elevate priveges in the
kernel. This patch verifies that the vcpu_id provided is less than 255.
The api documentation already specifies that the vcpu_id must be less than
max_vcpus, but this is currently not checked.
Reported-by: Andrew Honig <ahonig@google.com> Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes corner case when (fp + 4) overflows unsigned long,
for example: fp = 0xFFFFFFFF -> fp + 4 == 3.
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_wchan() is lockless. Task may wakeup at any time and change its own stack,
thus each next stack frame may be overwritten and filled with random stuff.
/proc/$pid/stack interface had been disabled for non-current tasks, see [1]
But 'wchan' still allows to trigger stack frame unwinding on volatile stack.
This patch fixes oops in unwind_frame() by adding stack pointer validation on
each step (as x86 code do), unwind_frame() already checks frame pointer.
Also I've found another report of this oops on stackoverflow (irony).
Unlike what the comment states, errata i660 does not state that we
can't RESET the USB host module. Instead it states that RESET is the
only way to recover from a deadlock situation.
RESET ensures that the module is in a known good state irrespective
of what bootloader does with the module, so it must be done at boot.
Signed-off-by: Roger Quadros <rogerq@ti.com> Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM Fixes: de231388cb80 ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3") Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When converting from tosa-keyboard driver to matrix keyboard, tosa keys
received extra 1 column shift. Replace that with correct values to make
keyboard work again.
Fixes: f69a6548c9d5 ('[ARM] pxa/tosa: make use of the matrix keypad driver') Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running a 32bit kernel the hda_intel driver is still reporting
a 64bit dma_mask if the HW supports it.
From sound/pci/hda/hda_intel.c:
/* allow 64bit DMA address if supported by H/W */
if ((gcap & ICH6_GCAP_64OK) && !pci_set_dma_mask(pci, DMA_BIT_MASK(64)))
pci_set_consistent_dma_mask(pci, DMA_BIT_MASK(64));
else {
pci_set_dma_mask(pci, DMA_BIT_MASK(32));
pci_set_consistent_dma_mask(pci, DMA_BIT_MASK(32));
}
which means when there is a call to dma_alloc_coherent from
snd_malloc_dev_pages a machine address bigger than 32bit can be returned.
This can be true in particular if running the 32bit kernel as a pv dom0
under the Xen Hypervisor or PAE on bare metal.
The problem is that when calling setup_bdle to program the BLE the
dma_addr_t returned from the dma_alloc_coherent is wrongly truncated
from snd_sgbuf_get_addr if running a 32bit kernel:
where PAGE_MASK in a 32bit kernel is zeroing the upper 32bit af addr.
Without this patch the HW will fetch the 32bit truncated address,
which is not the one obtained from dma_alloc_coherent and will result
to a non working audio but can corrupt host memory at a random location.
The BMIPS5000 (Zephyr) processor utilizes instruction speculation. A
stale misprediction address in either the JTB or the CRS may trigger
a prefetch inside a region that is currently being used by a DMA engine,
which is not IO-coherent. This prefetch will fetch a line into the
scache, and that line will soon become stale (ie wrong) during/after the
DMA. Mayhem ensues.
In dma-default.c, the r10000 is handled as a special case in the same way
that we want to handle Zephyr. So we generalize the exception cases into
a function, and include Zephyr as one of the processors that needs this
special care.
Now that scatterwalk_sg_chain sets the chain pointer bit the sg_page
call in scatterwalk_sg_next hits a BUG_ON when CONFIG_DEBUG_SG is
enabled. Use sg_chain_ptr instead of sg_page on a chain entry.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the CS5 setting on the PL2303 USB-to-serial devices. CS5 has a
value of 0 and the CSIZE setting has been skipped altogether by the enclosing
if. Tested on 3.11.6 and the scope shows the correct output after the fix has
been applied.
Tagged to be added to stable, because it fixes a user visible driver bug and is
simple enough to backport easily.
Signed-off-by: Colin Leitner <colin.leitner@gmail.com> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arch/um/os-Linux/start_up.c: In function 'check_coredump_limit':
arch/um/os-Linux/start_up.c:338:16: error: storage size of 'lim' isn't known
arch/um/os-Linux/start_up.c:339:2: error: implicit declaration of function 'getrlimit' [-Werror=implicit-function-declaration]
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org> CC: Jeff Dike <jdike@addtoit.com> CC: Richard Weinberger <richard@nod.at> CC: Al Viro <viro@zeniv.linux.org.uk> CC: user-mode-linux-devel@lists.sourceforge.net CC: user-mode-linux-user@lists.sourceforge.net CC: linux-kernel@vger.kernel.org Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moust (if not all) modern software, including X, uses /dev/eventX rather than
the legacy /dev/mouseX devices. It therefore makes sense for general-purpose
(distro) kernels to use MOUSEDV=m (or even n), so let's drop the EXPERT=y
requirement.
There is plenty of consumer hardware (e.g., mac books) that does not use AT
keyboards or PS/2 mice. It therefore makes sense for distro kernels to
build the related drivers as modules to avoid loading them on hardware that
does not need them. As such, these options should no longer be protected by
EXPERT.
Moreover, building these drivers as modules gets rid of the following ugly
error during boot:
[ 2.337745] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 3.439537] i8042: No controller found
Commit 35f9c09fe (tcp: tcp_sendpages() should call tcp_push() once)
added an internal flag MSG_SENDPAGE_NOTLAST, similar to
MSG_MORE.
algif_hash, algif_skcipher, and udp used MSG_MORE from tcp_sendpages()
and need to see the new flag as identical to MSG_MORE.
This fixes sendfile() on AF_ALG.
v3: also fix udp
Cc: Tom Herbert <therbert@google.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: David S. Miller <davem@davemloft.net> Reported-and-tested-by: Shawn Landden <shawnlandden@gmail.com>
Original-patch: Richard Weinberger <richard@nod.at> Signed-off-by: Shawn Landden <shawn@churchofgit.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the system enters suspend, it disables all interrupts in
suspend_device_irqs(), including the interrupts marked EARLY_RESUME.
On the resume side things are different. The EARLY_RESUME interrupts
are reenabled in sys_core_ops->resume and the non EARLY_RESUME
interrupts are reenabled in the normal system resume path.
When suspend_noirq() failed or suspend is aborted for any other
reason, we might omit the resume side call to sys_core_ops->resume()
and therefor the interrupts marked EARLY_RESUME are not reenabled and
stay disabled forever.
To solve this, enable all irqs unconditionally in irq_resume()
regardless whether interrupts marked EARLY_RESUMEhave been already
enabled or not.
This might try to reenable already enabled interrupts in the non
failure case, but the only affected platform is XEN and it has been
confirmed that it does not cause any side effects.
For MPC8572/MPC8536, the status of GPIOs defined as output
cannot be determined by reading GPDAT register, so the code
use shadow data register instead. But the code may give the
wrong status of GPIOs defined as input under some scenarios:
1. If some pins were configured as inputs and were asserted
high before booting the kernel, the shadow data has been
initialized with those pin values.
2. Some pins have been configured as output first and have
been set to the high value, then reconfigured as input.
The above cases will make the shadow data for those input
pins to be set to high. Then reading the pin status will
always return high even if the actual pin status is low.
The code should eliminate the effects of the shadow data to
the input pins, and the status of those pins should be
read directly from GPDAT.
Acked-by: Scott Wood <scottwood@freescale.com> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit e9e4ea74f06635f2ffc1dffe5ef40c854faa0a90
"net: smc91x: dont't use SMC_outw for fixing up halfword-aligned data"
The Versatile SMSC LAN91C111 is crashing like this:
This is because the macro operations in smc91x.h defined
for Versatile are missing SMC_outsw() as used in this
commit.
The Versatile needs and uses the same accessors as the other
platforms in the first if(...) clause, just switch it to using
that and we have one problem less to worry about.
This includes a hunk of a patch from Will Deacon fixin
the other 32bit platforms as well: Innokom, Ramses, PXA,
PCM027.
Checkpatch complains about spacing, but I have opted to
follow the style of this .h-file.
Cc: Russell King <linux@arm.linux.org.uk> Cc: Nicolas Pitre <nico@fluxnic.net> Cc: Eric Miao <eric.y.miao@gmail.com> Cc: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A return value of 1 is interpreted as an error. See pci_driver.
in local_pci_probe(). If you're wondering how this ever could
have worked, it's because it used to be the case that only return
values less than zero were interpreted as failure. But even in
the current kernel if the driver registers its various entry
points with the kernel, and then returns a value which is
interpreted as failure, those registrations aren't undone, so
the driver still mostly works. However, the driver's remove
function wouldn't be called on rmmod, and pci power management
functions wouldn't work. In the case of Smart Array, since it
has a battery backed cache (or else no cache) even if the driver
is not shut down properly as long as there is no outstanding
i/o, nothing too bad happens, which is why it took so long to
notice.
Requesting backport to stable because the change to pci-driver.c
which requires driver probe functions to return 0 occurred between
2.6.35 and 2.6.36 (the pci power management breakage) and again
between 3.7 and 3.8 (pci_dev->driver getting set to NULL in
local_pci_probe() preventing driver remove function from being
called on rmmod.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We inadvertantly discarded the scsi status for aborted commands.
For some commands (e.g. reads from tape drives) these can't be retried,
and if we discarded the scsi status, the scsi mid layer couldn't notice
anything was wrong and the error was not reported.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 110dd8f19df5 "[SCSI] libsas: fix scr_read/write users and
update the libata documentation" we have been passing pmp=1 and is_cmd=0
to ata_tf_to_fis(). Praveen reports that eSATA attached drives do not
discover correctly. His investigation found that the BIOS was passing
pmp=0 while Linux was passing pmp=1 and failing to discover the drives.
Update libsas to follow the libata example of pulling the pmp setting
from the ata_link and correct is_cmd to be 1 since all tf's submitted
through ->qc_issue are commands. Presumably libsas lldds do not care
about is_cmd as they have sideband mechanisms to perform link
management.
The issue is happened in dual controller configuration. We got the
sysfs warnings when rmmod the ipr module.
enclosure_unregister() in drivers/msic/enclosure.c, call device_unregister()
for each componment deivce, device_unregister() ->device_del()->kobject_del()
->sysfs_remove_dir(). In sysfs_remove_dir(), set kobj->sd = NULL.
For each componment device,
enclosure_component_release()->enclosure_remove_links()->sysfs_remove_link()
in which checking kobj->sd again, it has been set as NULL when doing
device_unregister. So we saw all these sysfs WARNING.
Tested-by: wenxiong@linux.vnet.ibm.com Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to WM8731 "PD, Rev 4.9 October 2012" datasheet, when it
works in DSP mode A, LRP = 1, while works in DSP mode B, LRP = 0.
So, fix LRP for DSP mode as the datesheet specification.
Signed-off-by: Bo Shen <voice.shen@atmel.com> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mark Brown <broonie@linaro.org> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux / log