Since commit f8f8f1d04494 ("clk: Don't touch hardware when reparenting
during registration") ULPI has been broken on Tegra20 leading to the
following error message during boot:
[ 1.974698] ulpi_phy_power_on: ulpi write failed
[ 1.979384] tegra-ehci c5004000.usb: Failed to power on the phy
[ 1.985434] tegra-ehci: probe of c5004000.usb failed with error -110
Debugging through the changes and finally also consulting the TRM
revealed that rather than the CDEV2 clock off OSC requiring such pin
muxing actually the PLL_P_OUT4 clock is in use. It looks like so far it
just worked by chance of that one having been enabled which Stephen's
commit now changed when reparenting sclk away from pll_p_out4 leaving
that one disabled. Fix this by properly assigning the PLL_P_OUT4 clock
as the ULPI PHY clock.
During QP creation, the mlx5 driver translates the QP type to an
internal value which is passed on to FW. There was no check to make
sure that the translated value is valid, and -EINVAL was coerced into
the mailbox command.
Current firmware refuses this as an invalid QP type, but future/past
firmware may do something else.
Fixes: 09a7d9eca1a6c ('{net,IB}/mlx5: QP/XRCD commands via mlx5 ifc') Reviewed-by: Ilya Lesokhin <ilyal@mellanox.com> Signed-off-by: Noa Osherovich <noaos@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to make sure compiler flag detection for ARM works
correctly the no-integrated-as flags need to be set before
including the arch specific Makefile.
Fixes: cfe17c9bbe6a ("kbuild: move cc-option and cc-disable-warning after incl. arch Makefile") Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
qla2x00_tmf_sp_done() now deletes the timer that will run
qla2x00_tmf_iocb_timeout(), but doesn't check whether the timer already
expired. Check the return value from del_timer() to avoid calling
complete() a second time.
Fixes: 4440e46d5db7 ("[SCSI] qla2xxx: Add IOCB Abort command asynchronous ...") Fixes: 1514839b3664 ("scsi: qla2xxx: Fix NULL pointer crash due to active ...") Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Removed an error message received when configuring ETS total
bandwidth to be zero.
Our hardware doesn't support such configuration, so we shall
reject it in the driver. Nevertheless, we removed the error message
in order to eliminate error messages caused by old userspace tools
who try to pass such configuration.
For some phy devices, even though they don't support the MMD extended
register access, it does have some side effect if we are trying to
read/write the MMD registers via indirect method. So introduce general
dummy stubs for MMD register access which these devices can use to avoid
such side effect.
Fixes: b6b5e8a69118 ("gianfar: Disable EEE autoneg by default") Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Ethernet on mpc8315erdb is broken since commit b6b5e8a69118
("gianfar: Disable EEE autoneg by default"). The reason is that
even though the rtl8211b doesn't support the MMD extended registers
access, it does return some random values if we trying to access
the MMD register via indirect method. This makes it seem that the
EEE is supported by this phy device. And the subsequent writing to
the MMD registers does cause the phy malfunction. So use the dummy
stubs for the MMD register access to fix this issue.
Fixes: b6b5e8a69118 ("gianfar: Disable EEE autoneg by default") Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since crypto API commit 9fa68f62004 ("crypto: hash - prevent using keyed
hashes without setting key") dm-integrity cannot use keyed algorithms
without the key being set.
The dm-integrity recognizes this too late (during use of HMAC), so it
allows creation and formatting of superblock, but the device is in fact
unusable.
Fix it by detecting the key requirement in integrity table constructor.
Signed-off-by: Milan Broz <gmazyland@gmail.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Adding the vector offset when calling to mlx5_vector2eqn() is wrong.
This is because mlx5_vector2eqn() checks if EQ index is equal to vector number
and the fact that the internal completion vectors that mlx5 allocates
don't get an EQ index.
The second problem here is that using effective_affinity_mask gives the same
CPU for different vectors.
This leads to unmapped queues when calling it from blk_mq_rdma_map_queues().
This doesn't happen when using affinity_hint mask.
Fixes: 2572cf57d75a ("mlx5: fix mlx5_get_vector_affinity to start from completion vector 0") Fixes: 05e0cc84e00c ("net/mlx5: Fix get vector affinity helper function") Signed-off-by: Israel Rukshin <israelr@mellanox.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure to check both return code fields before(!) processing the
command response. Otherwise we risk operating on invalid data.
This matches an earlier fix for SETASSPARMS commands, see
commit ad3cbf613329 ("s390/qeth: fix error handling in checksum cmd callback").
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the allocation of elem fails, it is not sufficient to simply check
for NULL and return. We need to also put our reference on the pool or
else we will leave the pool with a permanent ref count and we will never
be able to free it.
Fixes: 4831ca9e4a8e ("IB/rxe: check for allocation failure on elem") Suggested-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The locking order of vlan_rwsem (LOCK A) and then rtnl (LOCK B),
contradicts other flows such as ipoib_open possibly causing a deadlock.
To prevent this deadlock heavy flush is called with RTNL locked and
only then tries to acquire vlan_rwsem.
