We didn't check length of rock ridge ER records before printing them.
Thus corrupted isofs image can cause us to access and print some memory
behind the buffer with obvious consequences.
Reported-and-tested-by: Carl Henrik Lunde <chlunde@ping.uio.no> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back when audio was enabled, the muxing of some MPP pins was causing
problems. However, since commit fea038ed55ae ("ARM: mvebu: Add proper
pin muxing on the Armada 370 DB board"), those problematic MPP pins
have been assigned a proper muxing for the Ethernet interfaces. This
proper muxing is now conflicting with the hog pins muxing that had
been added as part of 249f3822509b ("ARM: mvebu: add audio support to
Armada 370 DB").
Therefore, this commit simply removes the hog pins muxing, which
solves a warning a boot time due to the conflicting muxing
requirements.
Fixes: fea038ed55ae ("ARM: mvebu: Add proper pin muxing on the Armada 370 DB board") Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Link: https://lkml.kernel.org/r/1414512524-24466-5-git-send-email-thomas.petazzoni@free-electrons.com Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling the hardware I/O coherency on Armada 370, Armada 375, Armada
38x and Armada XP requires a certain number of conditions:
- On Armada 370, the cache policy must be set to write-allocate.
- On Armada 375, 38x and XP, the cache policy must be set to
write-allocate, the pages must be mapped with the shareable
attribute, and the SMP bit must be set
Currently, on Armada XP, when CONFIG_SMP is enabled, those conditions
are met. However, when Armada XP is used in a !CONFIG_SMP kernel, none
of these conditions are met. With Armada 370, the situation is worse:
since the processor is single core, regardless of whether CONFIG_SMP
or !CONFIG_SMP is used, the cache policy will be set to write-back by
the kernel and not write-allocate.
Since solving this problem turns out to be quite complicated, and we
don't want to let users with a mainline kernel known to have
infrequent but existing data corruptions, this commit proposes to
simply disable hardware I/O coherency in situations where it is known
not to work.
And basically, the is_smp() function of the kernel tells us whether it
is OK to enable hardware I/O coherency or not, so this commit slightly
refactors the coherency_type() function to return
COHERENCY_FABRIC_TYPE_NONE when is_smp() is false, or the appropriate
type of the coherency fabric in the other case.
Thanks to this, the I/O coherency fabric will no longer be used at all
in !CONFIG_SMP configurations. It will continue to be used in
CONFIG_SMP configurations on Armada XP, Armada 375 and Armada 38x
(which are multiple cores processors), but will no longer be used on
Armada 370 (which is a single core processor).
In the process, it simplifies the implementation of the
coherency_type() function, and adds a missing call to of_node_put().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Fixes: e60304f8cb7bb545e79fe62d9b9762460c254ec2 ("arm: mvebu: Add hardware I/O Coherency support") Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Link: https://lkml.kernel.org/r/1415871540-20302-3-git-send-email-thomas.petazzoni@free-electrons.com Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ll_add_cpu_to_smp_group(), ll_enable_coherency() and
ll_disable_coherency() are used on Armada XP to control the coherency
fabric. However, they make the assumption that the coherency fabric is
always available, which is currently a correct assumption but will no
longer be true with a followup commit that disables the usage of the
coherency fabric when the conditions are not met to use it.
Therefore, this commit modifies those functions so that they check the
return value of ll_get_coherency_base(), and if the return value is 0,
they simply return without configuring anything in the coherency
fabric.
The ll_get_coherency_base() function is also modified to properly
return 0 when the function is called with the MMU disabled. In this
case, it normally returns the physical address of the coherency
fabric, but we now check if the virtual address is 0, and if that's
case, return a physical address of 0 to indicate that the coherency
fabric is not enabled.
Commit d127e9c ("ARM: tegra: make tegra_resume can work with current and later
chips") removed tegra_get_soc_id macro leaving used cpu register corrupted after
branching to v7_invalidate_l1() and as result causing execution of unintended
code on tegra20. Possibly it was expected that r6 would be SoC id func argument
since common cpu reset handler is setting r6 before branching to tegra_resume(),
but neither tegra20_lp1_reset() nor tegra30_lp1_reset() aren't setting r6
register before jumping to resume function. Fix it by re-adding macro.
Fixes: d127e9c (ARM: tegra: make tegra_resume can work with current and later chips) Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating a dumb buffer object using the DRM_IOCTL_MODE_CREATE_DUMB
IOCTL, only the width, height, bpp and flags parameters are inputs. The
caller is not guaranteed to zero out or set handle, pitch and size, so
the driver must not treat these values as possible inputs.
Fixes a bug where running the Weston compositor on Tegra DRM would cause
an attempt to allocate a 3 GiB framebuffer to be allocated.
Earlier implementation assumed last instruction is BPF_EXIT.
Since this is no longer a restriction in eBPF, we remove this
limitation.
Per Alexei Starovoitov [1]:
> classic BPF has a restriction that last insn is always BPF_RET.
> eBPF doesn't have BPF_RET instruction and this restriction.
> It has BPF_EXIT insn which can appear anywhere in the program
> one or more times and it doesn't have to be last insn.
Commit a469abd0f868 (ARM: elf: add new hwcap for identifying atomic
ldrd/strd instructions) introduces HWCAP_ELF for 32-bit ARM
applications. As LPAE is always present on arm64, report the
corresponding compat HWCAP to user space.
As long as struct thin_c is in the list, anyone can grab a reference of
it. Consequently, we must wait for the reference count to drop to zero
*after* we remove the structure from the list, not before.
Discard bios and thin device deletion have the potential to release data
blocks. If the thin-pool is in out-of-data-space mode, and blocks were
released, transition the thin-pool back to full write mode.
The correct time to do this is just after the thin-pool metadata commit.
It cannot be done before the commit because the space maps will not
allow immediate reuse of the data blocks in case there's a rollback
following power failure.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the pool was in PM_OUT_OF_SPACE mode its process_prepared_discard
function pointer was incorrectly being set to
process_prepared_discard_passdown rather than process_prepared_discard.
This incorrect function pointer meant the discard was being passed down,
but not effecting the mapping. As such any discard that was issued, in
an attempt to reclaim blocks, would not successfully free data space.
Reported-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We never bother caching a partial block that is at the back end of the
origin device. No cell ever gets locked, but the calling code was
assuming it was and trying to release it.
Now the code only releases if the cell has been set to a non NULL
value.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the incoming bio is a WRITE and completely covers a block then we
don't bother to do any copying for a promotion operation. Once this is
done the cache block and origin block will be different, so we need to
set it to 'dirty'.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dm-bufio sets out to use the bio built into a struct dm_buffer to
issue an IO, it needs to call bio_reset after it's done with the bio
so that we can free things attached to the bio such as the integrity
payload. Therefore, inject our own endio callback to take care of
the bio_reset after calling submit_io's end_io callback.
Test case:
1. modprobe scsi_debug delay=0 dif=1 dix=199 ato=1 dev_size_mb=300
2. Set up a dm-bufio client, e.g. dm-verity, on the scsi_debug device
3. Repeatedly read metadata and watch kmalloc-192 leak!
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes kmemcheck warning in switch_names. The function
switch_names swaps inline names of two dentries. It swaps full arrays
d_iname, no matter how many bytes are really used by the strings. Reading
data beyond string ends results in kmemcheck warning.
We fix the bug by marking both arrays as fully initialized.
f2fs_write_begin() doesn't initialize the 'dn' variable if the inode has
inline data. However it uses its contents to decide whether it should
just zero out the page or load data to it. Thus if we are unlucky we can
zero out page contents instead of loading inline data into a page.
CC: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If user specifies too low end sector for trimming, f2fs_trim_fs() will
use uninitialized value as a number of trimmed blocks and returns it to
userspace. Initialize number of trimmed blocks early to avoid the
problem.
Coverity-id: 1248809 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code reads the default voltage selector from its register. If the
bootloader disables the regulator, the default voltage selector will be
0 which results in faulty behaviour of this regulator driver.
This patch sets a default voltage selector for vddpu if it is not set in
the register.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f1d2736c8156 (mmc: dw_mmc: control card read threshold) added
dw_mci_ctrl_rd_thld() with an unconditional write to the CDTHRCTL
register at offset 0x100. However before version 240a, the FIFO region
started at 0x100, so the write messes with the FIFO and completely
breaks the driver.
If the version id < 240A, return early from dw_mci_ctl_rd_thld() so as
not to hit this problem.
Some boards with TC6393XB chip require full state restore during system
resume thanks to chip's VCC being cut off during suspend (Sharp SL-6000
tosa is one of them). Failing to do so would result in ohci Oops on
resume due to internal memory contentes being changed. Fail ohci suspend
on tc6393xb is full state restore is required.
Recommended workaround is to unbind tmio-ohci driver before suspend and
rebind it after resume.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e7cd1d1eb16f ("mfd: twl4030-power: Add generic reset
configuration") accidentally removed the compatible flag for
"ti,twl4030-power" that should be there as documented in the
binding.
If "ti,twl4030-power" only the poweroff configuration is done
by the driver.
Fixes: e7cd1d1eb16f ("mfd: twl4030-power: Add generic reset configuration") Reported-by: "Dr. H. Nikolaus Schaller" <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a bug fix for using physical arch timers when
the arch_timer_use_virtual boolean is false. It restores the
arch_counter_get_cntpct() function after removal in
0d651e4e "clocksource: arch_timer: use virtual counters"
We need this on certain ARMv7 systems which are architected like this:
* The firmware doesn't know and doesn't care about hypervisor mode and
we don't want to add the complexity of hypervisor there.
* The firmware isn't involved in SMP bringup or resume.
* The ARCH timer come up with an uninitialized offset between the
virtual and physical counters. Each core gets a different random
offset.
* The device boots in "Secure SVC" mode.
* Nothing has touched the reset value of CNTHCTL.PL1PCEN or
CNTHCTL.PL1PCTEN (both default to 1 at reset)
One example of such as system is RK3288 where it is much simpler to
use the physical counter since there's nobody managing the offset and
each time a core goes down and comes back up it will get reinitialized
to some other random value.
Fixes: 0d651e4e65e9 ("clocksource: arch_timer: use virtual counters") Signed-off-by: Sonny Rao <sonnyrao@chromium.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Disables the F00F bug workaround warning. There is no F00F bug
workaround any more because Linux's standard IDT handling already
works around the F00F bug, but the warning still exists. This
is only cosmetic, and, in any event, there is no such thing as
KVM on a CPU with the F00F bug.
- Disables 32-bit APM BIOS detection. On a KVM paravirt system,
there should be no APM BIOS anyway.
- Disables tboot. I think that the tboot code should check the
CPUID hypervisor bit directly if it matters.
- paravirt_enabled disables espfix32. espfix32 should *not* be
disabled under KVM paravirt.
The last point is the purpose of this patch. It fixes a leak of the
high 16 bits of the kernel stack address on 32-bit KVM paravirt
guests. Fixes CVE-2014-8134.
Suggested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Users have no business installing custom code segments into the
GDT, and segments that are not present but are otherwise valid
are a historical source of interesting attacks.
For completeness, block attempts to set the L bit. (Prior to
this patch, the L bit would have been silently dropped.)
This is an ABI break. I've checked glibc, musl, and Wine, and
none of them look like they'll have any trouble.
Note to stable maintainers: this is a hardening patch that fixes
no known bugs. Given the possibility of ABI issues, this
probably shouldn't be backported quickly.
Signed-off-by: Andy Lutomirski <luto@amacapital.net> Acked-by: H. Peter Anvin <hpa@zytor.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rock Ridge extensions define so called Continuation Entries (CE) which
define where is further space with Rock Ridge data. Corrupted isofs
image can contain arbitrarily long chain of these, including a one
containing loop and thus causing kernel to end in an infinite loop when
traversing these entries.
Limit the traversal to 32 entries which should be more than enough space
to store all the Rock Ridge data.
Reported-by: P J P <ppandit@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In snd_usbmidi_error_timer(), the driver tries to resubmit MIDI input
URBs to reactivate the MIDI stream, but this causes the error when
some of URBs are still pending like:
... by not hitting rename_retry for reasons other than rename having
happened. In other words, do _not_ restart when finding that
between unlocking the child and locking the parent the former got
into __dentry_kill(). Skip the killed siblings instead...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Proper operation with the rewritten PCI mini driver requires that a flag be set
when interrupts are enabled. This flag was missed. This patch is one of three needed to
fix the kernel regression reported at https://bugzilla.kernel.org/show_bug.cgi?id=88951.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: Catalin Iacob <iacobcatalin@gmail.com> Tested-by: Catalin Iacob <iacobcatalin@gmail.com> Cc: Catalin Iacob <iacobcatalin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the major update of the rtlwifi-family of drivers, one of the callback entries
was missed, which leads to memory corruption. Unfortunately, this corruption
never caused a kernel oops, but showed up in other parts of the system.
This patch is one of three needed to fix the kernel regression reported at
https://bugzilla.kernel.org/show_bug.cgi?id=88951.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: Catalin Iacob <iacobcatalin@gmail.com> Tested-by: Catalin Iacob <iacobcatalin@gmail.com> Cc: Catalin Iacob <iacobcatalin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the major update of the rtlwifi-family of drivers, there was an editing
mistake. Unfortunately, this particular error leads to memory corruption that
silently leads to failure of the system. This patch is one of three needed to
fix the kernel regression reported at https://bugzilla.kernel.org/show_bug.cgi?id=88951.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: Catalin Iacob <iacobcatalin@gmail.com> Tested-by: Catalin Iacob <iacobcatalin@gmail.com> Cc: Catalin Iacob <iacobcatalin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For netlink, we shouldn't be using arch_fast_hash() as a hashing
discipline, but rather jhash() instead.
Since netlink sockets can be opened by any user, a local attacker
would be able to easily create collisions with the DPDK-derived
arch_fast_hash(), which trades off performance for security by
using crc32 CPU instructions on x86_64.
While it might have a legimite use case in other places, it should
be avoided in netlink context, though. As rhashtable's API is very
flexible, we could later on still decide on other hashing disciplines,
if legitimate.
Reference: http://thread.gmane.org/gmane.linux.kernel/1844123 Fixes: e341694e3eb5 ("netlink: Convert netlink_lookup() to use RCU protected hash table") Cc: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Thomas Graf <tgraf@suug.ch> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code should be using the _bh variant of rcu_dereference.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 97a6d1bb2b658ac85ed88205ccd1ab809899884d (xen-netfront: Fix
handling packets on compound pages with skb_linearize) attempted to
fix a problem where an skb that would have required too many slots
would be dropped causing TCP connections to stall.
However, it filled in the first slot using the original buffer and not
the new one and would use the wrong offset and grant access to the
wrong page.
Netback would notice the malformed request and stop all traffic on the
VIF, reporting:
Reported-by: Anthony Wright <anthony@overnetdata.com> Tested-by: Anthony Wright <anthony@overnetdata.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I cooked commit c3658e8d0f1 ("tcp: fix possible NULL dereference in
tcp_vX_send_reset()") I missed other spots we could deref a NULL
skb_dst(skb)
Again, if a socket is provided, we do not need skb_dst() to get a
pointer to network namespace : sock_net(sk) is good enough.
Reported-by: Dann Frazier <dann.frazier@canonical.com> Bisected-by: Dann Frazier <dann.frazier@canonical.com> Tested-by: Dann Frazier <dann.frazier@canonical.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Fixes: ca777eff51f7 ("tcp: remove dst refcount false sharing for prequeue mode") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To accomodate for enough headroom for tunnels, use MAX_HEADER instead
of LL_MAX_HEADER. Robert reported that he has hit after roughly 40hrs
of trinity an skb_under_panic() via SCTP output path (see reference).
I couldn't reproduce it from here, but not using MAX_HEADER as elsewhere
in other protocols might be one possible cause for this.
In any case, it looks like accounting on chunks themself seems to look
good as the skb already passed the SCTP output path and did not hit
any skb_over_panic(). Given tunneling was enabled in his .config, the
headroom would have been expanded by MAX_HEADER in this case.
Reported-by: Robert Święcki <robert@swiecki.net>
Reference: https://lkml.org/lkml/2014/12/1/507 Fixes: 594ccc14dfe4d ("[SCTP] Replace incorrect use of dev_alloc_skb with alloc_skb in sctp_packet_transmit().") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mvneta_tx() dereferences skb to get skb->len too late,
as hardware might have completed the transmit and TX completion
could have freed the skb from another cpu.
Fixes: 71f6d1b31fb1 ("net: mvneta: replace Tx timer with a real interrupt") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mvneta driver sets the amount of Tx coalesce packets to 16 by
default. Normally that does not cause any trouble since the driver
uses a much larger Tx ring size (532 packets). But some sockets
might run with very small buffers, much smaller than the equivalent
of 16 packets. This is what ping is doing for example, by setting
SNDBUF to 324 bytes rounded up to 2kB by the kernel.
The problem is that there is no documented method to force a specific
packet to emit an interrupt (eg: the last of the ring) nor is it
possible to make the NIC emit an interrupt after a given delay.
In this case, it causes trouble, because when ping sends packets over
its raw socket, the few first packets leave the system, and the first
15 packets will be emitted without an IRQ being generated, so without
the skbs being freed. And since the socket's buffer is small, there's
no way to reach that amount of packets, and the ping ends up with
"send: no buffer available" after sending 6 packets. Running with 3
instances of ping in parallel is enough to hide the problem, because
with 6 packets per instance, that's 18 packets total, which is enough
to grant a Tx interrupt before all are sent.
The original driver in the LSP kernel worked around this design flaw
by using a software timer to clean up the Tx descriptors. This timer
was slow and caused terrible network performance on some Tx-bound
workloads (such as routing) but was enough to make tools like ping
work correctly.
Instead here, we simply set the packet counts before interrupt to 1.
This ensures that each packet sent will produce an interrupt. NAPI
takes care of coalescing interrupts since the interrupt is disabled
once generated.
No measurable performance impact nor CPU usage were observed on small
nor large packets, including when saturating the link on Tx, and this
fixes tools like ping which rely on too small a send buffer. If one
wants to increase this value for certain workloads where it is safe
to do so, "ethtool -C $dev tx-frames" will override this default
setting.
This fix needs to be applied to stable kernels starting with 3.10.
Tested-By: Maggie Mae Roxas <maggie.mae.roxas@gmail.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove optimize_div() from BPF_MOD | BPF_K case
since we don't know the dividend and fix the
emit_mod() by reading the mod operation result from HI register
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org> Reviewed-by: Markos Chandras <markos.chandras@imgtec.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the inner mac header to point to the GRE payload when
doing GRO. This is needed if we proceed to send the packet
through GRE GSO which now uses the inner mac header instead
of inner network header to determine the length of encapsulation
headers.
Fixes: 14051f0452a2 ("gre: Use inner mac length when computing tunnel length") Reported-by: Wolfgang Walter <linux@stwm.de> Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, when trying to reuse a socket, vxlan_sock_add will grab
vn->sock_lock, locate a reusable socket, inc refcount and release
vn->sock_lock.
But vxlan_sock_release() will first decrement refcount, and then grab
that lock. refcnt operations are atomic but as currently we have
deferred works which hold vs->refcnt each, this might happen, leading to
a use after free (specially after vxlan_igmp_leave):
CPU 1 CPU 2
deferred work vxlan_sock_add
... ...
spin_lock(&vn->sock_lock)
vs = vxlan_find_sock();
vxlan_sock_release
dec vs->refcnt, reaches 0
spin_lock(&vn->sock_lock)
vxlan_sock_hold(vs), refcnt=1
spin_unlock(&vn->sock_lock)
hlist_del_rcu(&vs->hlist);
vxlan_notify_del_rx_port(vs)
spin_unlock(&vn->sock_lock)
So when we look for a reusable socket, we check if it wasn't freed
already before reusing it.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Fixes: 7c47cedf43a8b3 ("vxlan: move IGMP join/leave to work queue") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 7 Dec 2014 20:00:14 +0000 (12:00 -0800)]
Merge branch 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Three libata fixes for v3.18. Nothing too interesting. PCI ID ID and
quirk additions to ahci and an error handling path fix in sata_fsl"
* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: disable MSI on SAMSUNG 0xa800 SSD
sata_fsl: fix error handling of irq_of_parse_and_map
AHCI: Add DeviceIDs for Sunrise Point-LP SATA controller
Linus Torvalds [Sat, 6 Dec 2014 19:26:01 +0000 (11:26 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are two more driver bugfixes for I2C which would be good to have"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: cadence: Set the hardware time-out register to maximum value
i2c: davinci: generate STP always when NACK is received
Linus Torvalds [Fri, 5 Dec 2014 18:47:19 +0000 (10:47 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Two final fixlets for 3.18:
- Prevent microcode reload wreckage on 32bit
- Unbreak cross compilation"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode: Limit the microcode reloading to 64-bit for now
x86: Use $(OBJDUMP) instead of plain objdump
Linus Torvalds [Fri, 5 Dec 2014 06:39:37 +0000 (22:39 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm intel fixes from Dave Airlie:
"Two intel stable fixes, that should be it from me for this round"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Unlock panel even when LVDS is disabled
drm/i915: More cautious with pch fifo underruns
Linus Torvalds [Fri, 5 Dec 2014 01:48:13 +0000 (17:48 -0800)]
Merge tag 'pm+acpi-3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI backlight fix from Rafael Wysocki:
"This is a simple fix for an ACPI backlight regression introduced by a
recent commit that overlooked a corner case which should have been
taken into account"
* tag 'pm+acpi-3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: update condition to check if device is in _DOD list
Dave Airlie [Fri, 5 Dec 2014 01:12:29 +0000 (11:12 +1000)]
Merge tag 'drm-intel-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Silence some pch fifo underrun reports and panel locking backtraces,
both cc: stable.
* tag 'drm-intel-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Unlock panel even when LVDS is disabled
drm/i915: More cautious with pch fifo underruns
Linus Torvalds [Fri, 5 Dec 2014 00:06:02 +0000 (16:06 -0800)]
Merge tag 'media/v3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A core fix and some driver fixes:
- regression fix in Remote Controller core affecting RC6 protocol
handling
- fix video buffer handling in cx23885
- race fix in solo6x10
- fix image selection in smiapp
- fix reported payload size on s2255drv
- two updates for MAINTAINERS file"
* tag 'media/v3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] rc-core: fix toggle handling in the rc6 decoder
MAINTAINERS: Update mchehab's addresses
[media] cx23885: use sg = sg_next(sg) instead of sg++
[media] s2255drv: fix payload size for JPG, MJPEG
[media] Update MAINTAINERS for solo6x10
[media] solo6x10: fix a race in IRQ handler
[media] smiapp: Only some selection targets are settable
Masahiro Yamada [Thu, 4 Dec 2014 22:42:25 +0000 (14:42 -0800)]
uapi: fix to export linux/vm_sockets.h
A typo "header=y" was introduced by commit 7071cf7fc435 ("uapi: add
missing network related headers to kbuild").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vishnu Motghare [Wed, 3 Dec 2014 12:35:25 +0000 (18:05 +0530)]
i2c: cadence: Set the hardware time-out register to maximum value
Cadence I2C controller has bug wherein it generates invalid read transactions
after timeout in master receiver mode. This driver does not use the HW
timeout and this interrupt is disabled but the feature itself cannot be
disabled. Hence, this patch writes the maximum value (0xFF) to this register.
This is one of the workarounds to this bug and it will not avoid the issue
completely but reduces the chances of error.
i2c: davinci: generate STP always when NACK is received
According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]
Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).
For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:
S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->
The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.
Hence, fix it by generating Stop condition (STP) always when NACK is received.
This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a26eb ("i2c: omap: query STP always when NACK is received").
Tejun Heo [Thu, 4 Dec 2014 18:13:28 +0000 (13:13 -0500)]
ahci: disable MSI on SAMSUNG 0xa800 SSD
Just like 0x1600 which got blacklisted by 66a7cbc303f4 ("ahci: disable
MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes
on NCQ commands if MSI is enabled. Disable MSI.
Andy Lutomirski [Wed, 3 Dec 2014 23:37:08 +0000 (15:37 -0800)]
context_tracking: Restore previous state in schedule_user
It appears that some SCHEDULE_USER (asm for schedule_user) callers
in arch/x86/kernel/entry_64.S are called from RCU kernel context,
and schedule_user will return in RCU user context. This causes RCU
warnings and possible failures.
This is intended to be a minimal fix suitable for 3.18.
Reported-and-tested-by: Dave Jones <davej@redhat.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Frédéric Weisbecker <fweisbec@gmail.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 3 Dec 2014 22:08:50 +0000 (14:08 -0800)]
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree bugfix from Grant Likely:
"One more bug fix for v3.18. I debated whether or not to send you this
merge request because we're at such a late rc. The bug isn't critical
in that there is only one system known to be affected and the patch is
easy to backport. The codepath is used by pretty much every DT based
system, so there is risk a of regression (it /should/ be safe, but
I've been bitten by stuff that should be safe before). I've had it in
linux-next for a week and haven't received any complaints.
I think it probably should just be merged right away rather than
waiting for the merge window and backporting. It does fix a real bug
and the code is theoretically safer after the change. I can't think
of any situation where it would be dangerous to reserve the DT memory
an extra time.
Summary from tag:
Single bugfix for boot failure seen in the wild. The memory reserve
code tries to be clever about reserving the FDT, but it should just
go ahead and reserve it unconditionally to avoid the problem of
partial overlap described in the patch"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/fdt: memblock_reserve /memreserve/ regions in the case of partial overlap
Linus Torvalds [Wed, 3 Dec 2014 22:05:24 +0000 (14:05 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block core regression fix from Jens Axboe:
"Single fix for a regression introduced in this development cycle,
where dm on top of dif/dix is broken. From Darrick Wong"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix regression where bio_integrity_process uses wrong bio_vec iterator
Linus Torvalds [Wed, 3 Dec 2014 21:51:50 +0000 (13:51 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon and Nouveau fixes:
So nouveau had a few regression introduced, Ben and Maarten finally
tracked down the one that was causing problems on my MacBookPro, also
nvidia gave some info on the an engine we were using incorrectly, so
disable our use of it, and one regresion with pci hotplug affecting
optimus users.
Radeon has an oops fixs, sync fix, and one workaround to avoid broken
functionality on 32-bit x86, this needs better root causing and a
better fix, but the bandaid is a lot safer at this point"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
drm/radeon: Ignore RADEON_GEM_GTT_WC on 32-bit x86
drm/radeon: sync all BOs involved in a CS v2
nouveau: move the hotplug ignore to correct place.
drm/nouveau/gf116: remove copy1 engine
drm/nouveau: prevent stale fence->channel pointers, and protect with rcu
drm/nouveau/fifo/g84-: ack non-stall interrupt before handling it
1) Fill in ethtool link parameters for all link types in cxgb4, from
Hariprasad Shenai.
2) Fix probe regressions in stmmac driver, from Huacai Chen.
3) Network namespace leaks on errirs in rtnetlink, from Nicolas
Dichtel.
4) Remove erroneous BUG check which can actually trigger legitimately,
in xen-netfront. From Seth Forshee.
5) Validate length of IFLA_BOND_ARP_IP_TARGET netlink attributes, from
Thomas Grag.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
cxgb4: Fill in supported link mode for SFP modules
xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
sh_eth: Fix sleeping function called from invalid context
stmmac: platform: Move plat_dat checking earlier
sh_eth: Fix skb alloc size and alignment adjust rule.
rtnetlink: release net refcnt on error in do_setlink()
bond: Check length of IFLA_BOND_ARP_IP_TARGET attributes
Linus Torvalds [Wed, 3 Dec 2014 18:56:12 +0000 (10:56 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull keyring/nfs fixes from James Morris:
"From David Howells:
The first one fixes the handling of maximum buffer size for key
descriptions, fixing the size at 4095 + NUL char rather than whatever
PAGE_SIZE happens to be and permits you to read back the full
description without it getting clipped because some extra information
got prepended.
The second and third fix a bug in NFS idmapper handling whereby a key
representing a mapping between an id and a name expires and causing
EKEYEXPIRED to be seen internally in NFS (which prevents the mapping
from happening) rather than re-looking up the mapping"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: request_key() should reget expired keys rather than give EKEYEXPIRED
KEYS: Simplify KEYRING_SEARCH_{NO,DO}_STATE_CHECK flags
KEYS: Fix the size of the key description passed to/from userspace
Linus Torvalds [Wed, 3 Dec 2014 17:36:20 +0000 (09:36 -0800)]
Merge branch 'akpm' (patches from Andrew Morton)
Merge misc fixes from Andrew Morton:
"10 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
slab: fix nodeid bounds check for non-contiguous node IDs
lib/genalloc.c: export devm_gen_pool_create() for modules
mm: fix anon_vma_clone() error treatment
mm: fix swapoff hang after page migration and fork
fat: fix oops on corrupted vfat fs
ipc/sem.c: fully initialize sem_array before making it visible
drivers/input/evdev.c: don't kfree() a vmalloc address
mm/vmpressure.c: fix race in vmpressure_work_fn()
mm: frontswap: invalidate expired data on a dup-store failure
mm: do not overwrite reserved pages counter at show_mem()
Paul Mackerras [Tue, 2 Dec 2014 23:59:48 +0000 (15:59 -0800)]
slab: fix nodeid bounds check for non-contiguous node IDs
The bounds check for nodeid in ____cache_alloc_node gives false
positives on machines where the node IDs are not contiguous, leading to
a panic at boot time. For example, on a POWER8 machine the node IDs are
typically 0, 1, 16 and 17. This means that num_online_nodes() returns
4, so when ____cache_alloc_node is called with nodeid = 16 the VM_BUG_ON
triggers, like this:
To fix this, we instead compare the nodeid with MAX_NUMNODES, and
additionally make sure it isn't negative (since nodeid is an int). The
check is there mainly to protect the array dereference in the get_node()
call in the next line, and the array being dereferenced is of size
MAX_NUMNODES. If the nodeid is in range but invalid (for example if the
node is off-line), the BUG_ON in the next line will catch that.
Fixes: 14e50c6a9bc2 ("mm: slab: Verify the nodeid passed to ____cache_alloc_node") Signed-off-by: Paul Mackerras <paulus@samba.org> Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Reviewed-by: Pekka Enberg <penberg@kernel.org> Acked-by: David Rientjes <rientjes@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Forrest [Tue, 2 Dec 2014 23:59:42 +0000 (15:59 -0800)]
mm: fix anon_vma_clone() error treatment
Andrew Morton noticed that the error return from anon_vma_clone() was
being dropped and replaced with -ENOMEM (which is not itself a bug
because the only error return value from anon_vma_clone() is -ENOMEM).
I did an audit of callers of anon_vma_clone() and discovered an actual
bug where the error return was being lost. In __split_vma(), between
Linux 3.11 and 3.12 the code was changed so the err variable is used
before the call to anon_vma_clone() and the default initial value of
-ENOMEM is overwritten. So a failure of anon_vma_clone() will return
success since err at this point is now zero.
Below is a patch which fixes this bug and also propagates the error
return value from anon_vma_clone() in all cases.
Fixes: ef0855d334e1 ("mm: mempolicy: turn vma_set_policy() into vma_dup_policy()") Signed-off-by: Daniel Forrest <dan.forrest@ssec.wisc.edu> Reviewed-by: Michal Hocko <mhocko@suse.cz> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Tim Hartrick <tim@edgecast.com> Cc: Hugh Dickins <hughd@google.com> Cc: Michel Lespinasse <walken@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> [3.12+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Tue, 2 Dec 2014 23:59:39 +0000 (15:59 -0800)]
mm: fix swapoff hang after page migration and fork
I've been seeing swapoff hangs in recent testing: it's cycling around
trying unsuccessfully to find an mm for some remaining pages of swap.
I have been exercising swap and page migration more heavily recently,
and now notice a long-standing error in copy_one_pte(): it's trying to
add dst_mm to swapoff's mmlist when it finds a swap entry, but is doing
so even when it's a migration entry or an hwpoison entry.
Which wouldn't matter much, except it adds dst_mm next to src_mm,
assuming src_mm is already on the mmlist: which may not be so. Then if
pages are later swapped out from dst_mm, swapoff won't be able to find
where to replace them.
There's already a !non_swap_entry() test for stats: move that up before
the swap_duplicate() and the addition to mmlist.
Manfred Spraul [Tue, 2 Dec 2014 23:59:34 +0000 (15:59 -0800)]
ipc/sem.c: fully initialize sem_array before making it visible
ipc_addid() makes a new ipc identifier visible to everyone. New objects
start as locked, so that the caller can complete the initialization
after the call. Within struct sem_array, at least sma->sem_base and
sma->sem_nsems are accessed without any locks, therefore this approach
doesn't work.
Thus: Move the ipc_addid() to the end of the initialization.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com> Reported-by: Rik van Riel <riel@redhat.com> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Davidlohr Bueso <dave@stgolabs.net> Acked-by: Rafael Aquini <aquini@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Seth Forshee [Wed, 26 Nov 2014 02:28:24 +0000 (20:28 -0600)]
xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
These BUGs can be erroneously triggered by frags which refer to
tail pages within a compound page. The data in these pages may
overrun the hardware page while still being contained within the
compound page, but since compound_order() evaluates to 0 for tail
pages the assertion fails. The code already iterates through
subsequent pages correctly in this scenario, so the BUGs are
unnecessary and can be removed.
Fixes: f36c374782e4 ("xen/netfront: handle compound page fragments on transmit") Cc: <stable@vger.kernel.org> # 3.7+ Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Weijie Yang [Tue, 2 Dec 2014 23:59:25 +0000 (15:59 -0800)]
mm: frontswap: invalidate expired data on a dup-store failure
If a frontswap dup-store failed, it should invalidate the expired page
in the backend, or it could trigger some data corruption issue.
Such as:
1. use zswap as the frontswap backend with writeback feature
2. store a swap page(version_1) to entry A, success
3. dup-store a newer page(version_2) to the same entry A, fail
4. use __swap_writepage() write version_2 page to swapfile, success
5. zswap do shrink, writeback version_1 page to swapfile
6. version_2 page is overwrited by version_1, data corrupt.
This patch fixes this issue by invalidating expired data immediately
when meet a dup-store failure.
Signed-off-by: Weijie Yang <weijie.yang@samsung.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Seth Jennings <sjennings@variantweb.net> Cc: Dan Streetman <ddstreet@ieee.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Bob Liu <bob.liu@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Airlie [Wed, 3 Dec 2014 00:48:54 +0000 (10:48 +1000)]
Merge branch 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
A few more small fixes for 3.18.
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
drm/radeon: Ignore RADEON_GEM_GTT_WC on 32-bit x86
drm/radeon: sync all BOs involved in a CS v2
projects / linux / log