The logic was broken as it failed to update the response length for
architectures with PAGE_SIZE larger than 4kB. As a result further
extension of the ucontext response struct would fail.
Fixes: d69e3bcf7976 ('IB/mlx5: Mmap the HCA's core clock register to user-space') Signed-off-by: Eli Cohen <eli@mellanox.com> Reviewed-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should be allocating enough information for a tiadc_device struct
which is about 400 bytes but instead we allocate enough for a second
iio_dev struct which is over 2000 bytes.
Fixes: fea89e2dfcea ("iio: adc: ti_am335x_adc: use variable names for sizeof() operator") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the datasheet the RCO must be recalibrated
on every power-on-reset. Also remove mutex locking in the
calibration function since callers other than the probe
function (which doesn't need it) will have a lock.
Fixes: 24ddb0e4bba4 ("iio: Add AS3935 lightning sensor support") Cc: George McCollister <george.mccollister@gmail.com> Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Datasheet of each device (lps331ap, lps25h, lps001wp, lps22hb) says that
the pressure and temperature data is a 2's complement.
I'm sending this the slow way, as negative pressures on these are pretty
unusual and the nature of the fixing of multiple device introduction patches
will make it hard to apply to older kernels - Jonathan.
Fixes: 217494e5b780 ("iio:pressure: Add STMicroelectronics pressures driver") Fixes: 2f5effcbd097 ("iio: pressure-core: st: Expand and rename LPS331AP's channel descriptor") Fixes: 7885a8ce6800 ("iio: pressure: st: Add support for new LPS001WP pressure sensor") Fixes: e039e2f5b4da ("iio:st_pressure:initial lps22hb sensor support") Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Standard deviation is calculated as the square root of the variance
where variance is the mean of sample_sum and length. Correct the
computation of statP->stddev in accordance to the proper calculation.
Commit 16fa3dc75c22 ("mfd: omap-usb-tll: HOST TLL platform driver")
added support for USB TLL, but uses OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF
bit the wrong way. The comments in the code are correct, but the inverted
use of OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF causes the register to be
enabled instead of disabled unlike what the comments say.
Without this change the Wrigley 3G LTE modem on droid 4 EHCI bus can
be only pinged few times before it stops responding.
Fixes: 16fa3dc75c22 ("mfd: omap-usb-tll: HOST TLL platform driver") Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'__vmalloc_start_set' currently only gets set in initmem_init() when
!CONFIG_NEED_MULTIPLE_NODES. This breaks detection of vmalloc address
with virt_addr_valid() with CONFIG_NEED_MULTIPLE_NODES=y, causing
a kernel crash:
[mm/usercopy] 517e1fbeb6: kernel BUG at arch/x86/mm/physaddr.c:78!
Set '__vmalloc_start_set' appropriately for that case as well.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Laura Abbott <labbott@redhat.com> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: dc16ecf7fd1f ("x86-32: use specific __vmalloc_start_set flag in __virt_addr_valid") Link: http://lkml.kernel.org/r/1494278596-30373-1-git-send-email-labbott@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When changing hardware control flow for a UART with dedicated RTS/CTS
pins, the new AUTORTS state is not immediately reflected in the
hardware, but only when RTS is raised. However, the serial core does
not call .set_mctrl() after .set_termios(), hence AUTORTS may only
become effective when the port is closed, and reopened later.
Note that this problem does not happen when manually using stty to
change CRTSCTS, as AUTORTS will work fine on next open.
To fix this, call .set_mctrl() from .set_termios() when dedicated
RTS/CTS pins are present, to refresh the AUTORTS or RTS state.
This is similar to what other drivers supporting AUTORTS do (e.g.
omap-serial).
Reported-by: Baumann, Christoph (C.) <cbaumann@visteon.com> Fixes: 33f50ffc253854cf ("serial: sh-sci: Fix support for hardware-assisted RTS/CTS") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UARTn_FRAME_PARITY_ODD is 0x0300
UARTn_FRAME_PARITY_EVEN is 0x0200
So if the UART is configured for EVEN parity, it would be reported as ODD.
Fix it by correctly testing if the 2 bits are set.
If a CMA allocation failed, the partially constructed BO would be
unreferenced through the normal path, and we might choose to put it in
the BO cache. If we then reused it before it expired from the cache,
the kernel would OOPS.
mtk_hdmi_setup_vendor_specific_infoframe will return before handle
mtk_hdmi_hw_send_info_frame.Because hdmi_vendor_infoframe_pack
returns the number of bytes packed into the binary buffer or
a negative error code on failure.
So correct it.
Fixes: 8f83f26891e1 ("drm/mediatek: Add HDMI support") Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com> Signed-off-by: CK Hu <ck.hu@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mac80211 allows to modify the SMPS state of an AP both,
when it is started, and after it has been started. Such a
change will trigger an action frame to all the peers that
are currently connected, and will be remembered so that
new peers will get notified as soon as they connect (since
the SMPS setting in the beacon may not be the right one).
This means that we need to remember the SMPS state
currently requested as well as the SMPS state that was
configured initially (and advertised in the beacon).
The former is bss->req_smps and the latter is
sdata->smps_mode.
Initially, the AP interface could only be started with
SMPS_OFF, which means that sdata->smps_mode was SMPS_OFF
always. Later, a nl80211 API was added to be able to start
an AP with a different AP mode. That code forgot to update
bss->req_smps and because of that, if the AP interface was
started with SMPS_DYNAMIC, we had:
sdata->smps_mode = SMPS_DYNAMIC
bss->req_smps = SMPS_OFF
That configuration made mac80211 think it needs to fire off
an action frame to any new station connecting to the AP in
order to let it know that the actual SMPS configuration is
SMPS_OFF.
Fix that by properly setting bss->req_smps in
ieee80211_start_ap.
Fixes: f69931748730 ("mac80211: set smps_mode according to ap params") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the commit enabling per-CPU station statistics, I inadvertedly
copy-pasted some code to update rx_packets and forgot to change it
to update rx_dropped_misc. Fix that.
This addresses https://bugzilla.kernel.org/show_bug.cgi?id=195953.
Fixes: c9c5962b56c1 ("mac80211: enable collecting station statistics per-CPU") Reported-by: Petru-Florin Mihancea <petrum@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mesh forwarding path checks for address extension mode to fetch
appropriate proxied address and MPP address. Existing condition
that looks for 6 address format is not strict enough so that
frames with improper values are processed and invalid entries
are added into MPP table. Fix that by adding a stricter check before
processing the packet.
Per IEEE Std 802.11s-2011 spec. Table 7-6g1 lists address extension
mode 0x3 as reserved one. And also Table Table 9-13 does not specify
0x3 as valid address field.
Fixes: 9b395bc3be1c ("mac80211: verify that skb data is present") Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When VHT IBSS support was added, the size of the extra elements
wasn't considered in ieee80211_ibss_build_presp(), which makes
it possible that it would overrun the allocated buffer. Fix it
by allocating the necessary space.
Fixes: abcff6ef01f9 ("mac80211: add VHT support for IBSS") Reported-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When adding per-CPU statistics, which added statistics back
to mac80211 for the fast-RX path, I evidently forgot to add
the "stats->packets++" line. The reason for that is likely
that I didn't see it since it's done in defragmentation for
the regular RX path.
Add the missing line to properly count received packets in
the fast-RX case.
Fixes: c9c5962b56c1 ("mac80211: enable collecting station statistics per-CPU") Reported-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing IBSS capability flag during capability init as it needs
to be inserted into the generated beacon in order for CSA to work.
Fixes: cd7760e62c2ac ("mac80211: add support for CSA in IBSS mode") Signed-off-by: Piotr Gawlowicz <gawlowicz@tkn.tu-berlin.de> Signed-off-by: Mikołaj Chwalisz <chwalisz@tkn.tu-berlin.de> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently VBUS is turned off while a usb device is detached, and turned
on again by the polling routine. This short period VBUS loss prevents
usb modem to switch mode.
VBUS should be constantly on for host-only mode, so this changes the
driver to not turn off VBUS for host-only mode.
Fixes: 2f3fd2c5bde1 ("usb: musb: Prepare dsps glue layer for PM runtime support") Reported-by: Moreno Bartalucci <moreno.bartalucci@tecnorama.it> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current it's strictly checked if PVINFO version matches 1.0
for GVT-g i915 guest which doesn't help for compatibility at
all and forces GVT-g host can't extend PVINFO easily with version
bump for real compatibility check.
This fixes that to check minimal required PVINFO version instead.
v2:
- drop unneeded version macro
- use only major version for sanity check
v3:
- fix up PVInfo value with kernel type
- one indent fix
Commit d63c277dc672e0
("drm/amdgpu: Make display watermark calculations more accurate")
made watermark calculations more accurate, but not for > 4k
resolutions on 32-Bit architectures, as it introduced an integer
overflow for those setups and resolutions.
Fix this by proper u64 casting and division.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Fixes: d63c277dc672 ("drm/amdgpu: Make display watermark calculations more accurate") Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise, we enable all sorts of forgeries via timing attack.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: linux-wireless@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 27ed3cd2ebf4 (cpufreq: conservative: Fix the logic in frequency
decrease checking) removed the 10 point substraction when comparing the
load against down_threshold but did not remove the related limit for the
down_threshold value. As a result, down_threshold lower than 11 is not
allowed even though values from 1 to 10 do work correctly too. The
comment ("cannot be lower than 11 otherwise freq will not fall") also
does not apply after removing the substraction.
For this reason, allow down_threshold to take any value from 1 to 99
and fix the related comment.
Fixes: 27ed3cd2ebf4 (cpufreq: conservative: Fix the logic in frequency decrease checking) Signed-off-by: Tomasz Wilczyński <twilczynski@naver.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While discussing the possible merits of clang warning about unused initialized
functions, I found one function that was clearly meant to be called but
never actually is.
__ila_hash_secret_init() initializes the hash value for the ila locator,
apparently this is intended to prevent hash collision attacks, but this ends
up being a read-only zero constant since there is no caller. I could find
no indication of why it was never called, the earliest patch submission
for the module already was like this. If my interpretation is right, we
certainly want to backport the patch to stable kernels as well.
I considered adding it to the ila_xlat_init callback, but for best effect
the random data is read as late as possible, just before it is first used.
The underlying net_get_random_once() is already highly optimized to avoid
overhead when called frequently.
Fixes: 7f00feaf1076 ("ila: Add generic ILA translation facility") Link: https://www.spinics.net/lists/kernel/msg2527243.html Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch closes a long standing race in configfs between
the creation of a new symlink in create_link(), while the
symlink target's config_item is being concurrently removed
via configfs_rmdir().
This can happen because the symlink target's reference
is obtained by config_item_get() in create_link() before
the CONFIGFS_USET_DROPPING bit set by configfs_detach_prep()
during configfs_rmdir() shutdown is actually checked..
This originally manifested itself on ppc64 on v4.8.y under
heavy load using ibmvscsi target ports with Novalink API:
My static checker complains that if "lvl" is ULONG_MAX (this is 64 bit)
then some of the strings will overflow. I don't know if that's possible
but it seems simple enough to make the buffers slightly larger.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Waldemar Brodkorb <wbx@openadk.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems there can be a race condition in which no crtc state is
added to the first atomic commit. This results in all crtc's having a
null DDB allocation, causing a FIFO underrun on any update until the
first modeset.
Changes since v1:
- Do not take the connection_mutex, this is already done below.
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Inspired-by: Mahesh Kumar <mahesh1.kumar@intel.com> Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Fixes: 98d39494d375 ("drm/i915/gen9: Compute DDB allocation at atomic
check time (v4)") Cc: Mahesh Kumar <mahesh1.kumar@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170531154236.27180-1-maarten.lankhorst@linux.intel.com Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 367d73d2806085bb507ab44c1f532640917fd5ca) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The scanline counter is bonkers on VLV/CHV DSI. The scanline counter
increment is not lined up with the start of vblank like it is on
every other platform and output type. This causes problems for
both the vblank timestamping and atomic update vblank evasion.
On my FFRD8 machine at least, the scanline counter increment
happens about 1/3 of a scanline ahead of the start of vblank (which
is where all register latching happens still). That means we can't
trust the scanline counter to tell us whether we're in vblank or not
while we're on that particular line. In order to keep vblank
timestamping in working condition when called from the vblank irq,
we'll leave scanline_offset at one, which means that the entire
line containing the start of vblank is considered to be inside
the vblank.
For the vblank evasion we'll need to consider that entire line
to be bad, since we can't tell whether the registers already
got latched or not. And we can't actually use the start of vblank
interrupt to get us past that line as the interrupt would fire
too soon, and then we'd up waiting for the next start of vblank
instead. One way around that would using the frame start
interrupt instead since that wouldn't fire until the next
scanline, but that would require some bigger changes in the
interrupt code. So for simplicity we'll just poll until we get
past the bad line.
v2: Adjust the comments a bit
Cc: Jonas Aaberg <cja@gmx.net> Tested-by: Jonas Aaberg <cja@gmx.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99086 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20161215174734.28779-1-ville.syrjala@linux.intel.com Tested-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com>
(cherry picked from commit ec1b4ee2834e66884e5b0d3d465f347ff212e372) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For most cases a protection exception in the host (e.g. copy
on write or dirty tracking) on the sie instruction will indicate
an instruction length of 4. Turns out that there are some corner
cases (e.g. runtime instrumentation) where this is not necessarily
true and the ILC is unpredictable.
Let's replace our 4 byte rewind_pad with 3 byte nops to prepare for
all possible ILCs.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linux IRQ #0 is reserved for error reporting and may not be used.
Increase NR_IRQS for one additional slot and increase
irq_domain_add_legacy parameter first_irq value to 1, so that linux
IRQ #0 is not associated with hardware IRQ #0 in legacy IRQ domains.
Introduce macro XTENSA_PIC_LINUX_IRQ for static translation of xtensa
PIC hardware IRQ # to linux IRQ #. Use this macro in XTFPGA platform
data definitions.
This fixes inability to use hardware IRQ #0 in configurations that don't
use device tree and allows for non-identity mapping between linux IRQ #
and hardware IRQ #.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Relying on qede to trigger qedr on startup is problematic. When probing
both if qedr loads slowly then qede can assume qedr is missing and not
trigger it. This patch adds a triggering from qedr and protects against
a race via an atomic bit.
First, log prefix will be truncated to NF_LOG_PREFIXLEN-1, i.e. 127,
at nf_log_packet(), so the extra part is useless.
Second, after adding a log rule with a very very long prefix, we will
fail to dump the nft rules after this _special_ one, but acctually,
they do exist. For example:
# name_65000=$(printf "%0.sQ" {1..65000})
# nft add rule filter output log prefix "$name_65000"
# nft add rule filter output counter
# nft add rule filter output counter
# nft list chain filter output
table ip filter {
chain output {
type filter hook output priority 0; policy accept;
}
}
So now, restrict the log prefix length to NF_LOG_PREFIXLEN-1.
If the element exists and no NLM_F_EXCL is specified, do not bump
set->nelems, otherwise we leak one set element slot. This problem
amplifies if the set is full since the abort path always decrements the
counter for the -ENFILE case too, giving one spare extra slot.
Fix this by moving set->nelems update to nft_add_set_elem() after
successful element insertion. Moreover, remove the element if the set is
full so there is no need to rely on the abort path to undo things
anymore.
Fixes: c016c7e45ddf ("netfilter: nf_tables: honor NLM_F_EXCL flag in set element insertion") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We trigger a soft lockup as we grab nametbl_lock twice if the node
has a pending node up/down or link up/down event while:
- we process an incoming named message in tipc_named_rcv() and
perform an tipc_update_nametbl().
- we have pending backlog items in the name distributor queue
during a nametable update using tipc_nametbl_publish() or
tipc_nametbl_withdraw().
The following are the call chain associated:
tipc_named_rcv() Grabs nametbl_lock
tipc_update_nametbl() (publish/withdraw)
tipc_node_subscribe()/unsubscribe()
tipc_node_write_unlock()
<< lockup occurs if an outstanding node/link event
exits, as we grabs nametbl_lock again >>
tipc_nametbl_withdraw() Grab nametbl_lock
tipc_named_process_backlog()
tipc_update_nametbl()
<< rest as above >>
The function tipc_node_write_unlock(), in addition to releasing the
lock processes the outstanding node/link up/down events. To do this,
we need to grab the nametbl_lock again leading to the lockup.
In this commit we fix the soft lockup by introducing a fast variant of
node_unlock(), where we just release the lock. We adapt the
node_subscribe()/node_unsubscribe() to use the fast variants.
Reported-and-Tested-by: John Thompson <thompa.atl@gmail.com> Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until now, the subscribers keep track of the subscriptions using
reference count at subscriber level. At subscription cancel or
subscriber delete, we delete the subscription only if the timer
was pending for the subscription. This approach is incorrect as:
1. del_timer() is not SMP safe, if on CPU0 the check for pending
timer returns true but CPU1 might schedule the timer callback
thereby deleting the subscription. Thus when CPU0 is scheduled,
it deletes an invalid subscription.
2. We export tipc_subscrp_report_overlap(), which accesses the
subscription pointer multiple times. Meanwhile the subscription
timer can expire thereby freeing the subscription and we might
continue to access the subscription pointer leading to memory
violations.
In this commit, we introduce subscription refcount to avoid deleting
an invalid subscription.
Reported-and-Tested-by: John Thompson <thompa.atl@gmail.com> Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until now, the generic server framework maintains the connection
id's per subscriber in server's conn_idr. At tipc_close_conn, we
remove the connection id from the server list, but the connection is
valid until we call the refcount cleanup. Hence we have a window
where the server allocates the same connection to an new subscriber
leading to inconsistent reference count. We have another refcount
warning we grab the refcount in tipc_conn_lookup() for connections
with flag with CF_CONNECTED not set. This usually occurs at shutdown
when the we stop the topology server and withdraw TIPC_CFG_SRV
publication thereby triggering a withdraw message to subscribers.
In this commit, we:
1. remove the connection from the server list at recount cleanup.
2. grab the refcount for a connection only if CF_CONNECTED is set.
Tested-by: John Thompson <thompa.atl@gmail.com> Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In tipc_conn_sendmsg(), we first queue the request to the outqueue
followed by the connection state check. If the connection is not
connected, we should not queue this message.
In this commit, we reject the messages if the connection state is
not CF_CONNECTED.
Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Tested-by: John Thompson <thompa.atl@gmail.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed on HS38 cores, for setting up IO-Coherency aperture properly
The polling could perturb the caches and coherecy fabric which could be
wrong in the small window when Master is setting up IOC aperture etc
in arc_cache_init()
We do it only for ARCv2 based builds to not affect EZChip ARCompact
based platform.
For run-on-reset SMP configs, non master cores call a routine which
waits until Master gives it a "go" signal (currently using a shared
mem flag). The same routine then jumps off the well known entry point of
all non Master cores i.e. @first_lines_of_secondary
This patch moves out the last part into one single place in early boot
code.
This is better in terms of absraction (the wait API only waits) and
returns, leaving out the "jump off to" part.
In actual implementation this requires some restructuring of the early
boot code as well as Master now jumps to BSS setup explicitly,
vs. falling thru into it before.
Technically this patch doesn't cause any functional change, it just
moves the ugly #ifdef'ry from assembly code to "C"
On an overloaded system, it is possible that a change in the watchdog
threshold can be delayed long enough to trigger a false positive.
This can easily be achieved by having a cpu spinning indefinitely on a
task, while another cpu updates watchdog threshold.
What happens is while trying to park the watchdog threads, the hrtimers
on the other cpus trigger and reprogram themselves with the new slower
watchdog threshold. Meanwhile, the nmi watchdog is still programmed
with the old faster threshold.
Because the one cpu is blocked, it prevents the thread parking on the
other cpus from completing, which is needed to shutdown the nmi watchdog
and reprogram it correctly. As a result, a false positive from the nmi
watchdog is reported.
Fix this by setting a park_in_progress flag to block all lockups until
the parking is complete.
This is an attempt to cleanup watchdog handlers. Right now,
kernel/watchdog.c implements both softlockup and hardlockup detectors.
Softlockup code is generic. Hardlockup code is arch specific. Some
architectures don't use hardlockup detectors. They use their own
watchdog detectors. To make both these combination work, we have
numerous #ifdefs in kernel/watchdog.c.
We are trying here to make these handlers independent of each other.
Also provide an interface for architectures to implement their own
handlers. watchdog_nmi_enable and watchdog_nmi_disable will be defined
as weak such that architectures can override its definitions.
Thanks to Don Zickus for his suggestions.
Here are our previous discussions
http://www.spinics.net/lists/sparclinux/msg16543.html
http://www.spinics.net/lists/sparclinux/msg16441.html
This patch (of 3):
Move shared macros and definitions to nmi.h so that watchdog.c, new file
watchdog_hld.c or any other architecture specific handler can use those
definitions.
Separate hardlockup code from watchdog.c and move it to watchdog_hld.c.
It is mostly straight forward. Remove everything inside
CONFIG_HARDLOCKUP_DETECTORS. This code will go to file watchdog_hld.c.
Also update the makefile accordigly.
With >=32 CPUs the userfaultfd selftest triggered a graceful but
unexpected SIGBUS because VM_FAULT_RETRY was returned by
handle_userfault() despite the UFFDIO_COPY wasn't completed.
This seems caused by rwsem waking the thread blocked in
handle_userfault() and we can't run up_read() before the wait_event
sequence is complete.
Keeping the wait_even sequence identical to the first one, would require
running userfaultfd_must_wait() again to know if the loop should be
repeated, and it would also require retaking the rwsem and revalidating
the whole vma status.
It seems simpler to wait the targeted wakeup so that if false wakeups
materialize we still wait for our specific wakeup event, unless of
course there are signals or the uffd was released.
Debug code collecting the stack trace of the wakeup showed this:
This always happens when the main userfault selftest thread is running
clone() while glibc runs either mprotect or mmap (both taking mmap_sem
down_write()) to allocate the thread stack of the background threads,
while locking/userfault threads already run at full throttle and are
susceptible to false wakeups that may cause handle_userfault() to return
before than expected (which results in graceful SIGBUS at the next
attempt).
This was reproduced only with >=32 CPUs because the loop to start the
thread where clone() is too quick with fewer CPUs, while with 32 CPUs
there's already significant activity on ~32 locking and userfault
threads when the last background threads are started with clone().
This >=32 CPUs SMP race condition is likely reproducible only with the
selftest because of the much heavier userfault load it generates if
compared to real apps.
We'll have to allow "one more" VM_FAULT_RETRY for the WP support and a
patch floating around that provides it also hidden this problem but in
reality only is successfully at hiding the problem.
False wakeups could still happen again the second time
handle_userfault() is invoked, even if it's a so rare race condition
that getting false wakeups twice in a row is impossible to reproduce.
This full fix is needed for correctness, the only alternative would be
to allow VM_FAULT_RETRY to be returned infinitely. With this fix the WP
support can stick to a strict "one more" VM_FAULT_RETRY logic (no need
of returning it infinite times to avoid the SIGBUS).
Link: http://lkml.kernel.org/r/20170111005535.13832-2-aarcange@redhat.com Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Shubham Kumar Sharma <shubham.kumar.sharma@oracle.com> Tested-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Michael Rapoport <RAPOPORT@il.ibm.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8a59f5d25265 ("fs/romfs: return f_fsid for statfs(2)") generates
a 64bit id from sb->s_bdev->bd_dev. This is only correct when romfs is
defined with CONFIG_ROMFS_ON_BLOCK. If romfs is only defined with
CONFIG_ROMFS_ON_MTD, sb->s_bdev is NULL, referencing sb->s_bdev->bd_dev
will triger an oops.
Richard Weinberger points out that when CONFIG_ROMFS_BACKED_BY_BOTH=y,
both CONFIG_ROMFS_ON_BLOCK and CONFIG_ROMFS_ON_MTD are defined.
Therefore when calling huge_encode_dev() to generate a 64bit id, I use
the follow order to choose parameter,
- CONFIG_ROMFS_ON_BLOCK defined
use sb->s_bdev->bd_dev
- CONFIG_ROMFS_ON_BLOCK undefined and CONFIG_ROMFS_ON_MTD defined
use sb->s_dev when,
- both CONFIG_ROMFS_ON_BLOCK and CONFIG_ROMFS_ON_MTD undefined
leave id as 0
When CONFIG_ROMFS_ON_MTD is defined and sb->s_mtd is not NULL, sb->s_dev
is set to a device ID generated by MTD_BLOCK_MAJOR and mtd index,
otherwise sb->s_dev is 0.
This is a try-best effort to generate a uniq file system ID, if all the
above conditions are not meet, f_fsid of this romfs instance will be 0.
Generally only one romfs can be built on single MTD block device, this
method is enough to identify multiple romfs instances in a computer.
Link: http://lkml.kernel.org/r/1482928596-115155-1-git-send-email-colyli@suse.de Signed-off-by: Coly Li <colyli@suse.de> Reported-by: Nong Li <nongli1031@gmail.com> Tested-by: Nong Li <nongli1031@gmail.com> Cc: Richard Weinberger <richard.weinberger@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sctp_addr_id2transport is a function for sockopt to look up assoc by
address. As the address is from userspace, it can be a v4-mapped v6
address. But in sctp protocol stack, it always handles a v4-mapped
v6 address as a v4 address. So it's necessary to convert it to a v4
address before looking up assoc by address.
This patch is to fix it by calling sctp_verify_addr in which it can do
this conversion before calling sctp_endpoint_lookup_assoc, just like
what sctp_sendmsg and __sctp_connect do for the address from users.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now sctp gso puts segments into skb's frag_list, then processes these
segments in skb_segment. But skb_segment handles them only when gs is
enabled, as it's in the same branch with skb's frags.
Although almost all the NICs support sg other than some old ones, but
since commit 1e16aa3ddf86 ("net: gso: use feature flag argument in all
protocol gso handlers"), features &= skb->dev->hw_enc_features, and
xfrm_output_gso call skb_segment with features = 0, which means sctp
gso would call skb_segment with sg = 0, and skb_segment would not work
as expected.
This patch is to fix it by setting features param with NETIF_F_SG when
calling skb_segment so that it can go the right branch to process the
skb's frag_list.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bnxt_get_port_module_status() calls bnxt_update_link() which expects
RTNL to be held. In bnxt_sp_task() that does not hold RTNL, we need to
call it with a prior call to bnxt_rtnl_lock_sp() and the call needs to
be moved to the end of bnxt_sp_task().
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bnxt_update_link() is called from multiple code paths. Most callers,
such as open, ethtool, already hold RTNL. Only the caller bnxt_sp_task()
does not. So it is a bug to take RTNL inside bnxt_update_link().
Fix it by removing the RTNL inside bnxt_update_link(). The function
now expects the caller to always hold RTNL.
In bnxt_sp_task(), call bnxt_rtnl_lock_sp() before calling
bnxt_update_link(). We also need to move the call to the end of
bnxt_sp_task() since it will be clearing the BNXT_STATE_IN_SP_TASK bit.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some dual port NICs, the speed setting on one port can affect the
available speed on the other port. Add logic to detect these changes
and adjust the advertised speed settings when necessary.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In bnxt_sp_task(), we set a bit BNXT_STATE_IN_SP_TASK so that bnxt_close()
will synchronize and wait for bnxt_sp_task() to finish. Some functions
in bnxt_sp_task() require us to clear BNXT_STATE_IN_SP_TASK and then
acquire rtnl_lock() to prevent race conditions.
There are some bugs related to this logic. This patch refactors the code
to have common bnxt_rtnl_lock_sp() and bnxt_rtnl_unlock_sp() to handle
the RTNL and the clearing/setting of the bit. Multiple functions will
need the same logic. We also need to move bnxt_reset() to the end of
bnxt_sp_task(). Functions that clear BNXT_STATE_IN_SP_TASK must be the
last functions to be called in bnxt_sp_task(). The common scheme will
handle the condition properly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the binding was defined, I was not aware that mt2701 was an earlier
version of the SoC. For sake of consistency, the ethernet driver should
use mt2701 inside the compat string as this is the earliest SoC with the
ethernet core.
The ethernet driver is currently of no real use until we finish and
upstream the DSA driver. There are no users of this binding yet. It should
be safe to fix this now before it is too late and we need to provide
backward compatibility for the mt7623-eth compat string.
Reported-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop the tx when the napi is disabled to prevent napi_schedule() is
called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rtl8152_post_reset() should sumbit rx urb and interrupt transfer,
otherwise the rx wouldn't work and the linking change couldn't be
detected.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Re-schedule napi after napi_complete() for tx, if it is necessay.
In r8152_poll(), if the tx is completed after tx_bottom() and before
napi_complete(), the scheduling of napi would be lost. Then, no
one handles the next tx until the next napi_schedule() is called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Schedule the napi after napi_enable() for rx, if it is necessary.
If the rx is completed when napi is disabled, the sheduling of napi
would be lost. Then, no one handles the rx packet until next napi
is scheduled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust the setting of the flag of SELECTIVE_SUSPEND to prevent start_xmit()
from calling napi_schedule() directly during runtime suspend.
After calling napi_disable() or clearing the flag of WORK_ENABLE,
scheduling the napi is useless.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch performs dma sync operations on nvme_command
and nvme_completion.
nvme_command is synced
(a) on receiving of the recv queue completion for cpu access.
(b) before posting recv wqe back to rdma adapter for device access.
nvme_completion is synced
(a) on receiving of the recv queue completion of associated
nvme_command for cpu access.
(b) before posting send wqe to rdma adapter for device access.
This patch is generated for git://git.infradead.org/nvme-fabrics.git
Branch: nvmf-4.10
Lock sequence IDs are bumped in decode_lock by calling
nfs_increment_seqid(). nfs_increment_sequid() does not use the
seqid_mutating_err() function fixed in commit 059aa7348241 ("Don't
increment lock sequence ID after NFS4ERR_MOVED").
Fixes: 059aa7348241 ("Don't increment lock sequence ID after ...") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Tested-by: Xuan Qi <xuan.qi@oracle.com> Cc: stable@vger.kernel.org # v3.7+ Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"swiotlb buffer is full" errors occur after repeated initialisation of a
device - f.e. suspend/resume or ip link set up/down. This is because memory
mapped using dma_map_single() in ravb_ring_format() and ravb_start_xmit()
is not released. Resolve this problem by unmapping descriptors when
freeing rings.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[simon: reworked] Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original ast driver will access some BMC configuration through P2A bridge
that can be disabled since AST2300 and after.
It will cause system hanged if P2A bridge is disabled.
Here is the update to fix it.
Commit cae9ff036eea effectively disabled the drm poll_helper by checking
the wrong flag to see if the driver should enable the poll or not:
mode_config.poll_enabled is only set to true by poll_init and it is not
indicating if the poll is enabled or not.
nouveau_display_create() will initialize the poll and going to disable it
right away. After poll_init() the mode_config.poll_enabled will be true,
but the poll itself is disabled.
To avoid the race caused by calling the poll_enable() from different paths,
this patch will enable the poll from one place, in the
nouveau_display_hpd_work().
In case the pm_runtime is disabled we will enable the poll in
nouveau_drm_load() once.
Fixes: cae9ff036eea ("drm/nouveau: Don't enabling polling twice on runtime resume") Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Lyude <lyude@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As it turns out, on cards that actually have CRTCs on them we're already
calling drm_kms_helper_poll_enable(drm_dev) from
nouveau_display_resume() before we call it in
nouveau_pmops_runtime_resume(). This leads us to accidentally trying to
enable polling twice, which results in a potential deadlock between the
RPM locks and drm_dev->mode_config.mutex if we end up trying to enable
polling the second time while output_poll_execute is running and holding
the mode_config lock. As such, make sure we only enable polling in
nouveau_pmops_runtime_resume() if we need to.
This fixes hangs observed on the ThinkPad W541
Signed-off-by: Lyude <lyude@redhat.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Kilian Singer <kilian.singer@quantumtechnology.info> Cc: Lukas Wunner <lukas@wunner.de> Cc: David Airlie <airlied@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resuming from RPM can happen while already holding
dev->mode_config.mutex. This means we can't actually handle fbcon in
any RPM resume workers, since restoring fbcon requires grabbing
dev->mode_config.mutex again. So move the fbcon suspend/resume code into
it's own worker, and rely on that instead to avoid deadlocking.
This fixes more deadlocks for runtime suspending the GPU on the ThinkPad
W541. Reproduction recipe:
- Get a machine with both optimus and a nvidia card with connectors
attached to it
- Wait for the nvidia GPU to suspend
- Attempt to manually reprobe any of the connectors on the nvidia GPU
using sysfs
- *deadlock*
[airlied: use READ_ONCE to address Hans's comment]
Signed-off-by: Lyude <lyude@redhat.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Kilian Singer <kilian.singer@quantumtechnology.info> Cc: Lukas Wunner <lukas@wunner.de> Cc: David Airlie <airlied@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to call drm_helper_hpd_irq_event() on resume to properly detect
monitor connection / disconnection on some laptops. For runtime-resume
(which gets called on resume from normal suspend too) we must call
drm_helper_hpd_irq_event() from a workqueue to avoid a deadlock.
Rename acpi_work to hpd_work, and move it out of the #ifdef CONFIG_ACPI
blocks to make it suitable for generic work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Various notebooks with nvidia GPUs generate an ACPI_VIDEO_NOTIFY_PROBE
acpi-video event when an external device gets plugged in (and again on
modesets on that connector), the default behavior in the acpi-video
driver for this is to send a KEY_SWITCHVIDEOMODE evdev event, which
causes e.g. gnome-settings-daemon to ask us to rescan the connectors
(good), but also causes g-s-d to switch to mirror mode on a newly plugged
monitor rather then using the monitor to extend the desktop (bad)
as KEY_SWITCHVIDEOMODE is supposed to switch between extend the desktop
vs mirror mode.
More troublesome are the repeated ACPI_VIDEO_NOTIFY_PROBE events on
changing the mode on the connector, which cause g-s-d to switch
between mirror/extend mode, which causes a new ACPI_VIDEO_NOTIFY_PROBE
event and we end up with an endless loop.
This commit fixes this by adding an acpi notifier block handler to
nouveau_display.c to intercept ACPI_VIDEO_NOTIFY_PROBE and:
1) Wake-up runtime suspended GPUs and call drm_helper_hpd_irq_event()
on them, this is necessary in some cases for the GPU to detect connector
hotplug events while runtime suspended
2) Return NOTIFY_BAD to stop acpi-video from emitting a bogus
KEY_SWITCHVIDEOMODE key-press event
There already is another acpi notifier block handler registered in
drivers/gpu/drm/nouveau/nvkm/engine/device/acpi.c, but that is not
suitable since that one gets unregistered on runtime suspend, and
we also want to intercept ACPI_VIDEO_NOTIFY_PROBE when runtime suspended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Auto-load the module when userspace asks for the gtp netlink
family.
Signed-off-by: Andreas Schultz <aschultz@tpip.net> Acked-by: Harald Welte <laforge@netfilter.org> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is adds support for the PHYs in the KSZ8795 5port managed switch.
It will allow to detect the link between the switch and the soc
and uses the same read_status functions as the KSZ8873MLL switch.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we fail to retrieve a hardware steering name-space, the returned error
code should say that this operation is not supported. Align the various
places in the driver where this call is made to this convention.
Also, make sure to warn when we fail to retrieve a SW (ANCHOR) name-space.
Make sure to return error when we failed retrieving the FDB steering
name space. Also, while around, correctly print the error when mode
change revert fails in the warning message.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reported-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've seen this trigger twice now, where the i915_gem_object_to_ggtt()
call in intel_unpin_fb_obj() returns NULL, resulting in an oops
immediately afterwards as the (inlined) call to i915_vma_unpin_fence()
tries to dereference it.
It seems to be some race condition where the object is going away at
shutdown time, since both times happened when shutting down the X
server. The call chains were different:
and this patch purely papers over the issue by adding a NULL pointer
check and a WARN_ON_ONCE() to avoid the oops that would then generally
make the machine unresponsive.
Other callers of i915_gem_object_to_ggtt() seem to also check for the
returned pointer being NULL and warn about it, so this clearly has
happened before in other places.
[ Reported it originally to the i915 developers on Jan 8, applying the
ugly workaround on my own now after triggering the problem for the
second time with no feedback.
I was under the misconception that the sysfs dev stuff can be fully
set up, and then registered all in one step with device_add. That's
true for properties and property groups, but not for parents and child
devices. Those must be fully registered before you can register a
child.
Add a bit of tracking to make sure that asynchronous mst connector
hotplugging gets this right. For consistency we rely upon the implicit
barriers of the connector->mutex, which is taken anyway, to ensure
that at least either the connector or device registration call will
work out.
Mildly tested since I can't reliably reproduce this on my mst box
here.
Reported-by: Dave Hansen <dave.hansen@intel.com> Cc: Dave Hansen <dave.hansen@intel.com> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1484237756-2720-1-git-send-email-daniel.vetter@ffwll.ch Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we're unlucky then the registration from a hotplugged connector
might race with the final registration step on driver load. And since
MST topology discover is asynchronous that's even somewhat likely.
v2: Also update the kerneldoc for @registered!
v3: Review from Chris:
- Improve kerneldoc for late_register/early_unregister callbacks.
- Use mutex_destroy.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Sean Paul <seanpaul@chromium.org> Reported-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20161218133545.2106-1-daniel.vetter@ffwll.ch Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 04ff5a095d66 ("pinctrl: baytrail: Rectify debounce support")
almost fixes the logic of debuonce but missed couple of things, i.e.
typo in mask when disabling debounce and lack of enabling it back.
This patch addresses above issues.
Reported-by: Jean Delvare <jdelvare@suse.de> Fixes: 04ff5a095d66 ("pinctrl: baytrail: Rectify debounce support") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In spite of switching to paged allocation of Rx buffers, the driver still
called dma_unmap_single() in the Rx queues tear-down path.
The DMA region unmapping code in free_skb_rx_queue() basically predates
the introduction of paged allocation to the driver. While being refactored,
it apparently hasn't reflected the change in the DMA API usage by its
counterpart gfar_new_page().
As a result, setting an interface to the DOWN state now yields the following:
# ip link set eth2 down
fsl-gianfar ffe24000.ethernet: DMA-API: device driver frees DMA memory with wrong function [device address=0x000000001ecd0000] [size=40]
------------[ cut here ]------------
WARNING: CPU: 1 PID: 189 at lib/dma-debug.c:1123 check_unmap+0x8e0/0xa28
CPU: 1 PID: 189 Comm: ip Tainted: G O 4.9.5 #1
task: dee73400 task.stack: dede2000
NIP: c02101e8 LR: c02101e8 CTR: c0260d74
REGS: dede3bb0 TRAP: 0700 Tainted: G O (4.9.5)
MSR: 00021000 <CE,ME> CR: 28002222 XER: 00000000
Some Hypervisors detach VFs from VMs by instantly causing an FLR event
to be generated for a VF.
In the mlx4 case, this will cause that VF's comm channel to be disabled
before the VM has an opportunity to invoke the VF device's "shutdown"
method.
The result is that the VF driver on the VM will experience a command
timeout during the shutdown process when the Hypervisor does not deliver
a command-completion event to the VM.
To avoid FW command timeouts on the VM when the driver's shutdown method
is invoked, we detect the absence of the VF's comm channel at the very
start of the shutdown process. If the comm-channel has already been
disabled, we cause all FW commands during the device shutdown process to
immediately return success (and thus avoid all command timeouts).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ip6_make_flowlabel() determines the flow label for IPv6 packets. It's
supposed to be passed a flow label, which it returns as is if non-0 and
in some other cases, otherwise it calculates a new value.
The problem is callers often pass a flowi6.flowlabel, which may also
contain traffic class bits. If the traffic class is non-0
ip6_make_flowlabel() mistakes the non-0 it gets as a flow label and
returns the whole thing. Thus it can return a 'flow label' longer than
20b and the low 20b of that is typically 0 resulting in packets with 0
label. Moreover, different packets of a flow may be labeled differently.
For a TCP flow with ECN non-payload and payload packets get different
labels as exemplified by this pair of consecutive packets:
This patch allows ip6_make_flowlabel() to be passed more than just a
flow label and has it extract the part it really wants. This was simpler
than modifying the callers. With this patch packets like the above become
Initialise the stores_lock in fscache netfs cookies. Technically, it
shouldn't be necessary, since the netfs cookie is an index and stores no
data, but initialising it anyway adds insignificant overhead.
Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Acked-by: Steve Dickson <steved@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fscache_disable_cookie() needs to clear the outstanding writes on the
cookie it's disabling because they cannot be completed after.
Without this, fscache_nfs_open_file() gets stuck because it disables the
cookie when the file is opened for writing but can't uncache the pages till
afterwards - otherwise there's a race between the open routine and anyone
who already has it open R/O and is still reading from it.
Looking in /proc/pid/stack of the offending process shows:
Under some circumstances, an fscache object can become queued such that it
fscache_object_work_func() can be called once the object is in the
OBJECT_DEAD state. This results in the kernel oopsing when it tries to
invoke the handler for the state (which is hard coded to 0x2).
The way this comes about is something like the following:
(1) The object dispatcher is processing a work state for an object. This
is done in workqueue context.
(2) An out-of-band event comes in that isn't masked, causing the object to
be queued, say EV_KILL.
(3) The object dispatcher finishes processing the current work state on
that object and then sees there's another event to process, so,
without returning to the workqueue core, it processes that event too.
It then follows the chain of events that initiates until we reach
OBJECT_DEAD without going through a wait state (such as
WAIT_FOR_CLEARANCE).
At this point, object->events may be 0, object->event_mask will be 0
and oob_event_mask will be 0.
(4) The object dispatcher returns to the workqueue processor, and in due
course, this sees that the object's work item is still queued and
invokes it again.
(5) The current state is a work state (OBJECT_DEAD), so the dispatcher
jumps to it - resulting in an OOPS.
When I'm seeing this, the work state in (1) appears to have been either
LOOK_UP_OBJECT or CREATE_OBJECT (object->oob_table is
fscache_osm_lookup_oob).
The window for (2) is very small:
(A) object->event_mask is cleared whilst the event dispatch process is
underway - though there's no memory barrier to force this to the top
of the function.
The window, therefore is from the time the object was selected by the
workqueue processor and made requeueable to the time the mask was
cleared.
(B) fscache_raise_event() will only queue the object if it manages to set
the event bit and the corresponding event_mask bit was set.
The enqueuement is then deferred slightly whilst we get a ref on the
object and get the per-CPU variable for workqueue congestion. This
slight deferral slightly increases the probability by allowing extra
time for the workqueue to make the item requeueable.
Handle this by giving the dead state a processor function and checking the
for the dead state address rather than seeing if the processor function is
address 0x2. The dead state processor function can then set a flag to
indicate that it's occurred and give a warning if it occurs more than once
per object.
If this race occurs, an oops similar to the following is seen (note the RIP
value):
projects / linux / log