This deadlock is possible only when there are child interfaces.
other info that might help us debug this:
[ 141.088967] Possible unsafe locking scenario:
[ 141.094280] CPU0 CPU1
[ 141.097953] ---- ----
[ 141.101640] lock(&priv->vlan_rwsem);
[ 141.104771] lock(rtnl_mutex);
[ 141.109207] lock(&priv->vlan_rwsem);
[ 141.114032] lock(rtnl_mutex);
[ 141.116800]
*** DEADLOCK ***
Fixes: b4b678b06f6e ("IB/ipoib: Grab rtnl lock on heavy flush when calling ndo_open/stop") Signed-off-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As reported by Meelis Roos, my previous patch causes an incorrect
calculation of the timeout, through an undefined signed integer
overflow:
[ 12.228155] UBSAN: Undefined behaviour in drivers/scsi/aacraid/commsup.c:2514:49
[ 12.228229] signed integer overflow:
[ 12.228283] 964297611 * 250 cannot be represented in type 'long int'
The problem is that doing a multiplication with HZ first and then
dividing by USEC_PER_SEC worked correctly for 32-bit microseconds,
but not for 32-bit nanoseconds, which would require up to 41 bits.
This reworks the calculation to first convert the nanoseconds into
jiffies, which should give us the same result as before and not overflow.
Unfortunately I did not understand the exact intention of the algorithm,
in particular the part where we add half a second, so it's possible that
there is still a preexisting problem in this function. I added a comment
that this would be handled more nicely using usleep_range(), which
generally works better for waking up at a particular time than the
current schedule_timeout() based implementation. I did not feel
comfortable trying to implement that without being sure what the
intent is here though.
Fixes: 820f18865912 ("scsi: aacraid: use timespec64 instead of timeval") Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Validate command parsing in acpi_nfit_ctl for the clear error command.
This tests for a crash condition introduced by commit 4b27db7e26cd
"acpi, nfit: add support for the _LSI, _LSR, and _LSW label methods".
Cc: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ucode_major and ucode_minor were swapped. This has
no practical consequences since those fields are not used.
Same goes for umac_major and umac_minor which were only
printed under certain debug flags.
ocfs2_duplicate_clusters_by_page() may crash if one of the extent's pages
is dirty. When a page has not been written back, it is still in dirty
state. If ocfs2_duplicate_clusters_by_page() is called against the dirty
page, the crash happens.
To fix this bug, we can just unlock the page and wait until the page until
its not dirty.
In yam_ioctl(), the concrete ioctl command is firstly copied from the
user-space buffer 'ifr->ifr_data' to 'ioctl_cmd' and checked through the
following switch statement. If the command is not as expected, an error
code EINVAL is returned. In the following execution the buffer
'ifr->ifr_data' is copied again in the cases of the switch statement to
specific data structures according to what kind of ioctl command is
requested. However, after the second copy, no re-check is enforced on the
newly-copied command. Given that the buffer 'ifr->ifr_data' is in the user
space, a malicious user can race to change the command between the two
copies. This way, the attacker can inject inconsistent data and cause
undefined behavior.
This patch adds a re-check in each case of the switch statement if there is
a second copy in that case, to re-check whether the command obtained in the
second copy is the same as the one in the first copy. If not, an error code
EINVAL will be returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In cxgb_extension_ioctl(), the command of the ioctl is firstly copied from
the user-space buffer 'useraddr' to 'cmd' and checked through the
switch statement. If the command is not as expected, an error code
EOPNOTSUPP is returned. In the following execution, i.e., the cases of the
switch statement, the whole buffer of 'useraddr' is copied again to a
specific data structure, according to what kind of command is requested.
However, after the second copy, there is no re-check on the newly-copied
command. Given that the buffer 'useraddr' is in the user space, a malicious
user can race to change the command between the two copies. By doing so,
the attacker can supply malicious data to the kernel and cause undefined
behavior.
This patch adds a re-check in each case of the switch statement if there is
a second copy in that case, to re-check whether the command obtained in the
second copy is the same as the one in the first copy. If not, an error code
EINVAL is returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
the be2net implementation of .ndo_tunnel_{add,del}() changes the value of
NETIF_F_GSO_UDP_TUNNEL bit in 'features' and 'hw_features', but it forgets
to call netdev_features_change(). Moreover, ethtool setting for that bit
can potentially be reverted after a tunnel is added or removed.
GSO already does software segmentation when 'hw_enc_features' is 0, even
if VXLAN offload is turned on. In addition, commit 096de2f83ebc ("benet:
stricter vxlan offloading check in be_features_check") avoids hardware
segmentation of non-VXLAN tunneled packets, or VXLAN packets having wrong
destination port. So, it's safe to avoid flipping the above feature on
addition/deletion of VXLAN tunnels.
Fixes: 630f4b70567f ("be2net: Export tunnel offloads only when a VxLAN tunnel is created") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If requesting b_mutex fails with -EDEADLK, the error variable
is reassigned to the return value from calling ww_mutex_lock
on a_mutex again. If this call fails, a_mutex is not locked.
It is, however, unconditionally unlocked subsequently, causing
the reported warning. Fix the problem by using two error variables.
With this change, the selftest still fails as follows:
cyclic deadlock not resolved, ret[7/8] = -35
However, the traceback is gone.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Fixes: d1b42b800e5d0 ("locking/ww_mutex: Add kselftests for resolving ww_mutex cyclic deadlocks") Link: http://lkml.kernel.org/r/1538516929-9734-1-git-send-email-linux@roeck-us.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
RMNET RX handler was processing invalid packets that were
originally sent on the real device and were looped back via
dev_loopback_xmit(). This was detected using syzkaller.
Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation") Signed-off-by: Sean Tranchetti <stranche@codeaurora.org> Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a commit 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing
continuation lines") regression with the `declance' driver, which caused
the adapter identification message to be split between two lines, e.g.:
declance.c: v0.011 by Linux MIPS DECstation task force
tc6: PMAD-AA
, addr = 08:00:2b:1b:2a:6a, irq = 14
tc6: registered as eth0.
Address that properly, by printing identification with a single call,
making the messages now look like:
declance.c: v0.011 by Linux MIPS DECstation task force
tc6: PMAD-AA, addr = 08:00:2b:1b:2a:6a, irq = 14
tc6: registered as eth0.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Fixes: 4bcc595ccd80 ("printk: reinstate KERN_CONT for printing continuation lines") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
During certain heavy network loads TX could time out
with TX ring dump.
TX is sometimes never restarted after reaching
"tx_stop_threshold" because function "fec_enet_tx_queue"
only tests the first queue.
In addition the TX timeout callback function failed to
recover because it also operated only on the first queue.
Signed-off-by: Rickard x Andersson <rickaran@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In Family 17h, some L3 Cache Performance events require the ThreadMask
and SliceMask to be set. For other events, these fields do not affect
the count either way.
Set ThreadMask and SliceMask to 0xFF and 0xF respectively.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H . Peter Anvin <hpa@zytor.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Suravee <Suravee.Suthikulpanit@amd.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Link: http://lkml.kernel.org/r/Message-ID: Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some of the scheduling tracepoints allow the perf_tp_event
code to write to ring buffer under different cpu than the
code is running on.
This results in corrupted ring buffer data demonstrated in
following perf commands:
# perf record -e 'sched:sched_switch,sched:sched_wakeup' perf bench sched messaging
# Running 'sched/messaging' benchmark:
# 20 sender and receiver processes per group
# 10 groups == 400 processes run
Total time: 0.383 [sec]
[ perf record: Woken up 8 times to write data ]
0x42b890 [0]: failed to process type: -1765585640
[ perf record: Captured and wrote 4.825 MB perf.data (29669 samples) ]
# perf report --stdio
0x42b890 [0]: failed to process type: -1765585640
The reason for the corruption are some of the scheduling tracepoints,
that have __perf_task dfined and thus allow to store data to another
cpu ring buffer:
list_for_each_entry_rcu(event, &ctx->event_list, event_entry) {
if (event->attr.type != PERF_TYPE_TRACEPOINT)
continue;
if (event->attr.config != entry->type)
continue;
perf_swevent_event(event, count, &data, regs);
}
Above code can race with same code running on another cpu,
ending up with 2 cpus trying to store under the same ring
buffer, which is specifically not allowed.
This patch prevents the problem, by allowing only events with the same
current cpu to receive the event.
NOTE: this requires the use of (per-task-)per-cpu buffers for this
feature to work; perf-record does this.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
[peterz: small edits to Changelog] Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andrew Vagin <avagin@openvz.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Fixes: e6dab5ffab59 ("perf/trace: Add ability to set a target task for events") Link: http://lkml.kernel.org/r/20180923161343.GB15054@krava Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
reg_process_hint_country_ie() can free regulatory_request and return
REG_REQ_ALREADY_SET. We shouldn't use regulatory_request after it's
called. KASAN error was observed when this happens.
The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: e0e474a83c18 ("smsc95xx: add wol magic packet support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: 6c636503260d ("smsc75xx: add wol magic packet support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: 21ff2e8976b1 ("r8152: support WOL") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: 19a38d8e0aa3 ("USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver supports a fair amount of Wake-on-LAN modes, but is not
checking that the user specified one that is supported.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Woojung Huh <Woojung.Huh@Microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: e2ca90c276e1 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: 2e55cc7210fe ("[PATCH] USB: usbnet (3/9) module for ASIX Ethernet adapters") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use array_index_nospec() to sanitize i with respect to speculation.
Note that the user doesn't control i directly, but can make it out
of bounds by not finding a threshold in the array.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[add note about user control, as explained by Masashi] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:1713:25: warning: implicit
conversion from enumeration type 'enum tcp_ip_version' to different
enumeration type 'enum qed_tcp_ip_version' [-Wenum-conversion]
cm_info->ip_version = TCP_IPV4;
~ ^~~~~~~~
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:1733:25: warning: implicit
conversion from enumeration type 'enum tcp_ip_version' to different
enumeration type 'enum qed_tcp_ip_version' [-Wenum-conversion]
cm_info->ip_version = TCP_IPV6;
~ ^~~~~~~~
2 warnings generated.
Use the appropriate values from the expected type, qed_tcp_ip_version:
Link: https://github.com/ClangBuiltLinux/linux/issues/125 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when a constant is used in a boolean context as it thinks a
bitwise operation may have been intended.
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: warning: use of logical
'&&' with constant operand [-Wconstant-logical-operand]
if (!p_iov->b_pre_fp_hsi &&
^
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: note: use '&' for a
bitwise operation
if (!p_iov->b_pre_fp_hsi &&
^~
&
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: note: remove constant
to silence this warning
if (!p_iov->b_pre_fp_hsi &&
~^~
1 warning generated.
This has been here since commit 1fe614d10f45 ("qed: Relax VF firmware
requirements") and I am not entirely sure why since 0 isn't a special
case. Just remove the statement causing Clang to warn since it isn't
required.
Link: https://github.com/ClangBuiltLinux/linux/issues/126 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_roce.c:153:12: warning: implicit
conversion from enumeration type 'enum roce_mode' to different
enumeration type 'enum roce_flavor' [-Wenum-conversion]
flavor = ROCE_V2_IPV6;
~ ^~~~~~~~~~~~
drivers/net/ethernet/qlogic/qed/qed_roce.c:156:12: warning: implicit
conversion from enumeration type 'enum roce_mode' to different
enumeration type 'enum roce_flavor' [-Wenum-conversion]
flavor = MAX_ROCE_MODE;
~ ^~~~~~~~~~~~~
2 warnings generated.
Use the appropriate values from the expected type, roce_flavor:
While we're add it, ditch the local variable flavor, we can just return
the value directly from the switch statement.
Link: https://github.com/ClangBuiltLinux/linux/issues/125 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang complains when one enumerated type is implicitly converted to
another.
drivers/net/ethernet/qlogic/qed/qed_vf.c:686:6: warning: implicit
conversion from enumeration type 'enum qed_tunn_mode' to different
enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
QED_MODE_L2GENEVE_TUNN,
^~~~~~~~~~~~~~~~~~~~~~
Update mask's parameter to expect qed_tunn_mode, which is what was
intended.
Link: https://github.com/ClangBuiltLinux/linux/issues/125 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:163:25: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->vxlan.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:165:26: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->l2_gre.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:167:26: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->ip_gre.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:169:29: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->l2_geneve.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:171:29: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->ip_geneve.tun_cls = type;
~ ^~~~
5 warnings generated.
Avoid this by changing type to an int.
Link: https://github.com/ClangBuiltLinux/linux/issues/125 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Crash happened because list_del_rcu() was called twice for smp->ltk. This
was possible if unpair_device was called right after ltk was generated
but before keys were distributed.
In this commit smp_cancel_pairing was refactored to cancel pairing if it
is in progress and otherwise just removes keys. Once keys are removed from
rcu list, pointers to smp context's keys are set to NULL to make sure
removed list items are not accessed later.
This commit also adjusts the functionality of mgmt unpair_device() little
bit. Previously pairing was canceled only if pairing was in state that
keys were already generated. With this commit unpair_device() cancels
pairing already in earlier states.
Bug was found by fuzzing kernel SMP implementation using Synopsys
Defensics.
Reported-by: Pekka Oikarainen <pekka.oikarainen@synopsys.com> Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The allocation of hwsim radio identifiers uses a post-increment from 0,
so the first radio has idx 0. This idx is explicitly excluded from
multicast announcements ever since, but it is unclear why.
Drop that idx check and announce the first radio as well. This makes
userspace happy if it relies on these events.
Signed-off-by: Martin Willi <martin@strongswan.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the qman driver didn't probe, calling qman_alloc_fqid_range,
qman_alloc_pool_range or qman_alloc_cgrid_range (as done in dpaa_eth) will
pass a NULL pointer to gen_pool_alloc, leading to a NULL pointer
dereference.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Reviewed-by: Roy Pledge <roy.pledge@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com>
(cherry picked from commit f72487a2788aa70c3aee1d0ebd5470de9bac953a) Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clear ADDR64 dma bit in DMACFG register in case that HW_DMA_CAP_64B is
not detected on 64bit system.
The issue was observed when bootloader(u-boot) does not check macb
feature at DCFG6 register (DAW64_OFFSET) and enabling 64bit dma support
by default. Then macb driver is reading DMACFG register back and only
adding 64bit dma configuration but not cleaning it out.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
For starters, the bridge netfilter code registers operations that
are invoked any time nh_hook is called. Specifically, ip_sabotage_in
watches for nested calls for NF_INET_PRE_ROUTING when a bridge is in
the stack.
Packet wise, the bridge netfilter hook runs first. br_nf_pre_routing
allocates nf_bridge, sets in_prerouting to 1 and calls NF_HOOK for
NF_INET_PRE_ROUTING. It's finish function, br_nf_pre_routing_finish,
then resets in_prerouting flag to 0 and the packet continues up the
stack. The packet eventually makes it to the VRF driver and it invokes
nf_hook for NF_INET_PRE_ROUTING in case any rules have been added against
the vrf device.
Because of the registered operations the call to nf_hook causes
ip_sabotage_in to be invoked. That function sees the nf_bridge on the
skb and that in_prerouting is not set. Thinking it is an invalid nested
call it steals (drops) the packet.
Update ip_sabotage_in to recognize that the bridge or one of its upper
devices (e.g., vlan) can be enslaved to a VRF (L3 master device) and
allow the packet to go through the nf_hook a second time.
Fixes: 73e20b761acf ("net: vrf: Add support for PREROUTING rules on vrf device") Reported-by: D'Souza, Nelson <ndsouza@ciena.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
XFRM mode parameters passed as part of the user templates
in the IP_XFRM_POLICY are never properly validated. Passing
values other than valid XFRM modes can cause stack-out-of-bounds
reads to occur later in the XFRM processing:
IO_SPACE_LIMIT is the ending address of the PCI IO space, i.e
something like 0xfffff (and not 0x100000).
Therefore, when offset = 0xf0000 is passed as argument, this function
fails even though the offset + SZ_64K fits below the
IO_SPACE_LIMIT. This makes the last chunk of 64 KB of the I/O space
not usable as it cannot be mapped.
This patch fixes that by substracing 1 to offset + SZ_64K, so that we
compare the addrss of the last byte of the I/O space against
IO_SPACE_LIMIT instead of the address of the first byte of what is
after the I/O space.
Fixes: c2794437091a4 ("ARM: Add fixed PCI i/o mapping") Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 222d7dbd258d ("net: prevent dst uses after free")
skb_dst_force() might clear the dst_entry attached to the skb.
The xfrm code don't expect this to happen, so we crash with
a NULL pointer dereference in this case. Fix it by checking
skb_dst(skb) for NULL after skb_dst_force() and drop the packet
in cast the dst_entry was cleared.
Fixes: 222d7dbd258d ("net: prevent dst uses after free") Reported-by: Tobias Hommel <netdev-list@genoetigt.de> Reported-by: Kristian Evensen <kristian.evensen@gmail.com> Reported-by: Wolfgang Walter <linux@stwm.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
TX status reporting to ieee80211s is through ieee80211s_update_metric.
There are two problems about ieee80211s_update_metric:
1. The purpose is to estimate the fail probability
to a specific link. No need to restrict to data frame.
2. Current implementation does not work if wireless driver does not
pass tx_status with skb.
Fix this by removing ieee80211_is_data condition, passing
ieee80211_tx_status directly to ieee80211s_update_metric, and
putting it in both __ieee80211_tx_status and ieee80211_tx_status_ext.
Signed-off-by: Yuan-Chi Pang <fu3mo6goo@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the TDLS setup happens over a connection to an AP that
doesn't have QoS, we nevertheless assign a non-zero TID
(skb->priority) and queue mapping, which may confuse us or
drivers later.
Fix it by just assigning the special skb->priority and then
using ieee80211_select_queue() just like other data frames
would go through.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
cfg80211_get_bss_channel() is used to update the RX channel based on the
available frame payload information (channel number from DSSS Parameter
Set element or HT Operation element). This is needed on 2.4 GHz channels
where frames may be received on neighboring channels due to overlapping
frequency range.
This might of some use on the 5 GHz band in some corner cases, but
things are more complex there since there is no n:1 or 1:n mapping
between channel numbers and frequencies due to multiple different
starting frequencies in different operating classes. This could result
in ieee80211_channel_to_frequency() returning incorrect frequency and
ieee80211_get_channel() returning incorrect channel information (or
indication of no match). In the previous implementation, this could
result in some scan results being dropped completely, e.g., for the 4.9
GHz channels. That prevented connection to such BSSs.
Fix this by using the driver-provided channel pointer if
ieee80211_get_channel() does not find matching channel data for the
channel number in the frame payload and if the scan is done with 5 MHz
or 10 MHz channel bandwidth. While doing this, also add comments
describing what the function is trying to achieve to make it easier to
understand what happens here and why.
In our environment running lots of mesh nodes, we are seeing the
pending queue hang periodically, with the debugfs queues file showing
lines such as:
00: 0x00000000/348
i.e. there are a large number of frames but no stop reason set.
One way this could happen is if queue processing from the pending
tasklet exited early without processing all frames, and without having
some future event (incoming frame, stop reason flag, ...) to reschedule
it.
Exactly this can occur today if ieee80211_tx() returns false due to
packet drops or power-save buffering in the tx handlers. In the
past, this function would return true in such cases, and the change
to false doesn't seem to be intentional. Fix this case by reverting
to the previous behavior.
Fixes: bb42f2d13ffc ("mac80211: Move reorder-sensitive TX handlers to after TXQ dequeue") Signed-off-by: Bob Copeland <bobcopeland@fb.com> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Core regulatory hints didn't set wiphy_idx to WIPHY_IDX_INVALID. Since
the regulatory request is zeroed, wiphy_idx was always implicitly set to
0. This resulted in updating only phy #0.
Fix that.
Fixes: 806a9e39670b ("cfg80211: make regulatory_request use wiphy_idx instead of wiphy") Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[add fixes tag] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We only support one offloaded xfrm (we do not have devices that
can handle more than one offload), so reset crypto_done in
xfrm_input() when iterating over multiple transforms in xfrm_input,
so that we can invoke the appropriate x->type->input for the
non-offloaded transforms
A policy may have been set up with multiple transforms (e.g., ESP
and ipcomp). In this situation, the ingress IPsec processing
iterates in xfrm_input() and applies each transform in turn,
processing the nexthdr to find any additional xfrm that may apply.
This patch resets the transport header back to network header
only after the last transformation so that subsequent xfrms
can find the correct transport header.
After commit d6990976af7c5d8f55903bfb4289b6fb030bf754 ("vti6: fix PMTU caching
and reporting on xmit"), some too big skbs might be potentially passed down to
__xfrm6_output, causing it to fail to transmit but not free the skb, causing a
leak of skb, and consequentially a leak of dst references.
After running pmtu.sh, that shows as failure to unregister devices in a namespace:
[ 311.397671] unregister_netdevice: waiting for veth_b to become free. Usage count = 1
The fix is to call kfree_skb in case of transmit failures.
Fixes: dd767856a36e ("xfrm6: Don't call icmpv6_send on local error") Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We don't validate the address prefix lengths in the xfrm
selector we got from userspace. This can lead to undefined
behaviour in the address matching functions if the prefix
is too big for the given address family. Fix this by checking
the prefixes and refuse SA/policy insertation when a prefix
is invalid.
rvt_destroy_qp() cannot complete until all in process packets have
been released from the underlying hardware. If a link down event
occurs, an application can hang with a kernel stack similar to:
quiesce_qp() waits until all outstanding packets have been freed.
This wait should be momentary. During a link down event, the cleanup
handling does not ensure that all packets caught by the link down are
flushed properly.
This is caused by the fact that the freeze path and the link down
event is handled the same. This is not correct. The freeze path
waits until the HFI is unfrozen and then restarts PIO. A link down
is not a freeze event. The link down path cannot restart the PIO
until link is restored. If the PIO path is restarted before the link
comes up, the application (QP) using the PIO path will hang (until
link is restored).
Fix by separating the linkdown path from the freeze path and use the
link down path for link down events.
Close a race condition sc_disable() by acquiring both the progress
and release locks.
Close a race condition in sc_stop() by moving the setting of the flag
bits under the alloc lock.
Cc: <stable@vger.kernel.org> # 4.9.x+ Fixes: 7724105686e7 ("IB/hfi1: add driver files") Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Gen3, we can only do RXDMA once per transfer reliably. For that, we
must reset the device, then we can have RXDMA once. This patch
implements this. When there is no reset controller or the reset fails,
RXDMA will be blocked completely. Otherwise, it will be disabled after
the first RXDMA transfer. Based on a commit from the BSP by Hiromitsu
Yamasaki, yet completely refactored to handle multiple read messages
within one transfer.
On GLK NUC platforms the HDMI retiming buffer needs additional disabled
time to correctly sync to a faster incoming signal.
When measured on a scope the highspeed lines of the HDMI clock turn off
for ~400uS during a normal resolution change. The HDMI retimer on the
GLK NUC appears to require at least a full frame of quiet time before a
new faster clock can be correctly sync'd. Wait 100ms due to msleep
inaccuracies while waiting for a completed frame. Add a quirk to the
driver for GLK boards that use ITE66317 HDMI retimers.
V2: Add more devices to the quirk list
V3: Delay increased to 100ms, check to confirm crtc type is HDMI.
V4: crtc type check extended to include _DDI and whitespace fixes
v5: Fix white spaces, remove the macro for delay. Revert the crtc type
check introduced in v4.
Cc: Imre Deak <imre.deak@intel.com> Cc: <stable@vger.kernel.org> # v4.14+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105887 Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com> Tested-by: Daniel Scheller <d.scheller.oss@gmail.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180710200205.1478-1-radhakrishna.sripada@intel.com
(cherry picked from commit 90c3e2198777aaa355b6994a31a79c636c8d4306) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We broke the LVDS notifier resume thing in (presumably) commit e2c8b8701e2d ("drm/i915: Use atomic helpers for suspend, v2.") as
we no longer duplicate the current state in the LVDS notifier and
thus we never resume it properly either.
Instead of trying to fix it again let's just kill off the lid
notifier entirely. None of the machines tested thus far have
apparently needed it. Originally the lid notifier was added to
work around cases where the VBIOS was clobbering some of the
hardware state behind the driver's back, mostly on Thinkpads.
We now have a few report of Thinkpads working just fine without
the notifier. So maybe it was misdiagnosed originally, or
something else has changed (ACPI video stuff perhaps?).
If we do end up finding a machine where the VBIOS is still causing
problems I would suggest that we first try setting various bits in
the VBIOS scratch registers. There are several to choose from that
may instruct the VBIOS to steer clear.
With the notifier gone we'll also stop looking at the panel status
in ->detect().
Natanael Copa [Thu, 18 Oct 2018 15:04:17 +0000 (17:04 +0200)]
HID: quirks: fix support for Apple Magic Keyboards
Commit b6cc0ba2cbf4 (HID: add support for Apple Magic Keyboards)
backported support for the Magic Keyboard over Bluetooth, but did not
add the BT_VENDOR_ID_APPLE to hid_have_special_driver[] so the hid-apple
driver is never loaded and Fn key does not work at all.
Adding BT_VENDOR_ID_APPLE to hid_have_special_driver[] is not needed
after commit e04a0442d33b (HID: core: remove the absolute need of
hid_have_special_driver[]), so 4.16 kernels and newer does not need it.
Fixes: b6cc0ba2cbf4 (HID: add support for Apple Magic Keyboards)
Bugzilla-id: https://bugzilla.kernel.org/show_bug.cgi?id=99881 Signed-off-by: Natanael Copa <ncopa@alpinelinux.org> Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's not much sense in doing that because if user or
his build-system didn't set CROSS_COMPILE we still may
very well make incorrect guess.
But as it turned out setting CROSS_COMPILE is not as harmless
as one may think: with recent changes that implemented automatic
discovery of __host__ gcc features unconditional setup of
CROSS_COMPILE leads to failures on execution of "make xxx_defconfig"
with absent cross-compiler, for more info see [1].
Set CROSS_COMPILE as well gets in the way if we want only to build
.dtb's (again with absent cross-compiler which is not really needed
for building .dtb's), see [2].
Note, we had to change LIBGCC assignment type from ":=" to "="
so that is is resolved on its usage, otherwise if it is resolved
at declaration time with missing CROSS_COMPILE we're getting this
error message from host GCC:
| gcc: error: unrecognized command line option -mmedium-calls
| gcc: error: unrecognized command line option -mno-sdata
This check is very naive: we simply test if GCC invoked without
"-mcpu=XXX" has ARC700 define set. In that case we think that GCC
was built with "--with-cpu=arc700" and has libgcc built for ARC700.
Otherwise if ARC700 is not defined we think that everythng was built
for ARCv2.
But in reality our life is much more interesting.
1. Regardless of GCC configuration (i.e. what we pass in "--with-cpu"
it may generate code for any ARC core).
2. libgcc might be built with explicitly specified "--mcpu=YYY"
That's exactly what happens in case of multilibbed toolchains:
- GCC is configured with default settings
- All the libs built for many different CPU flavors
I.e. that check gets in the way of usage of multilibbed
toolchains. And even non-multilibbed toolchains are affected.
OpenEmbedded also builds GCC without "--with-cpu" because
each and every target component later is compiled with explicitly
set "-mcpu=ZZZ".
Jann Horn points out that our TLB flushing was subtly wrong for the
mremap() case. What makes mremap() special is that we don't follow the
usual "add page to list of pages to be freed, then flush tlb, and then
free pages". No, mremap() obviously just _moves_ the page from one page
table location to another.
That matters, because mremap() thus doesn't directly control the
lifetime of the moved page with a freelist: instead, the lifetime of the
page is controlled by the page table locking, that serializes access to
the entry.
As a result, we need to flush the TLB not just before releasing the lock
for the source location (to avoid any concurrent accesses to the entry),
but also before we release the destination page table lock (to avoid the
TLB being flushed after somebody else has already done something to that
page).
This also makes the whole "need_flush" logic unnecessary, since we now
always end up flushing the TLB for every valid entry.
feature fixups need to use patch_instruction() early in the boot,
even before the code is relocated to its final address, requiring
patch_instruction() to use PTRRELOC() in order to address data.
But feature fixups applies on code before it is set to read only,
even for modules. Therefore, feature fixups can use
raw_patch_instruction() instead.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reported-by: David Gounaris <david.gounaris@infinera.com> Tested-by: David Gounaris <david.gounaris@infinera.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI HID devices do not actually have an alias for
them in the IVRS. But dev_data->alias is still used
for indexing into the IOMMU device table for devices
being handled by the IOMMU. So for ACPI HID devices,
we simply return the corresponding devid as an alias,
as parsed from IVRS table.
Current we store the userspace r1 to PACATMSCRATCH before finally
saving it to the thread struct.
In theory an exception could be taken here (like a machine check or
SLB miss) that could write PACATMSCRATCH and hence corrupt the
userspace r1. The SLB fault currently doesn't touch PACATMSCRATCH, but
others do.
We've never actually seen this happen but it's theoretically
possible. Either way, the code is fragile as it is.
This patch saves r1 to the kernel stack (which can't fault) before we
turn MSR[RI] back on. PACATMSCRATCH is still used but only with
MSR[RI] off. We then copy r1 from the kernel stack to the thread
struct once we have MSR[RI] back on.
Suggested-by: Breno Leitao <leitao@debian.org> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we treclaim we store the userspace checkpointed r13 to a scratch
SPR and then later save the scratch SPR to the user thread struct.
Unfortunately, this doesn't work as accessing the user thread struct
can take an SLB fault and the SLB fault handler will write the same
scratch SPRG that now contains the userspace r13.
To fix this, we store r13 to the kernel stack (which can't fault)
before we access the user thread struct.
Found by running P8 guest + powervm + disable_1tb_segments + TM. Seen
as a random userspace segfault with r13 looking like a kernel address.
Signed-off-by: Michael Neuling <mikey@neuling.org> Reviewed-by: Breno Leitao <leitao@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the aspeed MATCH1 register is updated to <current_count -
cycles> in set_next_event handler, with the assumption that COUNT
register value is preserved when the timer is disabled and it continues
decrementing after the timer is enabled. But the assumption is wrong:
RELOAD register is loaded into COUNT register when the aspeed timer is
enabled, which means the next event may be delayed because timer
interrupt won't be generated until <0xFFFFFFFF - current_count +
cycles>.
The problem can be fixed by updating RELOAD register to <cycles>, and
COUNT register will be re-loaded when the timer is enabled and interrupt
is generated when COUNT register overflows.
The test result on Facebook Backpack-CMM BMC hardware (AST2500) shows
the issue is fixed: without the patch, usleep(100) suspends the process
for several milliseconds (and sometimes even over 40 milliseconds);
after applying the fix, usleep(100) takes averagely 240 microseconds to
return under the same workload level.
Signed-off-by: Tao Ren <taoren@fb.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Lei YU <mine260309@gmail.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns that the address of a pointer will always evaluated as true
in a boolean context:
drivers/net/ethernet/mellanox/mlx4/eq.c:243:11: warning: address of
array 'eq->affinity_mask' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!eq->affinity_mask || cpumask_empty(eq->affinity_mask))
~~~~~^~~~~~~~~~~~~
1 warning generated.
Use cpumask_available, introduced in commit f7e30f01a9e2 ("cpumask: Add
helper cpumask_available()"), which does the proper checking and avoids
this warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/86 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sd_init_command() get's a command with a unknown req_op() it crashes the
system via BUG().
This makes debugging the actual reason for the broken request cmd_flags pretty
hard as the system is down before it's able to write out debugging data on the
serial console or the trace buffer.
Change the BUG() to a WARN_ON() and return BLKPREP_KILL to fail gracefully and
return an I/O error to the producer of the request.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Christoph Hellwig <hch@lst.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While dlpar adding primary ipr adapter back, driver goes through adapter
initialization then schedule ipr_worker_thread to start te disk scan by
dropping the host lock, calling scsi_add_device. Then get the adapter reset
request again, so driver does scsi_block_requests, this will cause the
scsi_add_device get hung until we unblock. But we can't run ipr_worker_thread
to do the unblock because its stuck in scsi_add_device.
This patch fixes the issue.
[mkp: typo and whitespace fixes]
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, if userspace calls drm_wait_vblank before the crtc is
activated the crtc vblank_enable hook is called, which in case of
malidp driver triggers some warninngs. This happens because on
device init we don't inform the drm core about the vblank state
by calling drm_crtc_vblank_on/off/reset which together with
drm_vblank_get have some magic that prevents calling drm_vblank_enable
when crtc is off.
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com> Acked-by: Liviu Dudau <liviu.dudau@arm.com> Signed-off-by: Liviu Dudau <liviu.dudau@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When programming the inbound/outbound ATUs, we call usleep_range() after
each checking PCIE_ATU_ENABLE bit. Unfortunately, the ATU programming
can be executed in atomic context:
inbound ATU programming could be called through
pci_epc_write_header()
=>dw_pcie_ep_write_header()
=>dw_pcie_prog_inbound_atu()
outbound ATU programming could be called through
pci_bus_read_config_dword()
=>dw_pcie_rd_conf()
=>dw_pcie_prog_outbound_atu()
EtherAVB hardware requires 0 to be written to status register bits in
order to clear them, however, care must be taken not to:
1. Clear other bits, by writing zero to them
2. Write one to reserved bits
This patch corrects the ravb driver with respect to the second point above.
This is done by defining reserved bit masks for the affected registers and,
after auditing the code, ensure all sites that may write a one to a
reserved bit use are suitably masked.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the Netgear WNDAP620, the emac ethernet isn't receiving nor
xmitting any frames from/to the RTL8363SB (identifies itself
as a RTL8367RB).
This is caused by the emac hardware not knowing the forced link
parameters for speed, duplex, pause, etc.
This begs the question, how this was working on the original
driver code, when it was necessary to set the phy_address and
phy_map to 0xffffffff. But I guess without access to the old
PPC405/440/460 hardware, it's not possible to know.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While reviewing another part of the code, Kees noticed that the strncpy of the
partition name might not always be NUL terminated. Switch to using strscpy
which does this safely.
Reported-by: Kees Cook <keescook@chromium.org> Signed-off-by: Laura Abbott <labbott@redhat.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardif_neigh refcounter is to be decreased by the queued work and
currently is never decreased if the queue_work() call fails.
Fix by checking the queue_work() return value and decrease refcount
if necessary.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The backbone_gw refcounter is to be decreased by the queued work and
currently is never decreased if the queue_work() call fails.
Fix by checking the queue_work() return value and decrease refcount
if necessary.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux / log