If sclp_init() fails it only partially cleans up: if there are multiple
failing calls to sclp_init() sclp_state_change_event will be added several
times to sclp_reg_list, which results in the following warning:
Fill this in so user-space can identify multiple ports on the same CP
unit.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the driver supports more devices over time the single MODULE_ALIAS
is complete and raises several warnings:
SPI driver ads7846 has no spi_device_id for ti,tsc2046
SPI driver ads7846 has no spi_device_id for ti,ads7843
SPI driver ads7846 has no spi_device_id for ti,ads7845
SPI driver ads7846 has no spi_device_id for ti,ads7873
Fix this by adding a spi_device_id table and removing the manual
MODULE_ALIAS.
If the ASP1 DAI is hooked up by the machine driver the ASP TX mixer
sources should be initialized to disconnected. There aren't currently
any available products using the ASP so this doesn't affect any
existing systems.
The cs35l56 does not have any fixed default for the mixer source
registers. When the cs35l56 boots, its firmware patches these registers
to setup a system-specific routing; this is so that Windows can use
generic SDCA drivers instead of needing knowledge of chip-specific
registers. The setup varies between end-products, which each have
customized firmware, and so the default register state varies between
end-products. It can also change if the firmware on an end-product is
upgraded - for example if a change was needed to the routing for Windows
use-cases. It must be emphasized that the settings applied by the
firmware are not internal magic tuning; they are statically implementing
use-case setup that on Linux would be done via ALSA controls.
The driver is currently syncing the mixer controls with whatever
initial state the firmware wrote to the registers, so that they report
the actual audio routing. But if the ASP DAI is hooked up this can create
a powered-up DAPM graph without anything intentionally setting up a path.
This can lead to parts of the audio system powering up unexpectedly.
For example when cs35l56 is connected to cs42l43 using a codec-codec link,
this can create a complete DAPM graph which then powers-up cs42l43. But
the cs42l43 can only be clocked from its SoundWire bus so this causes a
bunch of errors in the kernel log where cs42l43 is unexpectedly powered-up
without a clock.
If the host is taking ownership of the ASP (either directly or as a
codec-to-codec link) there is no need to keep the mixer settings that the
firmware wrote. The driver has ALSA controls for setting these using
standard Linux mechanisms. So if the machine driver hooks up the ASP the
ASP mixers are initialized to "None" (no input). This prevents unintended
DAPM-graph power-ups, and means the initial state of the mixers is
always going to be None.
Since the initial state of the mixers can vary from system to system and
potentially between firmware upgrades, no use-case manager can currently
assume that cs35l56 has a known initial state. The firmware could just as
easily default them to "None" as to any input source. So defaulting them
to "None" in the driver is not increasing the entropy of the system.
The minimum period size was enforced to 64 as older devices integrating
McASP with EDMA used an internal FIFO of 64 samples.
With UDMA based platforms this internal McASP FIFO is optional, as the
DMA engine internally does some buffering which is already accounted for
when registering the platform. So we should read the actual FIFO
configuration (txnumevt/rxnumevt) instead of hardcoding frames.min to
64.
Sometimes the stream may be stopped due to XRUN events, in which case
the userspace can call snd_pcm_drop() and snd_pcm_prepare() to stop and
start the stream again.
In these cases, we must wait for the DMA channel to synchronize before
marking the stream as prepared for playback, as the DMA channel gets
stopped by drop() without any synchronization. Make sure the ALSA core
synchronizes the DMA channel by adding a sync_stop() hook.
When headphones are plugged in, they appear absent; when they are removed,
they appear present.
Add a specific entry in bytcr_rt5640 for this device
Signed-off-by: Thomas GENTY <tomlohave@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20240608170251.99936-1-tomlohave@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Most users after parsing a topology file, release memory used by it, so
having pointer references directly into topology file contents is wrong.
Use devm_kmemdup(), to allocate memory as needed.
The Lenovo N24 on resume becomes stuck in a state where it
sends incorrect packets, causing elantech_packet_check_v4 to fail.
The only way for the device to resume sending the correct packets is for
it to be disabled and then re-enabled.
This change adds a dmi check to trigger this behavior on resume.
Currently, worker ID formatting is open coded in create_worker(),
init_rescuer() and worker_thread() (for %WORKER_DIE case). The formatted ID
is saved into task->comm and wq_worker_comm() uses it as the base name to
append extra information to when generating the name to be shown to
userspace.
However, TASK_COMM_LEN is only 16 leading to badly truncated names for
rescuers. For example, the rescuer for the inet_frag_wq workqueue becomes:
Even for non-rescue workers, it's easy to run over 15 characters on
moderately large machines.
Fit it by consolidating worker ID formatting into a new helper
format_worker_id() and calling it from wq_worker_comm() to obtain the
untruncated worker ID string.
This is almost compatible, but passing a negative offset should result
in a EINVAL error, but on mips o32 compat mode would seek to a large
32-bit byte offset.
Use compat_sys_lseek() to correctly sign-extend the argument.
The ACPI IDs used in the CS35L56 HDA drivers are all handled by the
serial multi-instantiate driver which starts multiple Linux device
instances from a single ACPI Device() node.
As serial multi-instantiate is not an optional part of the system add it
as a dependency in Kconfig so that it is not overlooked.
[Why & How]
Current DRAM setting would cause underflow on customer platform.
Modify dram_clock_change_latency_us from 11.72 to 34.0 us as per recommendation from HW team
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com> Signed-off-by: Paul Hsieh <paul.hsieh@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Netlink flags, although they don't have payload at the netlink level,
are represented as having "True" as value in pyroute2.
Without it, trying to add a flow with a flag-type action (e.g: pop_vlan)
fails with the following traceback:
Traceback (most recent call last):
File "[...]/ovs-dpctl.py", line 2498, in <module>
sys.exit(main(sys.argv))
^^^^^^^^^^^^^^
File "[...]/ovs-dpctl.py", line 2487, in main
ovsflow.add_flow(rep["dpifindex"], flow)
File "[...]/ovs-dpctl.py", line 2136, in add_flow
reply = self.nlm_request(
^^^^^^^^^^^^^^^^^
File "[...]/pyroute2/netlink/nlsocket.py", line 822, in nlm_request
return tuple(self._genlm_request(*argv, **kwarg))
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
File "[...]/pyroute2/netlink/generic/__init__.py", line 126, in
nlm_request
return tuple(super().nlm_request(*argv, **kwarg))
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
File "[...]/pyroute2/netlink/nlsocket.py", line 1124, in nlm_request
self.put(msg, msg_type, msg_flags, msg_seq=msg_seq)
File "[...]/pyroute2/netlink/nlsocket.py", line 389, in put
self.sendto_gate(msg, addr)
File "[...]/pyroute2/netlink/nlsocket.py", line 1056, in sendto_gate
msg.encode()
File "[...]/pyroute2/netlink/__init__.py", line 1245, in encode
offset = self.encode_nlas(offset)
^^^^^^^^^^^^^^^^^^^^^^^^
File "[...]/pyroute2/netlink/__init__.py", line 1560, in encode_nlas
nla_instance.setvalue(cell[1])
File "[...]/pyroute2/netlink/__init__.py", line 1265, in setvalue
nlv.setvalue(nla_tuple[1])
~~~~~~~~~^^^
IndexError: list index out of range
Signed-off-by: Adrian Moreno <amorenoz@redhat.com> Acked-by: Aaron Conole <aconole@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Hardcoding the number of CPUs at compile time does improve code
generation, but if you get it wrong the result will be confusion.
We already limited this earlier to only "experts" (see commit fe5759d5bfda "cpumask: limit visibility of FORCE_NR_CPUS"), but with
distro kernel configs often having EXPERT enabled, that turns out to not
be much of a limit.
To quote the philosophers at Disney: "Everyone can be an expert. And
when everyone's an expert, no one will be".
There's a runtime warning if you then set nr_cpus to anything but the
forced number, but apparently that can be ignored too [1] and by then
it's pretty much too late anyway.
If we had some real way to limit this to "embedded only", maybe it would
be worth it, but let's see if anybody even notices that the option is
gone. We need to simplify kernel configuration anyway.
Link: https://lore.kernel.org/all/20240618105036.208a8860@rorschach.local.home/ Reported-by: Steven Rostedt <rostedt@goodmis.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Paul McKenney <paulmck@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Yury Norov <yury.norov@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Al reported a possible use-after-free (UAF) in kvm_spapr_tce_attach_iommu_group().
It looks up `stt` from tablefd, but then continues to use it after doing
fdput() on the returned fd. After the fdput() the tablefd is free to be
closed by another thread. The close calls kvm_spapr_tce_release() and
then release_spapr_tce_table() (via call_rcu()) which frees `stt`.
Although there are calls to rcu_read_lock() in
kvm_spapr_tce_attach_iommu_group() they are not sufficient to prevent
the UAF, because `stt` is used outside the locked regions.
With an artifcial delay after the fdput() and a userspace program which
triggers the race, KASAN detects the UAF:
Fix it by delaying the fdput() until `stt` is no longer in use, which
is effectively the entire function. To keep the patch minimal add a call
to fdput() at each of the existing return paths. Future work can convert
the function to goto or __cleanup style cleanup.
With the fix in place the test case no longer triggers the UAF.
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Closes: https://lore.kernel.org/all/20240610024437.GA1464458@ZenIV/ Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20240614122910.3499489-1-mpe@ellerman.id.au Signed-off-by: Sasha Levin <sashal@kernel.org>
Add support for this laptop, which uses CS35L41 HDA amps.
The laptop does not contain valid _DSD for these amps, so requires
entries into the CS35L41 configuration table to function correctly.
Add support for this laptop, which uses CS35L41 HDA amps.
The laptop does not contain valid _DSD for these amps, so requires
entries into the CS35L41 configuration table to function correctly.
[ fixed to lower hex numbers in quirk entries -- tiwai ]
In 'cfg80211_wext_siwscan()', add extra check whether number of
channels passed via 'ioctl(sock, SIOCSIWSCAN, ...)' doesn't exceed
IW_MAX_FREQUENCIES and reject invalid request with -EINVAL otherwise.
The codec should be cleared when the amp driver is unbound and when
resuming it should be tested to prevent loading firmware into the device
and ALSA in a partially configured system state.
If fallcate is implemented but zero and discard operations are not
supported by the filesystem the backing file is on we continue to fill
dmesg with errors from the blk_mq_end_request() since each time we call
fallocate() on the loop device the EOPNOTSUPP error from lo_fallocate()
ends up propagated into the block layer. In the end syscall succeeds
since the blkdev_issue_zeroout() falls back to writing zeroes which
makes the errors even more misleading and confusing.
How to reproduce:
1. make sure /tmp is mounted as tmpfs
2. dd if=/dev/zero of=/tmp/disk.img bs=1M count=100
3. losetup /dev/loop0 /tmp/disk.img
4. mkfs.ext2 /dev/loop0
5. dmesg |tail
[710690.898214] operation not supported error, dev loop0, sector 204672 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.898279] operation not supported error, dev loop0, sector 522 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.898603] operation not supported error, dev loop0, sector 16906 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.898917] operation not supported error, dev loop0, sector 32774 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.899218] operation not supported error, dev loop0, sector 49674 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.899484] operation not supported error, dev loop0, sector 65542 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.899743] operation not supported error, dev loop0, sector 82442 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.900015] operation not supported error, dev loop0, sector 98310 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.900276] operation not supported error, dev loop0, sector 115210 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.900546] operation not supported error, dev loop0, sector 131078 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
This patch changes the lo_fallocate() to clear the flags for zero and
discard operations if we get EOPNOTSUPP from the backing file fallocate
callback, that way we at least stop spewing errors after the first
unsuccessful try.
CC: Jan Kara <jack@suse.cz> Signed-off-by: Cyril Hrubis <chrubis@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20240613163817.22640-1-chrubis@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to improve performance of typical scenarios we can try to insert
the entire vma on fault. This accelerates typical cases, such as when
the MMIO region is DMA mapped by QEMU. The vfio_iommu_type1 driver will
fault in the entire DMA mapped range through fixup_user_fault().
In synthetic testing, this improves the time required to walk a PCI BAR
mapping from userspace by roughly 1/3rd.
This is likely an interim solution until vmf_insert_pfn_{pmd,pud}() gain
support for pfnmaps.
The spec doesn't mandate that the first two double words (aka results)
for the command queue entry need to be set to 0 when they are not
used (not specified). Though, the target implemention returns 0 for TCP
and FC but not for RDMA.
Let's make RDMA behave the same and thus explicitly initializing the
result field. This prevents leaking any data from the stack.
Signed-off-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a discard request needs to be retried, and that retry may fail before
a new special payload is added, a double free will result. Clear the
RQF_SPECIAL_LOAD when the request is cleaned.
Signed-off-by: Chunguang Xu <chunguang.xu@shopee.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Based on grepping through the source code this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown
time. Among other things, this means that if a panel is in use that it
won't be cleanly powered off at system shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart comes straight out of the kernel doc "driver
instance overview" in drm_drv.c.
This driver users the component model and shutdown happens in the base
driver. The "drvdata" for this driver will always be valid if
shutdown() is called and as of commit 2a073968289d
("drm/atomic-helper: drm_atomic_helper_shutdown(NULL) should be a
noop") we don't need to confirm that "drm" is non-NULL.
Based on grepping through the source code, this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown time.
This is important because drm_atomic_helper_shutdown() will cause
panels to get disabled cleanly which may be important for their power
sequencing. Future changes will remove any custom powering off in
individual panel drivers so the DRM drivers need to start getting this
right.
The fact that we should call drm_atomic_helper_shutdown() in the case of
OS shutdown comes straight out of the kernel doc "driver instance
overview" in drm_drv.c.
Core in platform_driver_register() already sets the .owner, so driver
does not need to. Whatever is set here will be anyway overwritten by
main driver calling platform_driver_register().
If the extent spans the block that contains i_size, we need to handle
both halves separately so that we properly zero data in the page cache
for blocks that are entirely outside of i_size. But this is needed only
when i_size is within the current folio under processing.
"orig_pos + length > isize" can be true for all folios if the mapped
extent length is greater than the folio size. That is making plen to
break for every folio instead of only the last folio.
So use orig_plen for checking if "orig_pos + orig_plen > isize".
Signed-off-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com> Link: https://lore.kernel.org/r/a32e5f9a4fcfdb99077300c4020ed7ae61d6e0f9.1715067055.git.ritesh.list@gmail.com Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Jan Kara <jack@suse.cz>
cc: Ojaswin Mujoo <ojaswin@linux.ibm.com> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As described in the added code comment, a reference to .exit.text is ok
for drivers registered via module_platform_driver_probe(). Make this
explicit to prevent the following section mismatch warning
Change level for the "not connected" client message in the write
callback from error to debug.
The MEI driver currently disconnects all clients upon system suspend.
This behavior is by design and user-space applications with
open connections before the suspend are expected to handle errors upon
resume, by reopening their handles, reconnecting,
and retrying their operations.
However, the current driver implementation logs an error message every
time a write operation is attempted on a disconnected client.
Since this is a normal and expected flow after system resume
logging this as an error can be misleading.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Link: https://lore.kernel.org/r/20240530091415.725247-1-tomas.winkler@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the vfio device fd tied to the address space of the pseudo fs
inode, we can use the mm to track all vmas that might be mmap'ing
device BARs, which removes our vma_list and all the complicated lock
ordering necessary to manually zap each related vma.
Note that we can no longer store the pfn in vm_pgoff if we want to use
unmap_mapping_range() to zap a selective portion of the device fd
corresponding to BAR mappings.
This also converts our mmap fault handler to use vmf_insert_pfn()
because we no longer have a vma_list to avoid the concurrency problem
with io_remap_pfn_range(). The goal is to eventually use the vm_ops
huge_fault handler to avoid the additional faulting overhead, but
vmf_insert_pfn_{pmd,pud}() need to learn about pfnmaps first.
Also, Jason notes that a race exists between unmap_mapping_range() and
the fops mmap callback if we were to call io_remap_pfn_range() to
populate the vma on mmap. Specifically, mmap_region() does call_mmap()
before it does vma_link_file() which gives a window where the vma is
populated but invisible to unmap_mapping_range().
Suggested-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Link: https://lore.kernel.org/r/20240530045236.1005864-3-alex.williamson@redhat.com Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
By linking all the device fds we provide to userspace to an
address space through a new pseudo fs, we can use tools like
unmap_mapping_range() to zap all vmas associated with a device.
Suggested-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Link: https://lore.kernel.org/r/20240530045236.1005864-2-alex.williamson@redhat.com Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The maximum possible return value of find_next_zero_bit(fdt->full_fds_bits,
maxbit, bitbit) is maxbit. This return value, multiplied by BITS_PER_LONG,
gives the value of bitbit, which can never be greater than maxfd, it can
only be equal to maxfd at most, so the following check 'if (bitbit > maxfd)'
will never be true.
Moreover, when bitbit equals maxfd, it indicates that there are no unused
fds, and the function can directly return.
Replacing wait_for_completion() with wait_for_completion_killable() in
cachefiles_ondemand_send_req() allows us to kill processes that might
trigger a hunk_task if the daemon is abnormal.
But now only CACHEFILES_OP_READ is killable, because OP_CLOSE and OP_OPEN
is initiated from kworker context and the signal is prohibited in these
kworker.
Note that when the req in xas changes, i.e. xas_load(&xas) != req, it
means that a process will complete the current request soon, so wait
again for the request to be completed.
In addition, add the cachefiles_ondemand_finish_req() helper function to
simplify the code.
Suggested-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Baokun Li <libaokun1@huawei.com> Link: https://lore.kernel.org/r/20240522114308.2402121-13-libaokun@huaweicloud.com Acked-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Jia Zhu <zhujia.zj@bytedance.com> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If copen is maliciously called in the user mode, it may delete the request
corresponding to the random id. And the request may have not been read yet.
Note that when the object is set to reopen, the open request will be done
with the still reopen state in above case. As a result, the request
corresponding to this object is always skipped in select_req function, so
the read request is never completed and blocks other process.
Fix this issue by simply set object to close if its id < 0 in copen.
Signed-off-by: Zizhi Wo <wozizhi@huawei.com> Signed-off-by: Baokun Li <libaokun1@huawei.com> Link: https://lore.kernel.org/r/20240522114308.2402121-11-libaokun@huaweicloud.com Acked-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Jia Zhu <zhujia.zj@bytedance.com> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This prevents malicious processes from completing random copen/cread
requests and crashing the system. Added checks are listed below:
* Generic, copen can only complete open requests, and cread can only
complete read requests.
* For copen, ondemand_id must not be 0, because this indicates that the
request has not been read by the daemon.
* For cread, the object corresponding to fd and req should be the same.
Signed-off-by: Baokun Li <libaokun1@huawei.com> Link: https://lore.kernel.org/r/20240522114308.2402121-7-libaokun@huaweicloud.com Acked-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a slight variation on a patch previously proposed by Neil Brown
that never got merged.
Prior to commit 5ceb9d7fdaaf ("NFS: Refactor nfs_lookup_revalidate()"),
any error from nfs_lookup_verify_inode() other than -ESTALE would result
in nfs_lookup_revalidate() returning that error (-ESTALE is mapped to
zero).
Since that commit, all errors result in nfs_lookup_revalidate()
returning zero, resulting in dentries being invalidated where they
previously were not (particularly in the case of -ERESTARTSYS).
Fix it by passing the actual error code to nfs_lookup_revalidate_done(),
and leaving the decision on whether to map the error code to zero or
one to nfs_lookup_revalidate_done().
A simple reproducer is to run the following python code in a
subdirectory of an NFS mount (not in the root of the NFS mount):
---8<---
import os
import multiprocessing
import time
if __name__=="__main__":
multiprocessing.set_start_method("spawn")
count = 0
while True:
try:
os.getcwd()
pool = multiprocessing.Pool(10)
pool.close()
pool.terminate()
count += 1
except Exception as e:
print(f"Failed after {count} iterations")
print(e)
break
---8<---
Prior to commit 5ceb9d7fdaaf, the above code would run indefinitely.
After commit 5ceb9d7fdaaf, it fails almost immediately with -ENOENT.
When we are doing WB_SYNC_ALL writeback, nfs submits write requests with
NFS_FILE_SYNC flag to the server (which then generally treats it as an
O_SYNC write). This helps to reduce latency for single requests but when
submitting more requests, additional fsyncs on the server side hurt
latency. NFS generally avoids this additional overhead by not setting
NFS_FILE_SYNC if desc->pg_moreio is set.
However this logic doesn't always work. When we do random 4k writes to a huge
file and then call fsync(2), each page writeback is going to be sent with
NFS_FILE_SYNC because after preparing one page for writeback, we start writing
back next, nfs_do_writepage() will call nfs_pageio_cond_complete() which finds
the page is not contiguous with previously prepared IO and submits is *without*
setting desc->pg_moreio. Hence NFS_FILE_SYNC is used resulting in poor
performance.
Fix the problem by setting desc->pg_moreio in nfs_pageio_cond_complete() before
submitting outstanding IO. This improves throughput of
fsync-after-random-writes on my test SSD from ~70MB/s to ~250MB/s.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is an inherent race where a symlink file may have been overriden
(by a different client) between lookup and readlink, resulting in a
spurious EIO error returned to userspace. Fix this by propagating back
ESTALE errors such that the vfs will retry the lookup/get_link (similar
to nfs4_file_open) at least once.
Cc: Dan Aloni <dan.aloni@vastdata.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
HUTRR94 added support for a new usage titled "System Do Not Disturb"
which toggles a system-wide Do Not Disturb setting. This commit simply
adds a new event code for the usage.
HUTRR116 added support for a new usage titled "System Accessibility
Binding" which toggles a system-wide bound accessibility UI or command.
This commit simply adds a new event code for the usage.
expr_trans_bool() performs an incorrect transformation.
[Test Code]
config MODULES
def_bool y
modules
config A
def_bool y
select C if B != n
config B
def_tristate m
config C
tristate
[Result]
CONFIG_MODULES=y
CONFIG_A=y
CONFIG_B=m
CONFIG_C=m
This output is incorrect because CONFIG_C=y is expected.
Documentation/kbuild/kconfig-language.rst clearly explains the function
of the '!=' operator:
If the values of both symbols are equal, it returns 'n',
otherwise 'y'.
Therefore, the statement:
select C if B != n
should be equivalent to:
select C if y
Or, more simply:
select C
Hence, the symbol C should be selected by the value of A, which is 'y'.
However, expr_trans_bool() wrongly transforms it to:
select C if B
Therefore, the symbol C is selected by (A && B), which is 'm'.
The comment block of expr_trans_bool() correctly explains its intention:
* bool FOO!=n => FOO
^^^^
If FOO is bool, FOO!=n can be simplified into FOO. This is correct.
However, the actual code performs this transformation when FOO is
tristate:
if (e->left.sym->type == S_TRISTATE) {
^^^^^^^^^^
While it can be fixed to S_BOOLEAN, there is no point in doing so
because expr_tranform() already transforms FOO!=n to FOO when FOO is
bool. (see the "case E_UNEQUAL" part)
The function run_all_insn_set_hw_mode() is registered as startup callback
of 'CPUHP_AP_ARM64_ISNDEP_STARTING', it invokes set_hw_mode() methods of
all emulated instructions.
As the STARTING callbacks are not expected to fail, if one of the
set_hw_mode() fails, e.g. due to el0 mixed-endian is not supported for
'setend', it will report a warning:
```
CPU[2] cannot support the emulation of setend
CPU 2 UP state arm64/isndep:starting (136) failed (-22)
CPU2: Booted secondary processor 0x0000000002 [0x414fd0c1]
```
To fix it, add a check for INSN_UNAVAILABLE status and skip the process.
The io_register_iowq_max_workers() function calls io_put_sq_data(),
which acquires the sqd->lock without releasing the uring_lock.
Similar to the commit 009ad9f0c6ee ("io_uring: drop ctx->uring_lock
before acquiring sqd->lock"), this can lead to a potential deadlock
situation.
To resolve this issue, the uring_lock is released before calling
io_put_sq_data(), and then it is re-acquired after the function call.
This change ensures that the locks are acquired in the correct
order, preventing the possibility of a deadlock.
As explained in commit 1378817486d6 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
Disabling preemption in rpl_output() is not good enough,
because rpl_output() is called from process context,
lwtunnel_output() only uses rcu_read_lock().
We might be interrupted by a softirq, re-enter rpl_output()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable() instead of
preempt_disable().
Apply a similar change in rpl_input().
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Alexander Aring <aahringo@redhat.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/20240531132636.2637995-3-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
HSMP interface is supported only on few x86 processors from AMD.
Accessing HSMP registers on rest of the platforms might cause
unexpected behaviour. So add a check.
Also unavailability of this interface on rest of the processors
is not an error. Hence, use pr_info() instead of the pr_err() to
log the message.
Signed-off-by: Suma Hegde <suma.hegde@amd.com> Reviewed-by: Naveen Krishna Chatradhi <naveenkrishna.chatradhi@amd.com> Link: https://lore.kernel.org/r/20240603081512.142909-1-suma.hegde@amd.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When support for Silead touchscreens was orginal added some touchscreens
with older firmware versions only supported 5 fingers and this was made
the default requiring the setting of a "silead,max-fingers=10" uint32
device-property for all touchscreen models which do support 10 fingers.
There are very few models with the old 5 finger fw, so in practice the
setting of the "silead,max-fingers=10" is boilerplate which needs to
be copy and pasted to every touchscreen config.
Reporting that 10 fingers are supported on devices which only support
5 fingers doesn't cause any problems for userspace in practice, since
at max 4 finger gestures are supported anyways. Drop the max_fingers
configuration and simply always assume 10 fingers.
The GMAC of Loongson chips cannot insert the correct 1.5-2ns delay. So
we need the PHY to insert internal delays for both transmit and receive
data lines from/to the PHY device. Fix this by changing the "phy-mode"
from "rgmii" to "rgmii-id" in dts.
In some scenarios, if too many commands are issued by nvme command in
the same time by user tasks, this may exhaust all tags of admin_q. If
a reset (nvme reset or IO timeout) occurs before these commands finish,
reconnect routine may fail to update nvme regs due to insufficient tags,
which will cause kernel hang forever. In order to workaround this issue,
maybe we can let reg_read32()/reg_read64()/reg_write32() use reserved
tags. This maybe safe for nvmf:
1. For the disable ctrl path, we will not issue connect command
2. For the enable ctrl / fw activate path, since connect and reg_xx()
are called serially.
So the reserved tags may still be enough while reg_xx() use reserved tags.
Factor out the parsing of interrupt-map interrupt parent phandle and its
arg cells to a separate function, of_irq_parse_imap_parent(), so that it
can be used in other parsing scenarios (e.g. fw_devlink).
There was a refcount leak on non-matching entries when iterating thru
"interrupt-map" which is fixed.
Fix build error on ppc64:
dev_in_maps.c: In function ‘get_file_dev_and_inode’:
dev_in_maps.c:60:59: error: format ‘%llu’ expects argument of type
‘long long unsigned int *’, but argument 7 has type ‘__u64 *’ {aka ‘long
unsigned int *’} [-Werror=format=]
By switching to unsigned long long for u64 for ppc64 builds.
openat2_test.c: In function ‘test_openat2_flags’:
openat2_test.c:303:73: warning: format ‘%llX’ expects argument of type
‘long long unsigned int’, but argument 5 has type ‘__u64’ {aka ‘long
unsigned int’} [-Wformat=]
By switching to unsigned long long for u64 for ppc64 builds.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix warnings like:
test_cachestat.c: In function ‘print_cachestat’:
test_cachestat.c:30:38: warning: format ‘%llu’ expects argument of
type ‘long long unsigned int’, but argument 2 has type ‘__u64’ {aka
‘long unsigned int’} [-Wformat=]
By switching to unsigned long long for u64 for ppc64 builds.
When testing the previous patch with CONFIG_UBSAN_BOUNDS, I've
noticed the following:
UBSAN: array-index-out-of-bounds in net/mac80211/scan.c:372:4
index 0 is out of range for type 'struct ieee80211_channel *[]'
CPU: 0 PID: 1435 Comm: wpa_supplicant Not tainted 6.9.0+ #1
Hardware name: LENOVO 20UN005QRT/20UN005QRT <...BIOS details...>
Call Trace:
<TASK>
dump_stack_lvl+0x2d/0x90
__ubsan_handle_out_of_bounds+0xe7/0x140
? timerqueue_add+0x98/0xb0
ieee80211_prep_hw_scan+0x2db/0x480 [mac80211]
? __kmalloc+0xe1/0x470
__ieee80211_start_scan+0x541/0x760 [mac80211]
rdev_scan+0x1f/0xe0 [cfg80211]
nl80211_trigger_scan+0x9b6/0xae0 [cfg80211]
...<the rest is not too useful...>
Since '__ieee80211_start_scan()' leaves 'hw_scan_req->req.n_channels'
uninitialized, actual boundaries of 'hw_scan_req->req.channels' can't
be checked in 'ieee80211_prep_hw_scan()'. Although an initialization
of 'hw_scan_req->req.n_channels' introduces some confusion around
allocated vs. used VLA members, this shouldn't be a problem since
everything is correctly adjusted soon in 'ieee80211_prep_hw_scan()'.
Cleanup 'kmalloc()' math in '__ieee80211_start_scan()' by using the
convenient 'struct_size()' as well.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Link: https://msgid.link/20240517153332.18271-2-dmantipov@yandex.ru
[improve (imho) indentation a bit] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When HW rfkill is toggled to disable the RF, the flow to stop scan is
called. When trying to send the command to abort the scan, since
HW rfkill is toggled, the command is not sent due to rfkill being
asserted, and -ERFKILL is returned from iwl_trans_send_cmd(), but this
is silently ignored in iwl_mvm_send_cmd() and thus the scan abort flow
continues to wait for scan complete notification and fails. Since it
fails, the UID to type mapping is not cleared, and thus a warning is
later fired when trying to stop the interface.
To fix this, modify the UMAC scan abort flow to force sending the
scan abort command even when in rfkill, so stop the FW from accessing
the radio etc.
When entering RF-kill, mac80211 tears down BA sessions, but
due to RF-kill the commands aren't sent to the device. As a
result, there can be frames pending on the reorder buffer or
perhaps even received while doing so, leading to warnings.
Avoid the warnings by doing the BA session teardown normally
even in RF-kill, which also requires queue sync.
The BIGTK cipher field was added to the kek_kck_material_cmd
but wasn't assigned. Fix that by differentiating between the
IGTK/BIGTK keys and assign the ciphers fields accordingly.
If pre-recovery mac80211 tried to disable a link but this disablement
failed, then there might be a mismatch between mac80211 assuming the
link has been disabled and the driver still having the data around.
During recover itself, that is not a problem, but should the link be
activated again at a later point, iwlwifi will refuse the activation as
it detects the inconsistent state.
Solve this corner-case by iterating the station in the restart cleanup
handler.
After moving from commands to notificaitons in the d3 resume flow,
removing the WOWLAN_GET_STATUSES and REPLY_OFFLOADS_QUERY_CMD causes
the return of the default value when looking up their version.
Returning zero here results in the driver sending the not supported
NON_QOS_TX_COUNTER_CMD.
The 6 GHz scan request struct allocated by cfg80211_scan_6ghz() is
meant to be formed this way:
[base struct][channels][ssids][6ghz_params]
It is allocated with [channels] as the maximum number of channels
supported by the driver in the 6 GHz band, since allocation is
before knowing how many there will be.
However, the inner pointers are set incorrectly: initially, the
6 GHz scan parameters pointer is set:
[base struct][channels]
^ scan_6ghz_params
and later the SSID pointer is set to the end of the actually
_used_ channels.
[base struct][channels]
^ ssids
If many APs were to be discovered, and many channels used, and
there were many SSIDs, then the SSIDs could overlap the 6 GHz
parameters.
Additionally, the request->ssids for most of the function points
to the original request still (given the struct copy) but is used
normally, which is confusing.
Clear this up, by actually using the allocated space for 6 GHz
parameters _after_ the SSIDs, and set up the SSIDs initially so
they are used more clearly. Just like in nl80211.c, set them
only if there actually are SSIDs though.
Finally, also copy the elements (ie/ie_len) so they're part of
the same request, not pointing to the old request.
Co-developed-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Reviewed-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Link: https://msgid.link/20240510113738.4190692ef4ee.I0cb19188be17a8abd029805e3373c0a7777c214c@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The code itself doesn't want to handle frames from the driver
if it's already stopped, but if the tasklet was queued before
and runs after the stop, then all bets are off. Flush queues
before actually stopping, RX should be off at this point since
all the interfaces are removed already, etc.
With a ath9k device I can see that:
iw phy phy0 interface add mesh0 type mp
ip link set mesh0 up
iw dev mesh0 scan
Will start a scan with the Power Management bit set in the Frame Control Field.
This is because we set this bit depending on the nonpeer_pm variable of the mesh
iface sdata and when there are no active links on the interface it remains to
NL80211_MESH_POWER_UNKNOWN.
As soon as links starts to be established, it wil switch to
NL80211_MESH_POWER_ACTIVE as it is the value set by befault on the per sta
nonpeer_pm field.
As we want no power save by default, (as expressed with the per sta ini values),
lets init it to the expected default value of NL80211_MESH_POWER_ACTIVE.
Also please note that we cannot change the default value from userspace prior to
establishing a link as using NL80211_CMD_SET_MESH_CONFIG will not work before
NL80211_CMD_JOIN_MESH has been issued. So too late for our initial scan.
The powermanagement core does various actions when a powersupply changes.
It calls into notifiers, LED triggers, other power supplies and emits an uevent.
To make sure that all these actions happen properly call power_supply_changed().
Reported-by: Rajas Paranjpe <paranjperajas@gmail.com> Closes: https://github.com/MrChromebox/firmware/issues/420#issuecomment-2132251318 Signed-off-by: Thomas Weißschuh <linux@weissschuh.net> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pnp_bus_type is defined only when CONFIG_PNP=y, while being
not guarded by ifdeffery in the header. Moreover, it's not used
outside of the PNP code. Move it to the internal header to make
sure no-one will try to (ab)use it.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Update cpupower's P-State frequency calculation and reporting with AMD
Family 1Ah+ processors, when using the acpi-cpufreq driver. This is due
to a change in the PStateDef MSR layout in AMD Family 1Ah+.
If a write path in COW mode fails, either before submitting a bio for the
new extents or an actual IO error happens, we can end up allowing a fast
fsync to log file extent items that point to unwritten extents.
This is because dropping the extent maps happens when completing ordered
extents, at btrfs_finish_one_ordered(), and the completion of an ordered
extent is executed in a work queue.
This can result in a fast fsync to start logging file extent items based
on existing extent maps before the ordered extents complete, therefore
resulting in a log that has file extent items that point to unwritten
extents, resulting in a corrupt file if a crash happens after and the log
tree is replayed the next time the fs is mounted.
This can happen for both direct IO writes and buffered writes.
For example consider a direct IO write, in COW mode, that fails at
btrfs_dio_submit_io() because btrfs_extract_ordered_extent() returned an
error:
1) We call btrfs_finish_ordered_extent() with the 'uptodate' parameter
set to false, meaning an error happened;
2) That results in marking the ordered extent with the BTRFS_ORDERED_IOERR
flag;
3) btrfs_finish_ordered_extent() queues the completion of the ordered
extent - so that btrfs_finish_one_ordered() will be executed later in
a work queue. That function will drop extent maps in the range when
it's executed, since the extent maps point to unwritten locations
(signaled by the BTRFS_ORDERED_IOERR flag);
4) After calling btrfs_finish_ordered_extent() we keep going down the
write path and unlock the inode;
5) After that a fast fsync starts and locks the inode;
6) Before the work queue executes btrfs_finish_one_ordered(), the fsync
task sees the extent maps that point to the unwritten locations and
logs file extent items based on them - it does not know they are
unwritten, and the fast fsync path does not wait for ordered extents
to complete, which is an intentional behaviour in order to reduce
latency.
For the buffered write case, here's one example:
1) A fast fsync begins, and it starts by flushing delalloc and waiting for
the writeback to complete by calling filemap_fdatawait_range();
2) Flushing the dellaloc created a new extent map X;
3) During the writeback some IO error happened, and at the end io callback
(end_bbio_data_write()) we call btrfs_finish_ordered_extent(), which
sets the BTRFS_ORDERED_IOERR flag in the ordered extent and queues its
completion;
4) After queuing the ordered extent completion, the end io callback clears
the writeback flag from all pages (or folios), and from that moment the
fast fsync can proceed;
5) The fast fsync proceeds sees extent map X and logs a file extent item
based on extent map X, resulting in a log that points to an unwritten
data extent - because the ordered extent completion hasn't run yet, it
happens only after the logging.
To fix this make btrfs_finish_ordered_extent() set the inode flag
BTRFS_INODE_NEEDS_FULL_SYNC in case an error happened for a COW write,
so that a fast fsync will wait for ordered extent completion.
Note that this issues of using extent maps that point to unwritten
locations can not happen for reads, because in read paths we start by
locking the extent range and wait for any ordered extents in the range
to complete before looking for extent maps.
Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error code other than EINVAL, ENODEV or ETIME is returned
by acpi_ec_read() / acpi_ec_write(), then AE_OK is incorrectly
returned by acpi_ec_space_handler().
Fix this by only returning AE_OK on success, and return AE_ERROR
otherwise.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
[ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux / log