For Gen-1 targets like IPQ6018, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for IPQ6018 to mitigate this issue.
For Gen-1 targets like MSM8998, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for MSM8998 to mitigate this issue.
For Gen-1 targets like SM6350, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for SM6350 to mitigate this issue.
For Gen-1 targets like MSM8996, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for MSM8996 to mitigate this issue.
On the Qualcomm RB2 platform the I2C bus connected to the LT9611UXC
bridge under some circumstances can go into a state when all transfers
timeout. This causes both issues with fetching of EDID and with
updating of the bridge's firmware. While we are debugging the issue,
switch corresponding I2C bus to use i2c-gpio driver. While using
i2c-gpio no communication issues are observed.
This patch is asusmed to be a temporary fix, so it is implemented in a
non-intrusive manner to simply reverting it later.
On the Qualcomm RB1 platform the I2C bus connected to the LT9611UXC
bridge under some circumstances can go into a state when all transfers
timeout. This causes both issues with fetching of EDID and with
updating of the bridge's firmware. While we are debugging the issue,
switch corresponding I2C bus to use i2c-gpio driver. While using
i2c-gpio no communication issues are observed.
This patch is asusmed to be a temporary fix, so it is implemented in a
non-intrusive manner to simply reverting it later.
On SC7280, in host mode, it is observed that stressing out controller
results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instances in park mode for SC7280 to mitigate this issue.
Reported-by: Doug Anderson <dianders@google.com> Cc: stable@vger.kernel.org Fixes: bb9efa59c665 ("arm64: dts: qcom: sc7280: Add USB related nodes") Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20240604060659.1449278-3-quic_kriskura@quicinc.com Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SC7180, in host mode, it is observed that stressing out controller
results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instances in park mode for SC7180 to mitigate this issue.
Reported-by: Doug Anderson <dianders@google.com> Cc: stable@vger.kernel.org Fixes: 0b766e7fe5a2 ("arm64: dts: qcom: sc7180: Add USB related nodes") Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20240604060659.1449278-2-quic_kriskura@quicinc.com Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Samsung Galaxy Book Pro 360 (13" 2022 NT935QDB-KC71S) with codec SSID
144d:c1a4 requires the same workaround to enable the speaker amp
as other Samsung models with the ALC298 codec.
The MIDI2 gadget driver handled the default MIDI protocol version
incorrectly due to the confusion of the protocol version passed via
configfs (either 1 or 2) and UMP protocol bits (0x100 / 0x200).
As a consequence, the default protocol always resulted in MIDI1.
This patch addresses the misunderstanding of the protocol handling.
This adds sanity checks for ff offset. There is a check
on rt->first_free at first, but walking through by ff
without any check. If the second ff is a large offset.
We may encounter an out-of-bound read.
Signed-off-by: lei lu <llfamsec@gmail.com> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a check before visiting the members of ea to
make sure each ea stays within the ealist.
Signed-off-by: lei lu <llfamsec@gmail.com> Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds sanity checks for ocfs2_dir_entry to make sure all members of
ocfs2_dir_entry don't stray beyond valid memory region.
Link: https://lkml.kernel.org/r/20240626104433.163270-1-llfamsec@gmail.com Signed-off-by: lei lu <llfamsec@gmail.com> Reviewed-by: Heming Zhao <heming.zhao@suse.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no support for HWPOISON, MEMORY_FAILURE, or ARCH_HAS_COPY_MC on
s390. Therefore we do not expect to see VM_FAULT_HWPOISON in
do_exception().
However, since commit af19487f00f3 ("mm: make PTE_MARKER_SWAPIN_ERROR more
general"), it is possible to see VM_FAULT_HWPOISON in combination with
PTE_MARKER_POISONED, even on architectures that do not support HWPOISON
otherwise. In this case, we will end up on the BUG() in do_exception().
Fix this by treating VM_FAULT_HWPOISON the same as VM_FAULT_SIGBUS, similar
to x86 when MEMORY_FAILURE is not configured. Also print unexpected fault
flags, for easier debugging.
Note that VM_FAULT_HWPOISON_LARGE is not expected, because s390 cannot
support swap entries on other levels than PTE level.
Cc: stable@vger.kernel.org # 6.6+ Fixes: af19487f00f3 ("mm: make PTE_MARKER_SWAPIN_ERROR more general") Reported-by: Yunseong Kim <yskelg@gmail.com> Tested-by: Yunseong Kim <yskelg@gmail.com> Acked-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Message-ID: <20240715180416.3632453-1-gerald.schaefer@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We got the following issue in our fault injection stress test:
==================================================================
BUG: KASAN: slab-use-after-free in cachefiles_withdraw_cookie+0x4d9/0x600
Read of size 8 at addr ffff888118efc000 by task kworker/u78:0/109
After setting FSCACHE_CACHE_IS_WITHDRAWN, wait for all the cookie lookups
to complete first, and then wait for fscache_cache->object_count == 0 to
avoid the cookie exiting after the volume has been freed and triggering
the above issue. Therefore call fscache_withdraw_volume() before calling
cachefiles_withdraw_objects().
This way, after setting FSCACHE_CACHE_IS_WITHDRAWN, only the following two
cases will occur:
1) fscache_begin_lookup fails in fscache_begin_volume_access().
2) fscache_withdraw_volume() will ensure that fscache_count_object() has
been executed before calling fscache_wait_for_objects().
Fixes: fe2140e2f57f ("cachefiles: Implement volume support") Suggested-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Baokun Li <libaokun1@huawei.com> Link: https://lore.kernel.org/r/20240628062930.2467993-4-libaokun@huaweicloud.com Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Baokun Li <libaokun1@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We got the following issue in our fault injection stress test:
==================================================================
BUG: KASAN: slab-use-after-free in fscache_withdraw_volume+0x2e1/0x370
Read of size 4 at addr ffff88810680be08 by task ondemand-04-dae/5798
The fscache_volume in cache->volumes must not have been freed yet, but its
reference count may be 0. So use the new fscache_try_get_volume() helper
function try to get its reference count.
If the reference count of fscache_volume is 0, fscache_put_volume() is
freeing it, so wait for it to be removed from cache->volumes.
If its reference count is not 0, call cachefiles_withdraw_volume() with
reference count protection to avoid the above issue.
Fixes: fe2140e2f57f ("cachefiles: Implement volume support") Signed-off-by: Baokun Li <libaokun1@huawei.com> Link: https://lore.kernel.org/r/20240628062930.2467993-3-libaokun@huaweicloud.com Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Baokun Li <libaokun1@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we now want to sync the queues even when we're in RFKILL, we
shouldn't wake up the wait queue since we still expect to get all the
notifications from the firmware.
Fixes: 4d08c0b3357c ("wifi: iwlwifi: mvm: handle BA session teardown in RF-kill") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20240703064027.be7a9dbeacde.I5586cb3ca8d6e44f79d819a48a0c22351ff720c9@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As noticed by syzbot, calling ieee80211_handle_queued_frames()
(and actually handling frames there) requires softirqs to be
disabled, since we call into the RX code. Fix that in the case
of cleaning up frames left over during shutdown.
In nl80211, we always set the ssids of a scan request to
NULL when n_ssids==0 (passive scan). Drivers have relied
on this behaviour in the past, so we fixed it in 6 GHz
scan requests as well, and added a warning so we'd have
assurance the API would always be called that way.
syzbot found that wext doesn't ensure that, so we reach
the check and trigger the warning. Fix the wext code to
set the ssids pointer to NULL when there are none.
Once again, we've broken PASEMI Nemo boards with its incomplete
"interrupt-map" translations. Commit 935df1bd40d4 ("of/irq: Factor out
parsing of interrupt-map parent phandle+args from of_irq_parse_raw()")
changed the behavior resulting in the existing work-around not taking
effect. Rework the work-around to just skip parsing "interrupt-map" up
front by using the of_irq_imap_abusers list.
Fixes: 935df1bd40d4 ("of/irq: Factor out parsing of interrupt-map parent phandle+args from of_irq_parse_raw()") Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/86ed8ba2sp.wl-maz@kernel.org Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This BUG is the VM_BUG_ON(!in_atomic() && !irqs_disabled()) assertion in
folio_ref_try_add_rcu() for non-SMP kernel.
The process_vm_readv() calls GUP to pin the THP. An optimization for
pinning THP instroduced by commit 57edfcfd3419 ("mm/gup: accelerate thp
gup even for "pages != NULL"") calls try_grab_folio() to pin the THP,
but try_grab_folio() is supposed to be called in atomic context for
non-SMP kernel, for example, irq disabled or preemption disabled, due to
the optimization introduced by commit e286781d5f2e ("mm: speculative
page references").
The commit efa7df3e3bb5 ("mm: align larger anonymous mappings on THP
boundaries") is not actually the root cause although it was bisected to.
It just makes the problem exposed more likely.
The follow up discussion suggested the optimization for non-SMP kernel
may be out-dated and not worth it anymore [1]. So removing the
optimization to silence the BUG.
However calling try_grab_folio() in GUP slow path actually is
unnecessary, so the following patch will clean this up.
Link: https://lkml.kernel.org/r/20240625205350.1777481-1-yang@os.amperecomputing.com Fixes: 57edfcfd3419 ("mm/gup: accelerate thp gup even for "pages != NULL"") Signed-off-by: Yang Shi <yang@os.amperecomputing.com> Reported-by: kernel test robot <oliver.sang@intel.com> Tested-by: Oliver Sang <oliver.sang@intel.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Christoph Lameter <cl@linux.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Paul E. McKenney <paulmck@kernel.org> Cc: Rik van Riel <riel@surriel.com> Cc: Vivek Kasireddy <vivek.kasireddy@intel.com> Cc: <stable@vger.kernel.org> [6.6+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent fix introduced a reverse selection of
CONFIG_SERIAL_MULTI_INSTANTIATE, but its condition isn't always met.
Use a weak reverse selection to suggest the config for avoiding such
inconsistencies, instead.
Like other SPI controller flags, bits_per_word_mask may be used by a
peripheral driver, so it needs to reflect the capabilities of the
underlying controller.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Martin KaFai Lau <martin.lau@kernel.org> Link: https://lore.kernel.org/r/20240708133130.11609-2-daniel@iogearbox.net Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reported-and-tested-by: syzbot+efde959319469ff8d4d7@syzkaller.appspotmail.com Signed-off-by: Edward Adam Davis <eadavis@qq.com> Link: https://lore.kernel.org/r/tencent_8BBB6433BC9E1C1B7B4BDF1BF52574BA8808@qq.com Reported-and-tested-by: syzbot+01ade747b16e9c8030e0@syzkaller.appspotmail.com Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
...there are several warnings, and an error. This fixes all of those and
allows these tests to run and pass.
1. Fix linker error (undefined reference to memcpy) by providing a local
version of memcpy.
2. clang complains about using this form:
if (g = h & 0xf0000000)
...so factor out the assignment into a separate step.
3. The code is passing a signed const char* to elf_hash(), which expects
a const unsigned char *. There are several callers, so fix this at
the source by allowing the function to accept a signed argument, and
then converting to unsigned operations, once inside the function.
4. clang doesn't have __attribute__((externally_visible)) and generates
a warning to that effect. Fortunately, gcc 12 and gcc 13 do not seem
to require that attribute in order to build, run and pass tests here,
so remove it.
Reviewed-by: Carlos Llamas <cmllamas@google.com> Reviewed-by: Edward Liaw <edliaw@google.com> Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com> Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com> Signed-off-by: John Hubbard <jhubbard@nvidia.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
MS-SMB2 specification describes setting ->DeviceType to FILE_DEVICE_DISK
or FILE_DEVICE_CD_ROM. Set FILE_DEVICE_DISK instead of super magic in
FS_DEVICE_INFORMATION. And Set FILE_READ_ONLY_DEVICE for read-only share.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On the OMAPL138, the SPI reference clock is provided by the Power and
Sleep Controller (PSC). The PSC's datasheet says that 'some peripherals
have special programming requirements and additional recommended steps
you must take before you can invoke the PSC module state transition'. I
didn't find more details in documentation but it appears that PSC needs
the SPI to clear the POWERDOWN bit before disabling the clock. Indeed,
when this bit is set, the PSC gets stuck in transitions from enable to
disable state.
Clear the POWERDOWN bit when releasing driver's resources
While in commit 2dd33f9cec90 ("spi: imx: support DMA for imx35") it was
claimed that DMA works on i.MX25, i.MX31 and i.MX35 the respective
device trees don't add DMA channels. The Reference manuals of i.MX31 and
i.MX25 also don't mention the CSPI core being DMA capable. (I didn't
check the others.)
Since commit e267a5b3ec59 ("spi: spi-imx: Use dev_err_probe for failed
DMA channel requests") this results in an error message
spi_imx 43fa4000.spi: error -ENODEV: can't get the TX DMA channel!
during boot. However that isn't fatal and the driver gets loaded just
fine, just without using DMA.
ftrace_graph_ret_addr() takes an `idx` integer pointer that is used to
optimize the stack unwinding. Pass it a valid pointer to utilize the
optimizations that might be available in the future.
The commit is making riscv's usage of ftrace_graph_ret_addr() match
x86_64.
Currently, we stop all the counters while a new cpu is brought online.
However, the hpmevent to counter mappings are not reset. The firmware may
have some stale encoding in their mapping structure which may lead to
undesirable results. We have not encountered such scenario though.
The WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK should be set based on the
WOWLAN_KEK_KCK_MATERIAL command version. Currently, the command
version in the firmware has advanced to 4, which prevents the
flag from being set correctly, fix that.
Jan reported that 'cd ..' may take a long time in deep directory
hierarchies under a bind-mount. If concurrent renames happen it is
possible to livelock in is_subdir() because it will keep retrying.
Change is_subdir() from simply retrying over and over to retry once and
then acquire the rename lock to handle deep ancestor chains better. The
list of alternatives to this approach were less then pleasant. Change
the scope of rcu lock to cover the whole walk while at it.
A big thanks to Jan and Linus. Both Jan and Linus had proposed
effectively the same thing just that one version ended up being slightly
more elegant.
Reported-by: Jan Kara <jack@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the ref-verify tool, when processing the inline references of an extent
item, we may end up returning with uninitialized return value, because:
1) The 'ret' variable is not initialized if there are no inline extent
references ('ptr' == 'end' before the while loop starts);
2) If we find an extent owner inline reference we don't initialize 'ret'.
So fix these cases by initializing 'ret' to 0 when declaring the variable
and set it to -EINVAL if we find an extent owner inline references and
simple quotas are not enabled (as well as print an error message).
Reported-by: Mirsad Todorovac <mtodorovac69@gmail.com> Link: https://lore.kernel.org/linux-btrfs/59b40ebe-c824-457d-8b24-0bbca69d472b@gmail.com/ Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Potential out of bounds access in dml2_calculate_rq_and_dlg_params()
because the value of out_lowest_state_idx used as an index for FCLKChangeSupport
array can be greater than 1.
[How]
Currently dml2 core specifies identical values for all FCLKChangeSupport
elements. Always use index 0 in the condition to avoid out of bounds access.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Roman Li <Roman.Li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Some of the panels does not have the refresh rate range info
in base EDID and only have the refresh rate range info in
DisplayID block.
It will cause the max/min freesync refresh rate set to 0.
[How]
Try to parse the refresh rate range info from DisplayID if the
max/min refresh rate is 0.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Tom Chung <chiahsuan.chung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Description]
We need to ensure to take into account cursor prefetch BW in
mode support or we may pass ModeQuery but fail an actual flip
which will cause a hang. Flip may fail because the cursor_pre_bw
is populated during mode programming (and mode programming is
never called prior to ModeQuery).
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com> Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
We only enable the VRR while monitor usable refresh rate range
is greater than 10 Hz.
But we did not check the range in DRM_EDID_FEATURE_CONTINUOUS_FREQ
case.
[How]
Add a refresh rate range check before set the freesync_capable flag
in DRM_EDID_FEATURE_CONTINUOUS_FREQ case.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Jerry Zuo <jerry.zuo@amd.com> Signed-off-by: Tom Chung <chiahsuan.chung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sometimes, the on-disk metadata might be invalid due to user
interrupts, storage failures, or other unknown causes.
In that case, z_erofs_map_blocks_iter() may still return a valid
m_llen while other fields remain invalid (e.g., m_plen can be 0).
Due to the return value of z_erofs_scan_folio() in some path will
be ignored on purpose, the following z_erofs_scan_folio() could
then use the invalid value by accident.
The problem occurs between the system call to close the sock and hci_rx_work,
where the former releases the sock and the latter accesses it without lock protection.
If hci_rx_work processes the data that needs to be received before the sock is
closed, then everything is normal; Otherwise, the work thread may access the
released sock when receiving data.
Add a chan mutex in the rx callback of the sock to achieve synchronization between
the sock release and recv cb.
Sock is dead, so set chan data to NULL, avoid others use invalid sock pointer.
Reported-and-tested-by: syzbot+b7f6f8c9303466e16c8a@syzkaller.appspotmail.com Signed-off-by: Edward Adam Davis <eadavis@qq.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This sets the default power save mode setting to enabled.
The power save feature is now stable and stress test issues, such as the
TX timeout error, have been resolved.
commit c7ee0bc8db32 ("Bluetooth: btnxpuart: Resolve TX timeout error in
power save stress test")
With this setting, the driver will send the vendor command to FW at
startup, to enable power save feature.
User can disable this feature using the following vendor command:
hcitool cmd 3f 23 03 00 00 (HCI_NXP_AUTO_SLEEP_MODE)
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is reporting that calling hci_release_dev() from hci_error_reset()
due to hci_dev_put() from hci_error_reset() can cause deadlock at
destroy_workqueue(), for hci_error_reset() is called from
hdev->req_workqueue which destroy_workqueue() needs to flush.
We need to make sure that hdev->{rx_work,cmd_work,tx_work} which are
queued into hdev->workqueue and hdev->{power_on,error_reset} which are
queued into hdev->req_workqueue are no longer running by the moment
The 'missing-field-initializers' warning was reported
when building with W=2.
This patch use designated initializers for
'struct ffa_send_direct_data' to suppress the warning
and clarify the initialization intent.
The expander phy will be treated as broadcast flutter in the next
revalidation after the exp-attached end device probe failed, as follows:
[78779.654026] sas: broadcast received: 0
[78779.654037] sas: REVALIDATING DOMAIN on port 0, pid:10
[78779.654680] sas: ex 500e004aaaaaaa1f phy05 change count has changed
[78779.662977] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE)
[78779.662986] sas: ex 500e004aaaaaaa1f phy05 new device attached
[78779.663079] sas: ex 500e004aaaaaaa1f phy05:U:8 attached: 500e004aaaaaaa05 (stp)
[78779.693542] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] found
[78779.701155] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[78779.707864] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
...
[78835.161307] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[78835.171344] sas: sas_probe_sata: for exp-attached device 500e004aaaaaaa05 returned -19
[78835.180879] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] is gone
[78835.187487] sas: broadcast received: 0
[78835.187504] sas: REVALIDATING DOMAIN on port 0, pid:10
[78835.188263] sas: ex 500e004aaaaaaa1f phy05 change count has changed
[78835.195870] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE)
[78835.195875] sas: ex 500e004aaaaaaa1f rediscovering phy05
[78835.196022] sas: ex 500e004aaaaaaa1f phy05:U:A attached: 500e004aaaaaaa05 (stp)
[78835.196026] sas: ex 500e004aaaaaaa1f phy05 broadcast flutter
[78835.197615] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
The cause of the problem is that the related ex_phy's attached_sas_addr was
not cleared after the end device probe failed, so reset it.
Signed-off-by: Xingui Yang <yangxingui@huawei.com> Link: https://lore.kernel.org/r/20240619091742.25465-1-yangxingui@huawei.com Reviewed-by: John Garry <john.g.garry@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a PCI device is removed during eeh_pe_report_edev(), edev->pdev
will change and can cause a crash, hold the PCI rescan/remove lock
while taking a copy of edev->pdev->bus.
Reading the dispatch trace log from /sys/kernel/debug/powerpc/dtl/cpu-*
results in a BUG() when the config CONFIG_HARDENED_USERCOPY is enabled as
shown below.
Commit 6d07d1cd300f ("usercopy: Restrict non-usercopy caches to size 0")
requires that only whitelisted areas in slab/slub objects can be copied to
userspace when usercopy hardening is enabled using CONFIG_HARDENED_USERCOPY.
Dtl contains hypervisor dispatch events which are expected to be read by
privileged users. Hence mark this safe for user access.
Specify useroffset=0 and usersize=DISPATCH_LOG_BYTES to whitelist the
entire object.
mac802154 devices update their dev->stats fields locklessly. Therefore
these counters should be updated atomically. Adopt SMP safe DEV_STATS_INC()
and DEV_STATS_ADD() to achieve this.
Since the CONFIG_CTL register is only 32 bits wide in the Stromer
and Stromer Plus PLLs , the 'config_ctl_hi_val' values from the
IPQ5018 and IPQ5332 configurations are not used so remove those.
[How]
Disable MALL PG and make it always on until SMU firmware is ready.
Signed-off-by: Li Ma <li.ma@amd.com> Reviewed-by: Tim Huang <Tim.Huang@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When dmaengine supports pause function, in suspend state,
dmaengine_pause() is called instead of dmaengine_terminate_async(),
In end of playback stream, the runtime->state will go to
SNDRV_PCM_STATE_DRAINING, if system suspend & resume happen
at this time, application will not resume playback stream, the
stream will be closed directly, the dmaengine_terminate_async()
will not be called before the dmaengine_synchronize(), which
violates the call sequence for dmaengine_synchronize().
This behavior also happens for capture streams, but there is no
SNDRV_PCM_STATE_DRAINING state for capture. So use
dmaengine_tx_status() to check the DMA status if the status is
DMA_PAUSED, then call dmaengine_terminate_async() to terminate
dmaengine before dmaengine_synchronize().
Below is a summary of how the driver stores a reference to an skb during
transmit:
tx_buff[free_map[consumer_index]]->skb = new_skb;
free_map[consumer_index] = IBMVNIC_INVALID_MAP;
consumer_index ++;
Where variable data looks like this:
free_map == [4, IBMVNIC_INVALID_MAP, IBMVNIC_INVALID_MAP, 0, 3]
consumer_index^
tx_buff == [skb=null, skb=<ptr>, skb=<ptr>, skb=null, skb=null]
The driver has checks to ensure that free_map[consumer_index] pointed to
a valid index but there was no check to ensure that this index pointed
to an unused/null skb address. So, if, by some chance, our free_map and
tx_buff lists become out of sync then we were previously risking an
skb memory leak. This could then cause tcp congestion control to stop
sending packets, eventually leading to ETIMEDOUT.
Therefore, add a conditional to ensure that the skb address is null. If
not then warn the user (because this is still a bug that should be
patched) and free the old pointer to prevent memleak/tcp problems.
Signed-off-by: Nick Child <nnac123@linux.ibm.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If during the quota disable we fail when cleaning the quota tree or when
deleting the root from the root tree, we jump to the 'out' label without
ever dropping the reference on the quota root, resulting in a leak of the
root since fs_info->quota_root is no longer pointing to the root (we have
set it to NULL just before those steps).
Fix this by always doing a btrfs_put_root() call under the 'out' label.
This is a problem that exists since qgroups were first added in 2012 by
commit bed92eae26cc ("Btrfs: qgroup implementation and prototypes"), but
back then we missed a kfree on the quota root and free_extent_buffer()
calls on its root and commit root nodes, since back then roots were not
yet reference counted.
Reviewed-by: Boris Burkov <boris@bur.io> Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[BUG]
When running btrfs/060 with forced RST feature, it would crash the
following ASSERT() inside scrub_read_endio():
ASSERT(sector_nr < stripe->nr_sectors);
Before that, we would have tree dump from
btrfs_get_raid_extent_offset(), as we failed to find the RST entry for
the range.
[CAUSE]
Inside scrub_submit_extent_sector_read() every time we allocated a new
bbio we immediately called btrfs_map_block() to make sure there was some
RST range covering the scrub target.
But if btrfs_map_block() fails, we immediately call endio for the bbio,
while the bbio is newly allocated, it's completely empty.
Then inside scrub_read_endio(), we go through the bvecs to find
the sector number (as bi_sector is no longer reliable if the bio is
submitted to lower layers).
And since the bio is empty, such bvecs iteration would not find any
sector matching the sector, and return sector_nr == stripe->nr_sectors,
triggering the ASSERT().
[FIX]
Instead of calling btrfs_map_block() after allocating a new bbio, call
btrfs_map_block() first.
Since our only objective of calling btrfs_map_block() is only to update
stripe_len, there is really no need to do that after btrfs_alloc_bio().
This new timing would avoid the problem of handling empty bbio
completely, and in fact fixes a possible race window for the old code,
where if the submission thread is the only owner of the pending_io, the
scrub would never finish (since we didn't decrease the pending_io
counter).
Although the root cause of RST lookup failure still needs to be
addressed.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On the LG Gram 16Z90S, the WMAB and WMBB ACPI methods are not mapped
under \XINI, but instead are mapped under \_SB.XINI.
The reason for this is that the LGEX0820 ACPI device used by this
driver is mapped at \_SB.XINI, so the ACPI methods where moved as well
to appear below the LGEX0820 ACPI device.
Fix this by using the ACPI handle from the ACPI device when evaluating
both methods.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218901 Tested-by: Agathe Boutmy <agathe@boutmy.com> Signed-off-by: Armin Wolf <W_Armin@gmx.de> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20240606233540.9774-5-W_Armin@gmx.de Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The LGEX0815 ACPI device id is used for handling hotkey events, but
this functionality is already handled by the wireless-hotkey driver.
The LGEX0820 ACPI device id however is used to manage various
platform features using the WMAB/WMBB ACPI methods. Use this ACPI
device id to avoid blocking the wireless-hotkey driver from probing.
Tested-by: Agathe Boutmy <agathe@boutmy.com> Signed-off-by: Armin Wolf <W_Armin@gmx.de> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20240606233540.9774-4-W_Armin@gmx.de Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rfkill hotkey handling is already provided by the wireless-hotkey
driver. Remove the now unnecessary rfkill hotkey handling to avoid
duplicating functionality.
The ACPI notify handler still prints debugging information when
receiving ACPI notifications to aid in reverse-engineering.
Tested-by: Agathe Boutmy <agathe@boutmy.com> Signed-off-by: Armin Wolf <W_Armin@gmx.de> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20240606233540.9774-3-W_Armin@gmx.de Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The LGEX0815 ACPI device is used by the "LG Airplane Mode Button"
Windows driver for handling rfkill requests. When the ACPI device
receives an 0x80 ACPI notification, an rfkill event is to be
send to userspace.
Add support for the LGEX0815 ACPI device to the driver.
Tested-by: Agathe Boutmy <agathe@boutmy.com> Signed-off-by: Armin Wolf <W_Armin@gmx.de> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20240606233540.9774-2-W_Armin@gmx.de Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If sclp_init() fails it only partially cleans up: if there are multiple
failing calls to sclp_init() sclp_state_change_event will be added several
times to sclp_reg_list, which results in the following warning:
Fill this in so user-space can identify multiple ports on the same CP
unit.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the driver supports more devices over time the single MODULE_ALIAS
is complete and raises several warnings:
SPI driver ads7846 has no spi_device_id for ti,tsc2046
SPI driver ads7846 has no spi_device_id for ti,ads7843
SPI driver ads7846 has no spi_device_id for ti,ads7845
SPI driver ads7846 has no spi_device_id for ti,ads7873
Fix this by adding a spi_device_id table and removing the manual
MODULE_ALIAS.
If the ASP1 DAI is hooked up by the machine driver the ASP TX mixer
sources should be initialized to disconnected. There aren't currently
any available products using the ASP so this doesn't affect any
existing systems.
The cs35l56 does not have any fixed default for the mixer source
registers. When the cs35l56 boots, its firmware patches these registers
to setup a system-specific routing; this is so that Windows can use
generic SDCA drivers instead of needing knowledge of chip-specific
registers. The setup varies between end-products, which each have
customized firmware, and so the default register state varies between
end-products. It can also change if the firmware on an end-product is
upgraded - for example if a change was needed to the routing for Windows
use-cases. It must be emphasized that the settings applied by the
firmware are not internal magic tuning; they are statically implementing
use-case setup that on Linux would be done via ALSA controls.
The driver is currently syncing the mixer controls with whatever
initial state the firmware wrote to the registers, so that they report
the actual audio routing. But if the ASP DAI is hooked up this can create
a powered-up DAPM graph without anything intentionally setting up a path.
This can lead to parts of the audio system powering up unexpectedly.
For example when cs35l56 is connected to cs42l43 using a codec-codec link,
this can create a complete DAPM graph which then powers-up cs42l43. But
the cs42l43 can only be clocked from its SoundWire bus so this causes a
bunch of errors in the kernel log where cs42l43 is unexpectedly powered-up
without a clock.
If the host is taking ownership of the ASP (either directly or as a
codec-to-codec link) there is no need to keep the mixer settings that the
firmware wrote. The driver has ALSA controls for setting these using
standard Linux mechanisms. So if the machine driver hooks up the ASP the
ASP mixers are initialized to "None" (no input). This prevents unintended
DAPM-graph power-ups, and means the initial state of the mixers is
always going to be None.
Since the initial state of the mixers can vary from system to system and
potentially between firmware upgrades, no use-case manager can currently
assume that cs35l56 has a known initial state. The firmware could just as
easily default them to "None" as to any input source. So defaulting them
to "None" in the driver is not increasing the entropy of the system.
The minimum period size was enforced to 64 as older devices integrating
McASP with EDMA used an internal FIFO of 64 samples.
With UDMA based platforms this internal McASP FIFO is optional, as the
DMA engine internally does some buffering which is already accounted for
when registering the platform. So we should read the actual FIFO
configuration (txnumevt/rxnumevt) instead of hardcoding frames.min to
64.
Sometimes the stream may be stopped due to XRUN events, in which case
the userspace can call snd_pcm_drop() and snd_pcm_prepare() to stop and
start the stream again.
In these cases, we must wait for the DMA channel to synchronize before
marking the stream as prepared for playback, as the DMA channel gets
stopped by drop() without any synchronization. Make sure the ALSA core
synchronizes the DMA channel by adding a sync_stop() hook.
When headphones are plugged in, they appear absent; when they are removed,
they appear present.
Add a specific entry in bytcr_rt5640 for this device
Signed-off-by: Thomas GENTY <tomlohave@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20240608170251.99936-1-tomlohave@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Most users after parsing a topology file, release memory used by it, so
having pointer references directly into topology file contents is wrong.
Use devm_kmemdup(), to allocate memory as needed.
The Lenovo N24 on resume becomes stuck in a state where it
sends incorrect packets, causing elantech_packet_check_v4 to fail.
The only way for the device to resume sending the correct packets is for
it to be disabled and then re-enabled.
This change adds a dmi check to trigger this behavior on resume.
projects / linux / log