Since commit a36e185e8c85
("udp: Handle ICMP errors for tunnels with same destination port on both endpoints")
UDP's handling of ICMP errors has allowed for UDP-encap tunnels to
determine socket associations in scenarios where the UDP hash lookup
could not.
Subsequently, commit d26796ae58940
("udp: check udp sock encap_type in __udp_lib_err")
subtly tweaked the approach such that UDP ICMP error handling would be
skipped for any UDP socket which has encapsulation enabled.
In the case of L2TP tunnel sockets using UDP-encap, this latter
modification effectively broke ICMP error reporting for the L2TP
control plane.
To a degree this isn't catastrophic inasmuch as the L2TP control
protocol defines a reliable transport on top of the underlying packet
switching network which will eventually detect errors and time out.
However, paying attention to the ICMP error reporting allows for more
timely detection of errors in L2TP userspace, and aids in debugging
connectivity issues.
Reinstate ICMP error handling for UDP encap L2TP tunnels:
* implement struct udp_tunnel_sock_cfg .encap_err_rcv in order to allow
the L2TP code to handle ICMP errors;
* only implement error-handling for tunnels which have a managed
socket: unmanaged tunnels using a kernel socket have no userspace to
report errors back to;
* flag the error on the socket, which allows for userspace to get an
error such as -ECONNREFUSED back from sendmsg/recvmsg;
* pass the error into ip[v6]_icmp_error() which allows for userspace to
get extended error information via. MSG_ERRQUEUE.
Fixes: d26796ae5894 ("udp: check udp sock encap_type in __udp_lib_err") Signed-off-by: Tom Parkin <tparkin@katalix.com> Link: https://lore.kernel.org/r/20240513172248.623261-1-tparkin@katalix.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When VLAN tag strip is changed to enable or disable, the hardware requires
the Rx ring to be in a disabled state, otherwise the feature cannot be
changed.
Fixes: f3b03c655f67 ("net: wangxun: Implement vlan add and kill functions") Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the current interrupt controller, the MAC interrupt acts as the
parent interrupt in the GPIO IRQ chip. But when the number of Rx/Tx
ring changes, the PCI IRQ vector needs to be reallocated. Then this
interrupt controller would be corrupted. So use irq_domain structure
to avoid the above problem.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 1d3c6414950b ("net: txgbe: fix to control VLAN strip") Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to change the interrupt response structure, there will be a
lot of code added next. Move these interrupt codes to a new file, to
make the codes cleaner.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 1d3c6414950b ("net: txgbe: fix to control VLAN strip") Signed-off-by: Sasha Levin <sashal@kernel.org>
Hardware requires VLAN CTAG and STAG configuration always matches. And
whether VLAN CTAG or STAG changes, the configuration needs to be changed
as well.
Fixes: 6670f1ece2c8 ("net: txgbe: Add netdev features support") Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com> Reviewed-by: Sai Krishna <saikrishnag@marvell.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the issue where some Rx features cannot be changed.
When using ethtool -K to turn off rx offload, it returns error and
displays "Could not change any device features". And netdev->features
is not assigned a new value to actually configure the hardware.
Fixes: 6dbedcffcf54 ("net: libwx: Implement xx_set_features ops") Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
... we find that the cpu.max.burst value changed unexpectedly.
In cpu_max_write(), the unit of the burst value returned
by tg_get_cfs_burst() is microseconds, while in cpu_max_write(),
the burst unit used for calculation should be nanoseconds,
which leads to the bug.
To fix it, get the burst value directly from tg->cfs_bandwidth.burst.
trafgen performance considerably sank on hosts with many cores
after the blamed commit.
packet_read_pending() is very expensive, and calling it
in af_packet fast path defeats Daniel intent in commit b013840810c2 ("packet: use percpu mmap tx frame pending refcount")
tpacket_destruct_skb() makes room for one packet, we can immediately
wakeup a producer, no need to completely drain the tx ring.
Fixes: 89ed5b519004 ("af_packet: Block execution of tasks waiting for transmit to complete in AF_PACKET") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neil Horman <nhorman@tuxdriver.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20240515163358.4105915-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Disabling tcp-data-split on idpf silently fails:
# ethtool -G $NETDEV tcp-data-split off
# ethtool -g $NETDEV | grep 'TCP data split'
TCP data split: on
But it works if you also change 'tx' or 'rx':
# ethtool -G $NETDEV tcp-data-split off tx 256
# ethtool -g $NETDEV | grep 'TCP data split'
TCP data split: off
The bug is in idpf_set_ringparam, where it takes a shortcut out if the
TX and RX sizes are not changing. Fix it by checking also if the
tcp-data-split setting remains unchanged. Only then can the soft reset
be skipped.
Fixes: 9b1aa3ef2328 ("idpf: add get/set for Ethtool's header split ringparam") Reported-by: Xu Du <xudu@redhat.com> Closes: https://issues.redhat.com/browse/RHEL-36182 Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com> Link: https://lore.kernel.org/r/20240515092414.158079-1-mschmidt@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no need to add the name to ns_list again if the netns already
recoreded.
Fixes: 25ae948b4478 ("selftests/net: add lib.sh") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The qrtr protocol core logic and the qrtr nameservice are combined into
a single module. Neither the core logic or nameservice provide much
functionality by themselves; combining the two into a single module also
prevents any possible issues that may stem from client modules loading
inbetween qrtr and the ns.
Creating a socket takes two references to the module that owns the
socket protocol. Since the ns needs to create the control socket, this
creates a scenario where there are always two references to the qrtr
module. This prevents the execution of 'rmmod' for qrtr.
To resolve this, forcefully put the module refcount for the socket
opened by the nameservice.
Fixes: a365023a76f2 ("net: qrtr: combine nameservice into main module") Reported-by: Jeffrey Hugo <quic_jhugo@quicinc.com> Tested-by: Jeffrey Hugo <quic_jhugo@quicinc.com> Signed-off-by: Chris Lew <quic_clew@quicinc.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported a suspicious rcu usage[1] in bridge's mst code. While
fixing it I noticed that nothing prevents a vlan to be freed while
walking the list from the same path (br forward delay timer). Fix the rcu
usage and also make sure we are not accessing freed memory by making
br_mst_vlan_set_state use rcu read lock.
When running the bridge IGMP/MLD selftests on debug kernels we can get
spurious errors when setting up the IGMP/MLD exclude timeout tests
because the membership interval is just 3 seconds and the setup has 2
seconds of sleep plus various validations, the one second that is left
is not enough. Increase the membership interval from 3 to 5 seconds to
make room for the setup validation and 2 seconds of sleep.
Fixes: 34d7ecb3d4f7 ("selftests: net: bridge: update IGMP/MLD membership interval value") Reported-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot triggered an uninit value[1] error in bridge device's xmit path
by sending a short (less than ETH_HLEN bytes) skb. To fix it check if
we can actually pull that amount instead of assuming.
Tested with dropwatch:
drop at: br_dev_xmit+0xb93/0x12d0 [bridge] (0xffffffffc06739b3)
origin: software
timestamp: Mon May 13 11:31:53 2024 778214037 nsec
protocol: 0x88a8
length: 2
original length: 2
drop reason: PKT_TOO_SMALL
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot+a63a1f6a062033cf0f40@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=a63a1f6a062033cf0f40 Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the ABI was updated to prevent same name w/different args, it
missed an important corner case when fields don't end with a space.
Typically, space is used for fields to help separate them, like
"u8 field1; u8 field2". If no spaces are used, like
"u8 field1;u8 field2", then the parsing works for the first time.
However, the match check fails on a subsequent register, leading to
confusion.
This is because the match check uses argv_split() and assumes that all
fields will be split upon the space. When spaces are used, we get back
{ "u8", "field1;" }, without spaces we get back { "u8", "field1;u8" }.
This causes a mismatch, and the user program gets back -EADDRINUSE.
Add a method to detect this case before calling argv_split(). If found
force a space after the field separator character ';'. This ensures all
cases work properly for matching.
With this fix, the following are all treated as matching:
u8 field1;u8 field2
u8 field1; u8 field2
u8 field1;\tu8 field2
u8 field1;\nu8 field2
The current code for finding and deleting events assumes that there will
never be cases when user_events are registered with the same name, but
different formats. Scenarios exist where programs want to use the same
name but have different formats. An example is multiple versions of a
program running side-by-side using the same event name, but with updated
formats in each version.
This change does not yet allow for multi-format events. If user_events
are registered with the same name but different arguments the programs
see the same return values as before. This change simply makes it
possible to easily accommodate for this.
Update find_user_event() to take in argument parameters and register
flags to accommodate future multi-format event scenarios. Have find
validate argument matching and return error pointers to cover when
an existing event has the same name but different format. Update
callers to handle error pointer logic.
Move delete_user_event() to use hash walking directly now that
find_user_event() has changed. Delete all events found that match the
register name, stop if an error occurs and report back to the user.
Update user_fields_match() to cover list_empty() scenarios now that
find_user_event() uses it directly. This makes the logic consistent
across several callsites.
Truncate the device name to store IPoIB VLAN name.
[leonro@5b4e8fba4ddd kernel]$ make -s -j 20 allmodconfig
[leonro@5b4e8fba4ddd kernel]$ make -s -j 20 W=1 drivers/infiniband/ulp/ipoib/
drivers/infiniband/ulp/ipoib/ipoib_vlan.c: In function ‘ipoib_vlan_add’:
drivers/infiniband/ulp/ipoib/ipoib_vlan.c:187:52: error: ‘%04x’
directive output may be truncated writing 4 bytes into a region of size
between 0 and 15 [-Werror=format-truncation=]
187 | snprintf(intf_name, sizeof(intf_name), "%s.%04x",
| ^~~~
drivers/infiniband/ulp/ipoib/ipoib_vlan.c:187:48: note: directive
argument in the range [0, 65535]
187 | snprintf(intf_name, sizeof(intf_name), "%s.%04x",
| ^~~~~~~~~
drivers/infiniband/ulp/ipoib/ipoib_vlan.c:187:9: note: ‘snprintf’ output
between 6 and 21 bytes into a destination of size 16
187 | snprintf(intf_name, sizeof(intf_name), "%s.%04x",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
188 | ppriv->dev->name, pkey);
| ~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[6]: *** [scripts/Makefile.build:244: drivers/infiniband/ulp/ipoib/ipoib_vlan.o] Error 1
make[6]: *** Waiting for unfinished jobs....
Dan Carpenter says:
> Commit 5866efa8cbfb ("SUNRPC: Fix svcauth_gss_proxy_init()") from Oct
> 24, 2019 (linux-next), leads to the following Smatch static checker
> warning:
>
> net/sunrpc/auth_gss/svcauth_gss.c:1039 gss_free_in_token_pages()
> warn: iterator 'i' not incremented
>
> net/sunrpc/auth_gss/svcauth_gss.c
> 1034 static void gss_free_in_token_pages(struct gssp_in_token *in_token)
> 1035 {
> 1036 u32 inlen;
> 1037 int i;
> 1038
> --> 1039 i = 0;
> 1040 inlen = in_token->page_len;
> 1041 while (inlen) {
> 1042 if (in_token->pages[i])
> 1043 put_page(in_token->pages[i]);
> ^
> This puts page zero over and over.
>
> 1044 inlen -= inlen > PAGE_SIZE ? PAGE_SIZE : inlen;
> 1045 }
> 1046
> 1047 kfree(in_token->pages);
> 1048 in_token->pages = NULL;
> 1049 }
Based on the way that the ->pages[] array is constructed in
gss_read_proxy_verf(), we know that once the loop encounters a NULL
page pointer, the remaining array elements must also be NULL.
Undefined behavior is triggered when bnxt_qplib_alloc_init_hwq is called
with hwq_attr->aux_depth != 0 and hwq_attr->aux_stride == 0.
In that case, "roundup_pow_of_two(hwq_attr->aux_stride)" gets called.
roundup_pow_of_two is documented as undefined for 0.
Fix it in the one caller that had this combination.
In of_modalias(), if the buffer happens to be too small even for the 1st
snprintf() call, the len parameter will become negative and str parameter
(if not NULL initially) will point beyond the buffer's end. Add the buffer
overflow check after the 1st snprintf() call and fix such check after the
strlen() call (accounting for the terminating NUL char).
Fixes: bc575064d688 ("of/device: use of_property_for_each_string to parse compatible strings") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Link: https://lore.kernel.org/r/bbfc6be0-c687-62b6-d015-5141b93f313e@omp.ru Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to ipq5018.dtsi, the maximum supported rate by the
CPU is 1.008 GHz on the IPQ5018 platform, however the current
configuration of the PLL results in 1.2 GHz rate.
Change the 'L' value in the PLL configuration to limit the
rate to 1.008 GHz. The downstream kernel also uses the same
value [1]. Also add a comment to indicate the desired
frequency.
__filemap_get_folio() with FGP_WRITEBEGIN parameter has already wait
for stable folio, so remove the redundant folio_wait_stable() in
ext4_da_write_begin(), it was left over from the commit cc883236b792
("ext4: drop unnecessary journal handle in delalloc write") that
removed the retry getting page logic.
Fixes: cc883236b792 ("ext4: drop unnecessary journal handle in delalloc write") Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20240419023005.2719050-1-yi.zhang@huaweicloud.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_NFSD_LEGACY_CLIENT_TRACKING is not set, the virtual file
/proc/fs/nfsd/nfsv4recoverydir
is created but responds EINVAL to any access.
This is not useful, is somewhat surprising, and it causes ltp to
complain.
The only known user of this file is in nfs-utils, which handles
non-existence and read-failure equally well. So there is nothing to
gain from leaving the file present but inaccessible.
So this patch removes the file when its content is not available - i.e.
when that config option is not selected.
Also remove the #ifdef which hides some of the enum values when
CONFIG_NFSD_V$ not selection. simple_fill_super() quietly ignores array
entries that are not present, so having slots in the array that don't
get used is perfectly acceptable. So there is no value in this #ifdef.
Reported-by: Petr Vorel <pvorel@suse.cz> Reviewed-by: Jeff Layton <jlayton@kernel.org> Fixes: 74fd48739d04 ("nfsd: new Kconfig option for legacy client tracking") Signed-off-by: NeilBrown <neilb@suse.de> Reviewed-by: Petr Vorel <pvorel@suse.cz> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
since vs_proc pointer is dereferenced before getting it's address there's
no need to check for NULL.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 8e5b67731d08 ("SUNRPC: Add a callback to initialise server requests") Signed-off-by: Aleksandr Aprelkov <aaprelkov@usergate.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch series "mm: follow_pte() improvements and acrn follow_pte() fixes".
Patch #1 fixes a bunch of issues I spotted in the acrn driver. It
compiles, that's all I know. I'll appreciate some review and testing from
acrn folks.
Patch #2+#3 improve follow_pte(), passing a VMA instead of the MM, adding
more sanity checks, and improving the documentation. Gave it a quick test
on x86-64 using VM_PAT that ends up using follow_pte().
This patch (of 3):
We currently miss handling various cases, resulting in a dangerous
follow_pte() (previously follow_pfn()) usage.
(1) We're not checking PTE write permissions.
Maybe we should simply always require pte_write() like we do for
pin_user_pages_fast(FOLL_WRITE)? Hard to tell, so let's check for
ACRN_MEM_ACCESS_WRITE for now.
(2) We're not rejecting refcounted pages.
As we are not using MMU notifiers, messing with refcounted pages is
dangerous and can result in use-after-free. Let's make sure to reject them.
(3) We are only looking at the first PTE of a bigger range.
We only lookup a single PTE, but memmap->len may span a larger area.
Let's loop over all involved PTEs and make sure the PFN range is
actually contiguous. Reject everything else: it couldn't have worked
either way, and rather made use access PFNs we shouldn't be accessing.
Link: https://lkml.kernel.org/r/20240410155527.474777-1-david@redhat.com Link: https://lkml.kernel.org/r/20240410155527.474777-2-david@redhat.com Fixes: 8a6e85f75a83 ("virt: acrn: obtain pa from VMA with PFNMAP flag") Signed-off-by: David Hildenbrand <david@redhat.com> Cc: Alex Williamson <alex.williamson@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Fei Li <fei1.li@intel.com> Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Yonghua Huang <yonghua.huang@intel.com> Cc: Sean Christopherson <seanjc@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This series open codes follow_pfn in the only remaining caller, although
the code there remains questionable. It then also moves follow_phys into
the only user and simplifies it a bit.
This patch (of 3):
Switch from follow_pfn to follow_pte so that we can get rid of follow_pfn.
Note that this doesn't fix any of the pre-existing raciness and lack of
permission checking in the code.
Link: https://lkml.kernel.org/r/20240324234542.2038726-1-hch@lst.de Link: https://lkml.kernel.org/r/20240324234542.2038726-2-hch@lst.de Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Fei Li <fei1.li@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: 3d6586008f7b ("drivers/virt/acrn: fix PFNMAP PTE checks in acrn_vm_ram_map()") Signed-off-by: Sasha Levin <sashal@kernel.org>
Intoduce helpers to work with mana ib queues (struct mana_ib_queue).
A queue always consists of umem, gdma_region, and id.
A queue can become a WQ or a CQ.
A user with minimum journal size (1024 blocks these days) complained
about the following error triggered by generic/697 test in
ext4_tmpfile():
run fstests generic/697 at 2024-02-28 05:34:46
JBD2: vfstest wants too many credits credits:260 rsv_credits:0 max:256
EXT4-fs error (device loop0) in __ext4_new_inode:1083: error 28
Indeed the credit estimate in ext4_tmpfile() is huge.
EXT4_MAXQUOTAS_INIT_BLOCKS() is 219, then 10 credits from ext4_tmpfile()
itself and then ext4_xattr_credits_for_new_inode() adds more credits
needed for security attributes and ACLs. Now the
EXT4_MAXQUOTAS_INIT_BLOCKS() is in fact unnecessary because we've
already initialized quotas with dquot_init() shortly before and so
EXT4_MAXQUOTAS_TRANS_BLOCKS() is enough (which boils down to 3 credits).
Fixes: af51a2ac36d1 ("ext4: ->tmpfile() support") Signed-off-by: Jan Kara <jack@suse.cz> Tested-by: Luis Henriques <lhenriques@suse.de> Tested-by: Disha Goel <disgoel@linux.ibm.com> Link: https://lore.kernel.org/r/20240307115320.28949-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
The x86 instruction decoder is used not only for decoding kernel
instructions. It is also used by perf uprobes (user space probes) and by
perf tools Intel Processor Trace decoding. Consequently, it needs to
support instructions executed by user space also.
Intel Architecture Instruction Set Extensions and Future Features manual
number 319433-044 of May 2021, documented VEX versions of instructions
VPDPBUSD, VPDPBUSDS, VPDPWSSD and VPDPWSSDS, but the opcode map has them
listed as EVEX only.
Remove EVEX-only (ev) annotation from instructions VPDPBUSD, VPDPBUSDS,
VPDPWSSD and VPDPWSSDS, which allows them to be decoded with either a VEX
or EVEX prefix.
Fixes: 0153d98f2dd6 ("x86/insn: Add misc instructions to x86 instruction decoder") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/20240502105853.5338-4-adrian.hunter@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The x86 instruction decoder is used not only for decoding kernel
instructions. It is also used by perf uprobes (user space probes) and by
perf tools Intel Processor Trace decoding. Consequently, it needs to
support instructions executed by user space also.
Opcode 0x68 PUSH instruction is currently defined as 64-bit operand size
only i.e. (d64). That was based on Intel SDM Opcode Map. However that is
contradicted by the Instruction Set Reference section for PUSH in the
same manual.
Remove 64-bit operand size only annotation from opcode 0x68 PUSH
instruction.
Example:
$ cat pushw.s
.global _start
.text
_start:
pushw $0x1234
mov $0x1,%eax # system call number (sys_exit)
int $0x80
$ as -o pushw.o pushw.s
$ ld -s -o pushw pushw.o
$ objdump -d pushw | tail -4 0000000000401000 <.text>:
401000: 66 68 34 12 pushw $0x1234
401004: b8 01 00 00 00 mov $0x1,%eax
401009: cd 80 int $0x80
$ perf record -e intel_pt//u ./pushw
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.014 MB perf.data ]
On SM8650 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display af54000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
Fixes: 9e939f008338 ("clk: qcom: add the SM8650 Display Clock Controller driver") Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-4-b44038f3fa96@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On SM8550 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display ae90000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
Fixes: 90114ca11476 ("clk: qcom: add SM8550 DISPCC driver") Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-3-b44038f3fa96@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On SM6350 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display ae90000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
On SM8450 DisplayPort link clocks use frequency tables inherited from
the vendor kernel, it is not applicable in the upstream kernel. Drop
frequency tables and use clk_byte2_ops for those clocks.
This fixes frequency selection in the OPP core (which otherwise attempts
to use invalid 810 KHz as DP link rate), also fixing the following
message:
msm-dp-display ae90000.displayport-controller: _opp_config_clk_single: failed to set clock rate: -22
Fixes: 16fb89f92ec4 ("clk: qcom: Add support for Display Clock Controller on SM8450") Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20240424-dispcc-dp-clocks-v2-1-b44038f3fa96@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch series "mm/ksm: fix ksm exec support for prctl", v4.
commit 3c6f33b7273a ("mm/ksm: support fork/exec for prctl") inherits
MMF_VM_MERGE_ANY flag when a task calls execve(). However, it doesn't
create the mm_slot, so ksmd will not try to scan this task. The first
patch fixes the issue.
The second patch refactors to prepare for the third patch. The third
patch extends the selftests of ksm to verfity the deduplication really
happens after fork/exec inherits ths KSM setting.
This patch (of 3):
commit 3c6f33b7273a ("mm/ksm: support fork/exec for prctl") inherits
MMF_VM_MERGE_ANY flag when a task calls execve(). Howerver, it doesn't
create the mm_slot, so ksmd will not try to scan this task.
To fix it, allocate and add the mm_slot to ksm_mm_head in __bprm_mm_init()
when the mm has MMF_VM_MERGE_ANY flag.
Link: https://lkml.kernel.org/r/20240328111010.1502191-1-tujinjiang@huawei.com Link: https://lkml.kernel.org/r/20240328111010.1502191-2-tujinjiang@huawei.com Fixes: 3c6f33b7273a ("mm/ksm: support fork/exec for prctl") Signed-off-by: Jinjiang Tu <tujinjiang@huawei.com> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Nanyong Sun <sunnanyong@huawei.com> Cc: Rik van Riel <riel@surriel.com> Cc: Stefan Roesch <shr@devkernel.io> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kcalloc() in dmirror_device_evict_chunk() will return null if the
physical memory has run out. As a result, if src_pfns or dst_pfns is
dereferenced, the null pointer dereference bug will happen.
Moreover, the device is going away. If the kcalloc() fails, the pages
mapping a chunk could not be evicted. So add a __GFP_NOFAIL flag in
kcalloc().
Finally, as there is no need to have physically contiguous memory, Switch
kcalloc() to kvcalloc() in order to avoid failing allocations.
According to Figure 52A.1 ("RS-CANFD Module Block Diagram (in classical
CAN mode)") in the R-Car V3U Series User’s Manual Rev. 0.5, the parent
clock for the CANFD peripheral module clock is the S3D2 clock.
mlx5 has a built in self-test at driver startup to evaluate if the
platform supports write combining to generate a 64 byte PCIe TLP or
not. This has proven necessary because a lot of common scenarios end up
with broken write combining (especially inside virtual machines) and there
is other way to learn this information.
This self test has been consistently failing on new ARM64 CPU
designs (specifically with NVIDIA Grace's implementation of Neoverse
V2). The C loop around writeq() generates some pretty terrible ARM64
assembly, but historically this has worked on a lot of existing ARM64 CPUs
till now.
We see it succeed about 1 time in 10,000 on the worst effected
systems. The CPU architects speculate that the load instructions
interspersed with the stores makes the WC buffers statistically flush too
often and thus the generation of large TLPs becomes infrequent. This makes
the boot up test unreliable in that it indicates no write-combining,
however userspace would be fine since it uses a ST4 instruction.
Further, S390 has similar issues where only the special zpci_memcpy_toio()
will actually generate large TLPs, and the open coded loop does not
trigger it at all.
Fix both ARM64 and S390 by switching to __iowrite64_copy() which now
provides architecture specific variants that have a high change of
generating a large TLP with write combining. x86 continues to use a
similar writeq loop in the generate __iowrite64_copy().
Fixes: 11f552e21755 ("IB/mlx5: Test write combining support") Link: https://lore.kernel.org/r/6-v3-1893cd8b9369+1925-mlx5_arm_wc_jgg@nvidia.com Tested-by: Niklas Schnelle <schnelle@linux.ibm.com> Acked-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In rxe_send() a ref is taken on the qp to keep it alive until the
kfree_skb() has a chance to call the skb destructor rxe_skb_tx_dtor()
which drops the reference. If the packet has an incorrect protocol the
error path just calls kfree_skb() which will call the destructor which
will drop the ref. Currently the driver also calls rxe_put() which is
incorrect. Additionally since the packets sent to rxe_send() are under the
control of the driver and it only ever produces IPV4 or IPV6 packets the
simplest fix is to remove all the code in this block.
Link: https://lore.kernel.org/r/20240329145513.35381-12-rpearsonhpe@gmail.com Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com> Fixes: 9eb7f8e44d13 ("IB/rxe: Move refcounting earlier in rxe_send()") Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A previous commit incorrectly added an 'if(!err)' before scheduling the
requester task in rxe_post_send_kernel(). But if there were send wrs
successfully added to the send queue before a bad wr they might never get
executed.
This commit fixes this by scheduling the requester task if any wqes were
successfully posted in rxe_post_send_kernel() in rxe_verbs.c.
In rxe_comp_queue_pkt() an incoming response packet skb is enqueued to the
resp_pkts queue and then a decision is made whether to run the completer
task inline or schedule it. Finally the skb is dereferenced to bump a 'hw'
performance counter. This is wrong because if the completer task is
already running in a separate thread it may have already processed the skb
and freed it which can cause a seg fault. This has been observed
infrequently in testing at high scale.
This patch fixes this by changing the order of enqueuing the packet until
after the counter is accessed.
The offset of the CONFIG_CTL_U register defined for the Stromer
PLL is wrong. It is not aligned on a 4 bytes boundary which might
causes errors in regmap operations.
Maybe the intention behind of using the 0xff value was to indicate
that the register is not implemented in the PLL, but this is not
verified anywhere in the code. Moreover, this value is not used
even in other register offset arrays despite that those PLLs also
have unimplemented registers.
Additionally, on the Stromer PLLs the current code only touches
the CONFIG_CTL_U register if the result of pll_has_64bit_config()
is true which condition is not affected by the change.
Due to the reasons above, simply remove the CONFIG_CTL_U entry
from the Stromer specific array.
Fixes: e47a4f55f240 ("clk: qcom: clk-alpha-pll: Add support for Stromer PLLs") Signed-off-by: Gabor Juhos <j4g8y7@gmail.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20240311-alpha-pll-stromer-cleanup-v1-1-f7c0c5607cca@gmail.com Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
To have a working display through DPI, a workaround has been
implemented downstream to add "mm_dpi0_dpi0" and "dpi0_sel" to
the DPI node. Shortly, that add an extra clock.
It seems consistent to have the "dpi0_sel" as parent.
Additionnaly, "vpll_dpix" isn't used/managed.
Then, set the "mm_dpi0_dpi0" parent clock to "dpi0_sel".
Use complete parentheses to ensure that macro expansion does
not produce unexpected results.
Fixes: a25d13cbe816 ("RDMA/hns: Add the interfaces to support multi hop addressing for the contexts in hip08") Signed-off-by: Chengchang Tang <tangchengchang@huawei.com> Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com> Link: https://lore.kernel.org/r/20240412091616.370789-10-huangjunxian6@hisilicon.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
GMV's BA table only supports 4K pages. Currently, PAGESIZE is used to
calculate gmv_bt_num, which will cause an abnormal number of gmv_bt_num
in a 64K OS.
Fixes: d6d91e46210f ("RDMA/hns: Add support for configuring GMV table") Signed-off-by: Chengchang Tang <tangchengchang@huawei.com> Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com> Link: https://lore.kernel.org/r/20240412091616.370789-8-huangjunxian6@hisilicon.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The refcount of CQ is not protected by locks. When CQ asynchronous
events and CQ destruction are concurrent, CQ may have been released,
which will cause UAF.
Use the xa_lock() to protect the CQ refcount.
Fixes: 9a4435375cd1 ("IB/hns: Add driver files for hns RoCE driver") Signed-off-by: Chengchang Tang <tangchengchang@huawei.com> Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com> Link: https://lore.kernel.org/r/20240412091616.370789-6-huangjunxian6@hisilicon.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As described in the ib_map_mr_sg function comment, it returns the number
of sg elements that were mapped to the memory region. However,
hns_roce_map_mr_sg returns the number of pages required for mapping the
DMA area. Fix it.
There is no error handling now in __iommu_set_group_pasid(), it relies on
its caller to loop all the devices to undo the pasid attachment. This is
not self-contained and has drawbacks. It would result in unnecessary
remove_dev_pasid() calls on the devices that have not been attached to the
new domain. But the remove_dev_pasid() callback would get the new domain
from the group->pasid_array. So for such devices, the iommu driver won't
find the attachment under the domain, hence unable to do cleanup. This may
not be a real problem today. But it depends on the implementation of the
underlying iommu driver. e.g. the intel iommu driver would warn for such
devices. Such warnings are unnecessary.
To solve the above problem, it is necessary to handle the error within
__iommu_set_group_pasid(). It only loops the devices that have attached
to the new domain, and undo it.
Fixes: 16603704559c ("iommu: Add attach/detach_dev_pasid iommu interfaces") Suggested-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Signed-off-by: Yi Liu <yi.l.liu@intel.com> Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com> Link: https://lore.kernel.org/r/20240328122958.83332-2-yi.l.liu@intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Support for fhctl clocks in apmixedsys was introduced at a later point
and to this moment only one mt6795 based platform has a fhctl DT node
present. Therefore the fhctl support in apmixedsys should be seen as
optional and not cause an error when it is missing.
Change the message's log level to warning. The warning level is chosen
so that it will still alert the fact that fhctl support might be
unintentionally missing, but without implying that this is necessarily
an issue.
Even if the FHCTL DT nodes are added to all current platforms moving
forward, since those changes won't be backported, this ensures stable
kernel releases won't have live with this error.
Fixes: d7964de8a8ea ("clk: mediatek: Add new clock driver to handle FHCTL hardware") Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Link: https://lore.kernel.org/r/20240308-mtk-fhctl-no-node-error-v1-1-51e446eb149a@collabora.com Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently IB_ACCESS_REMOTE_ATOMIC is blocked from being updated via UMR
although in some cases it should be possible. These cases are checked in
mlx5r_umr_can_reconfig function.
umem can be NULL for user application mkeys in some cases. Therefore
umem can't be used for checking if the mkey is cacheable and it is
changed for checking a flag that indicates it. Also make sure that
all mkeys which are not returned to the cache will be destroyed.
As some mkeys can't be modified with UMR due to some UMR limitations,
like the size of translation that can be updated, not all user mkeys can
be cached.
All PLL id values of CMU_TOP were incorrectly set to FOUT_SHARED0_PLL.
It modified to the correct PLL clock id value.
Fixes: 6587c62f69dc ("clk: samsung: add top clock support for Exynos Auto v9 SoC") Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Link: https://lore.kernel.org/r/20240328091000.17660-1-jaewon02.kim@samsung.com Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the source device is operating above 1.5 Gbps per lane, it needs to
send the Skew Calibration Sequence before sending any HS data. If the
DPHY is initialized after the source stream is started, then it might
miss the sequence and not be able to receive data properly. Move the
start of source subdev to the end of the sequence to make sure
everything is ready to receive data before the source starts streaming.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com> Fixes: 3295cf1241d3 ("media: cadence: Add support for external dphy") Tested-by: Julien Massot <julien.massot@collabora.com> Tested-by: Changhuang Liang <Changhuang.liang@starfivetech.com> Reviewed-by: Julien Massot <julien.massot@collabora.com> Reviewed-by: Changhuang Liang <Changhuang.liang@starfivetech.com> Signed-off-by: Jai Luthra <j-luthra@ti.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
DisplayID spec v1.3 revision history notes do claim that
the toplogy block was added in v1.3 so requiring structure
v1.2 would seem correct, but there is at least one EDID in
edid.tv with a topology block and structure v1.0. And
there are also EDIDs with DisplayID structure v1.3 which
seems to be totally incorrect as DisplayID spec v1.3 lists
structure v1.2 as the only legal value.
Unfortunately I couldn't find copies of DisplayID spec
v1.0-v1.2 anywhere (even on vesa.org), so I'll have to
go on empirical evidence alone.
We used to parse the topology block on all v1.x
structures until the check for structure v2.0 was added.
Let's go back to doing that as the evidence does suggest
that there are DisplayIDs in the wild that would miss
out on the topology stuff otherwise.
Also toss out DISPLAY_ID_STRUCTURE_VER_12 entirely as
it doesn't appear we can really use it for anything.
I *think* we could technically skip all the structure
version checks as the block tags shouldn't conflict
between v2.0 and v1.x. But no harm in having a bit of
extra sanity checks I guess.
So far I'm not aware of any user reported regressions
from overly strict check, but I do know that it broke
igt/kms_tiled_display's fake DisplayID as that one
gets generated with structure v1.0.
Cc: Jani Nikula <jani.nikula@intel.com> Cc: Dmitry Osipenko <dmitry.osipenko@collabora.com> Fixes: c5a486af9df7 ("drm/edid: parse Tiled Display Topology Data Block for DisplayID 2.0") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240410180139.21352-1-ville.syrjala@linux.intel.com Acked-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For the cbcr format, gt2 and gt4 are computed again after src_h has been
divided by vsub.
As src_h as already been divided by 2 before, introduce cbcr_src_h and
cbcr_src_w to keep a copy of those values to be used for cbcr gt2 and
gt4 computation.
This fixes yuv planes being unaligned vertically when down scaling to
1080 pixels from 2160.
Logitech Rally Bar devices, despite behaving as UVC cameras, have a
different power management system that the other cameras from Logitech.
USB_QUIRK_RESET_RESUME is applied to all the UVC cameras from Logitech
at the usb core. Unfortunately, USB_QUIRK_RESET_RESUME causes undesired
USB disconnects in the Rally Bar that make them completely unusable.
There is an open discussion about if we should fix this in the core or
add a quirk in the UVC driver. In order to enable this hardware, let's
land this patch first, and we can revert it later if there is a
different conclusion.
The functions mipi_dsi_compression_mode() and
mipi_dsi_picture_parameter_set() return 0-or-error rather than a buffer
size. Follow example of other similar MIPI DSI functions and use int
return type instead of size_t.
These laptops do not have _DSD and must be added by configuration
table, however, the initial entries for them are incorrect:
Neither laptop contains a Speaker ID GPIO.
This issue would not affect audio playback, but may affect which files
are loaded when loading firmware.
The .bpc = 6 implies .bus_format = MEDIA_BUS_FMT_RGB666_1X7X3_SPWG ,
add the missing bus_format. Add missing connector type and bus_flags
as well.
Documentation [1] 1.4 GENERAL SPECIFICATI0NS indicates this panel is
capable of both RGB 18bit/24bit panel, the current configuration uses
18bit mode, .bus_format = MEDIA_BUS_FMT_RGB666_1X7X3_SPWG , .bpc = 6.
Support for the 24bit mode would require another entry in panel-simple
with .bus_format = MEDIA_BUS_FMT_RGB666_1X7X4_SPWG and .bpc = 8, which
is out of scope of this fix.
Previously, the audio status was not updated during detection, leading
to a persistent audio despite hot plugging events. To resolve this
issue, update the audio status during detection.
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 623a3531e9cf ("drm/panel: Add driver for Novatek NT35950 DSI DriverIC panels") Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-8-619a28148e5c@collabora.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Also move the "failed to attach" error message so that it's only printed
when the devm_mipi_dsi_attach() call fails.
Fixes: 6352cd451ddb ("drm: bridge: Add TI DLPC3433 DSI to DMD bridge") Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-7-619a28148e5c@collabora.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: b26975593b17 ("display/drm/bridge: TC358775 DSI/LVDS driver") Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-6-619a28148e5c@collabora.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 0cbbd5b1a012 ("drm: bridge: add support for lontium LT9611UXC bridge") Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-5-619a28148e5c@collabora.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 23278bf54afe ("drm/bridge: Introduce LT9611 DSI to HDMI bridge") Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-4-619a28148e5c@collabora.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 30e2ae943c26 ("drm/bridge: Introduce LT8912B DSI to HDMI bridge") Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-3-619a28148e5c@collabora.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 8dde6f7452a1 ("drm: bridge: icn6211: Add I2C configuration support") Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-2-619a28148e5c@collabora.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 269332997a16 ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found") Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-1-619a28148e5c@collabora.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In malidp_mw_connector_reset, new memory is allocated with kzalloc, but
no check is performed. In order to prevent null pointer dereferencing,
ensure that mw_state is checked before calling
__drm_atomic_helper_connector_reset.
The allocation failure of mycs->yuv_scaler_binary in load_video_binaries()
is followed with a dereference of mycs->yuv_scaler_binary after the
following call chain:
In unload_video_binaries(), it calls to ia_css_binary_unload with argument
&pipe->pipe_settings.video.yuv_scaler_binary[i], which refers to the
same memory slot as mycs->yuv_scaler_binary. Thus, a null-pointer
dereference is triggered.
Link: https://lore.kernel.org/r/20240118151303.3828292-1-alexious@zju.edu.cn Fixes: a49d25364dfb ("staging/atomisp: Add support for the Intel IPU v2") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no reason to prohibit sh7760fb from being built as a
loadable module as suggested by Geert, so change the config symbol
from bool to tristate to allow that and change the FB dependency as
needed.
Fixes: f75f71b2c418 ("fbdev/sh7760fb: Depend on FB=y") Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Javier Martinez Canillas <javierm@redhat.com> Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Helge Deller <deller@gmx.de> Cc: linux-fbdev@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Acked-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Acked-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When support for streams was added to the V4L2 subdev API, the
v4l2_subdev_crop structure was extended with a stream field, but the
field was not handled in the core code that translates the
VIDIOC_SUBDEV_[GS]_CROP ioctls to the selection API. Fix it.
Fixes: 2f91e10ee6fd ("media: subdev: add stream based configuration") Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using __exit for the remove function results in the remove callback
being discarded with CONFIG_VIDEO_ET8EK8=y. When such a device gets
unbound (e.g. using sysfs or hotplug), the driver is just removed
without the cleanup being performed. This results in resource leaks. Fix
it by compiling in the remove callback unconditionally.
Call devm_request_irq() before registering the async notifier, as otherwise
it would be possible to use the device before the interrupts could be
delivered to the driver.
Fixes: c2a6a07afe4a ("media: intel-ipu3: cio2: add new MIPI-CSI2 driver") Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
As documented in the description of the transfer() function of
"struct drm_dp_aux", the transfer() function can be called at any time
regardless of the state of the DP port. Specifically if the kernel has
the DP AUX character device enabled and userspace accesses
"/dev/drm_dp_auxN" directly then the AUX transfer function will be
called regardless of whether a DP device is connected.
For eDP panels we have a special rule where we wait (with a 5 second
timeout) for HPD to go high. This rule was important before all panels
drivers were converted to call wait_hpd_asserted() and actually can be
removed in a future commit.
For external DP devices we never checked for HPD. That means that
trying to access the DP AUX character device (AKA `hexdump -C
/dev/drm_dp_auxN`) would very, very slowly timeout. Specifically on my
system:
$ time hexdump -C /dev/drm_dp_aux0
hexdump: /dev/drm_dp_aux0: Connection timed out
real 0m8.200s
We want access to the drm_dp_auxN character device to fail faster than
8 seconds when no DP cable is plugged in.
Let's add a test to make transfers fail right away if a device isn't
plugged in. Rather than testing the HPD line directly, we have the
dp_display module tell us when AUX transfers should be enabled so we
can handle cases where HPD is signaled out of band like with Type C.
Both dp_link_adjust_levels() and dp_ctrl_update_vx_px() limit swing and
pre-emphasis to 2, while the real maximum value for the sum of the
voltage swing and pre-emphasis is 3. Fix the DP code to remove this
limitation.
Multiple WMI events can be received concurrently, so multiple instances
of xiaomi_wmi_notify() can be active at the same time. Since the input
device is shared between those handlers, the key input sequence can be
disturbed.
Fix this by protecting the key input sequence with a mutex.
Compile-tested only.
Fixes: edb73f4f0247 ("platform/x86: wmi: add Xiaomi WMI key driver") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Link: https://lore.kernel.org/r/20240402143059.8456-2-W_Armin@gmx.de Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In cdns_mhdp_atomic_enable(), the return value of drm_mode_duplicate() is
assigned to mhdp_state->current_mode, and there is a dereference of it in
drm_mode_set_name(), which will lead to a NULL pointer dereference on
failure of drm_mode_duplicate().
Fix this bug add a check of mhdp_state->current_mode.
Fixes: fb43aa0acdfd ("drm: bridge: Add support for Cadence MHDP8546 DPI/DP bridge") Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru> Reviewed-by: Robert Foss <rfoss@kernel.org> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240408125810.21899-1-amishin@t-argos.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
Increase the size of led_names so it can fit any valid v4l2 device name.
Fixes:
drivers/media/radio/radio-shark2.c:197:17: warning: ‘%s’ directive output may be truncated writing up to 35 bytes into a region of size 32 [-Wformat-truncation=]
projects / linux / log