Fix kernel crash in AP bus code caused by very early invocation of the
config change callback function via SCLP.
After a fresh IML of the machine the crypto cards are still offline and
will get switched online only with activation of any LPAR which has the
card in it's configuration. A crypto card coming online is reported
to the LPAR via SCLP and the AP bus offers a callback function to get
this kind of information. However, it may happen that the callback is
invoked before the AP bus init function is complete. As the callback
triggers a synchronous AP bus scan, the scan may already run but some
internal states are not initialized by the AP bus init function resulting
in a crash like this:
This patch improves the ap_bus_force_rescan() function which is
invoked by the config change callback by checking if a first
initial AP bus scan has been done. If not, the force rescan request
is simple ignored. Anyhow it does not make sense to trigger AP bus
re-scans even before the very first bus scan is complete.
During SMBus block data read process, we have seen high interrupt rate
because of TX_EMPTY irq status while waiting for block length byte (the
first data byte after the address phase). The interrupt handler does not
do anything because the internal state is kept as STATUS_WRITE_IN_PROGRESS.
Hence, we should disable TX_EMPTY IRQ until I2C DesignWare receives
first data byte from I2C device, then re-enable it to resume SMBus
transaction.
It takes 0.789 ms for host to receive data length from slave.
Without the patch, i2c_dw_isr() is called 99 times by TX_EMPTY interrupt.
And it is none after applying the patch.
Cc: stable@vger.kernel.org Co-developed-by: Chuong Tran <chuong@os.amperecomputing.com> Signed-off-by: Chuong Tran <chuong@os.amperecomputing.com> Signed-off-by: Tam Nguyen <tamnguyenchi@os.amperecomputing.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit abd3ac7902fb ("watchdog: sbsa: Support architecture version 1")
introduced new timer math for watchdog revision 1 with the 48 bit offset
register.
The gwdt->clk and timeout are u32, but the argument being calculated is
u64. Without a cast, the compiler performs u32 operations, truncating
intermediate steps, resulting in incorrect values.
A watchdog revision 1 implementation with a gwdt->clk of 1GHz and a
timeout of 600s writes 3647256576 to the one shot watchdog instead of 300000000000, resulting in the watchdog firing in 3.6s instead of 600s.
Force u64 math by casting the first argument (gwdt->clk) as a u64. Make
the order of operations explicit with parenthesis.
-EOPNOTSUPP is the return value that implements a "no-op" hook, not 0.
Without this fix having only the BPF LSM enabled (with no programs
attached) can cause uninitialized variable reads in
nfsd4_encode_fattr(), because the BPF hook returns 0 without touching
the 'ctxlen' variable and the corresponding 'contextlen' variable in
nfsd4_encode_fattr() remains uninitialized, yet being treated as valid
based on the 0 return value.
Cc: stable@vger.kernel.org Fixes: 98e828a0650f ("security: Refactor declaration of LSM hooks") Reported-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intent for the commit was to be able to detect carrier loss/gain
for just the NIC connected to the BMC. The unwanted effect is a
carrier loss for auxiliary paths also causes the BMC to lose
carrier. The BMC never regains carrier despite the secondary NIC
regaining a link.
This change, when merged, needs to be backported to stable kernels.
5.4-stable, 5.10-stable, 5.15-stable, 6.1-stable, 6.5-stable
Fixes: 3780bb29311e ("ncsi: Propagate carrier gain/loss events to the NCSI controller") CC: stable@vger.kernel.org Signed-off-by: Johnathan Mantey <johnathanx.mantey@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HP 255 G10 has a mute LED that can be made to work using quirk
ALC236_FIXUP_HP_MUTE_LED_COEFBIT2.
Enable already existing quirk - at correct line to keep order
Add ALC295 to pin fall back table.
Remove 5 pin quirks for Dell ALC295.
ALC295 was only support MIC2 for external MIC function.
ALC295 assigned model "ALC269_FIXUP_DELL1_MIC_NO_PRESENCE" for pin
fall back table.
It was assigned wrong model. So, let's remove it.
Fixes: fbc571290d9f ("ALSA: hda/realtek - Fixed Headphone Mic can't record on Dell platform") Signed-off-by: Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/7c1998e873834df98d59bd7e0d08c72e@realtek.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported recently, ALSA core info helper may cause a deadlock at
the forced device disconnection during the procfs operation.
The proc_remove() (that is called from the snd_card_disconnect()
helper) has a synchronization of the pending procfs accesses via
wait_for_completion(). Meanwhile, ALSA procfs helper takes the global
mutex_lock(&info_mutex) at both the proc_open callback and
snd_card_info_disconnect() helper. Since the proc_open can't finish
due to the mutex lock, wait_for_completion() never returns, either,
hence it deadlocks.
This patch is a workaround for avoiding the deadlock scenario above.
The basic strategy is to move proc_remove() call outside the mutex
lock. proc_remove() can work gracefully without extra locking, and it
can delete the tree recursively alone. So, we call proc_remove() at
snd_info_card_disconnection() at first, then delete the rest resources
recursively within the info_mutex lock.
After the change, the function snd_info_disconnect() doesn't do
disconnection by itself any longer, but it merely clears the procfs
pointer. So rename the function to snd_info_clear_entries() for
avoiding confusion.
The similar change is applied to snd_info_free_entry(), too. Since
the proc_remove() is called only conditionally with the non-NULL
entry->p, it's skipped after the snd_info_clear_entries() call.
This happens because -EAGAIN error returned from btrfs_reserve_extent()
called from btrfs_new_extent_direct() is spilling over to the userland.
btrfs_reserve_extent() returns -EAGAIN when there is no active zone
available. Then, the caller should wait for some other on-going IO to
finish a zone and retry the allocation.
This logic is already implemented for buffered write in cow_file_range(),
but it is missing for the direct IO counterpart. Implement the same logic
for it.
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com> Fixes: 2ce543f47843 ("btrfs: zoned: wait until zone is finished when allocation didn't progress") CC: stable@vger.kernel.org # 6.1+ Tested-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because on v3 inodes, di_flushiter doesn't exist. It overlaps with
zero padding in the inode, except when NREXT64=1 configurations are
in use and the zero padding is no longer padding but holds the 64
bit extent counter.
This manifests obviously on big endian platforms (e.g. s390) because
the log dinode is in host order and the overlap is the LSBs of the
extent count field. It is not noticed on little endian machines
because the overlap is at the MSB end of the extent count field and
we need to get more than 2^^48 extents in the inode before it
manifests. i.e. the heat death of the universe will occur before we
see the problem in little endian machines.
This is a zero-day issue for NREXT64=1 configuraitons on big endian
machines. Fix it by only clearing di_flushiter on v2 inodes during
recovery.
Fixes: 9b7d16e34bbe ("xfs: Introduce XFS_DIFLAG2_NREXT64 and associated helpers")
cc: stable@kernel.org # 5.19+ Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: "Darrick J. Wong" <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandanbabu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each smb_rqst struct contains two things: an array of kvecs (rq_iov) that
contains the protocol data for an RPC op and an iterator (rq_iter) that
contains the data payload of an RPC op. When an smb_rqst is allocated
rq_iter is it always cleared, but we don't set it up unless we're going to
use it.
The functions that determines the size of the ciphertext buffer that will
be needed to encrypt a request, cifs_get_num_sgs(), assumes that rq_iter is
always initialised - and employs user_backed_iter() to check that the
iterator isn't user-backed. This used to incidentally work, because
->user_backed was set to false because the iterator has never been
initialised, but with commit f1b4cb650b9a0eeba206d8f069fcdc532bfbcd74[1]
which changes user_backed_iter() to determine this based on the iterator
type insted, a warning is now emitted:
The problem is that rq_iter was never set, so the type is 0 (ie. ITER_UBUF)
which causes user_backed_iter() to return true. The code doesn't
malfunction because it checks the size of the iterator - which is 0.
Fix cifs_get_num_sgs() to ignore rq_iter if its count is 0, thereby
bypassing the warnings.
It might be better to explicitly initialise rq_iter to a zero-length
ITER_BVEC, say, as it can always be reinitialised later.
Fixes: d08089f649a0 ("cifs: Change the I/O paths to use an iterator rather than a page list") Reported-by: Damian Tometzki <damian@riscv-rocks.de> Closes: https://lore.kernel.org/r/ZUfQo47uo0p2ZsYg@fedora.fritz.box/ Tested-by: Damian Tometzki <damian@riscv-rocks.de> Cc: stable@vger.kernel.org
cc: Eric Biggers <ebiggers@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=f1b4cb650b9a0eeba206d8f069fcdc532bfbcd74 Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the mount command has specified multichannel as a mount option,
but multichannel is found to be unsupported by the server at the time
of mount, we set chan_max to 1. Which means that the user needs to
remount the share if the server starts supporting multichannel.
This change removes this reset. What it means is that if the user
specified multichannel or max_channels during mount, and at this
time, multichannel is not supported, but the server starts supporting
it at a later point, the client will be capable of scaling out the
number of channels.
Cc: stable@vger.kernel.org Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a session reconnect, it is possible that the
server moved to another physical server (happens in case
of Azure files). So at this time, force a query of server
interfaces again (in case of multichannel session), such
that the secondary channels connect to the right
IP addresses (possibly updated now).
Cc: stable@vger.kernel.org Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We introduced a helper function to be used by non-cifsd threads to
mark the connection for reconnect. For multichannel, when only
a particular channel needs to be reconnected, this had a bug.
This change fixes that by marking that particular channel
for reconnect.
Fixes: dca65818c80c ("cifs: use a different reconnect helper for non-cifsd threads") Cc: stable@vger.kernel.org Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All release_mid() callers seem to hold a reference of @mid so there is
no need to call kref_put(&mid->refcount, __release_mid) under
@server->mid_lock spinlock. If they don't, then an use-after-free bug
would have occurred anyways.
By getting rid of such spinlock also fixes a potential deadlock as
shown below
CPU 0 CPU 1
------------------------------------------------------------------
cifs_demultiplex_thread() cifs_debug_data_proc_show()
release_mid()
spin_lock(&server->mid_lock);
spin_lock(&cifs_tcp_ses_lock)
spin_lock(&server->mid_lock)
__release_mid()
smb2_find_smb_tcon()
spin_lock(&cifs_tcp_ses_lock) *deadlock*
Cc: stable@vger.kernel.org Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following UAF was triggered when running fstests generic/072 with
KASAN enabled against Windows Server 2022 and mount options
'multichannel,max_channels=2,vers=3.1.1,mfsymlinks,noperm'
BUG: KASAN: slab-use-after-free in smb2_query_info_compound+0x423/0x6d0 [cifs]
Read of size 8 at addr ffff888014941048 by task xfs_io/27534
This is a race between open_cached_dir() and cached_dir_lease_break()
where the cache entry for the open directory handle receives a lease
break while creating it. And before returning from open_cached_dir(),
we put the last reference of the new @cfid because of
!@cfid->has_lease.
Besides the UAF, while running xfstests a lot of missed lease breaks
have been noticed in tests that run several concurrent statfs(2) calls
on those cached fids
CIFS: VFS: \\w22-root1.gandalf.test No task to wake, unknown frame...
CIFS: VFS: \\w22-root1.gandalf.test Cmd: 18 Err: 0x0 Flags: 0x1...
CIFS: VFS: \\w22-root1.gandalf.test smb buf 00000000715bfe83 len 108
CIFS: VFS: Dump pending requests:
CIFS: VFS: \\w22-root1.gandalf.test No task to wake, unknown frame...
CIFS: VFS: \\w22-root1.gandalf.test Cmd: 18 Err: 0x0 Flags: 0x1...
CIFS: VFS: \\w22-root1.gandalf.test smb buf 000000005aa7316e len 108
...
To fix both, in open_cached_dir() ensure that @cfid->has_lease is set
right before sending out compounded request so that any potential
lease break will be get processed by demultiplex thread while we're
still caching @cfid. And, if open failed for some reason, re-check
@cfid->has_lease to decide whether or not put lease reference.
Cc: stable@vger.kernel.org Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When multiple mounts are to the same share from the same client it was not
possible to determine which section of /proc/fs/cifs/Stats (and DebugData)
correspond to that mount. In some recent examples this turned out to be
a significant problem when trying to analyze performance data - since
there are many cases where unless we know the tree id and session id we
can't figure out which stats (e.g. number of SMB3.1.1 requests by type,
the total time they take, which is slowest, how many fail etc.) apply to
which mount. The only existing loosely related ioctl CIFS_IOC_GET_MNT_INFO
does not return the information needed to uniquely identify which tcon
is which mount although it does return various flags and device info.
Add a cifs.ko ioctl CIFS_IOC_GET_TCON_INFO (0x800ccf0c) to return tid,
session id, tree connect count.
Cc: stable@vger.kernel.org Reviewed-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For example:
touch -h -t 02011200 testfile
where testfile is a symlink would not change the timestamp, but
touch -t 02011200 testfile
does work to change the timestamp of the target
Suggested-by: David Howells <dhowells@redhat.com> Reported-by: Micah Veilleux <micah.veilleux@iba-group.com> Closes: https://bugzilla.samba.org/show_bug.cgi?id=14476 Cc: stable@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes some xfstests including generic/564 and generic/157
The "sfu" mount option can be useful for creating special files (character
and block devices in particular) but could not create FIFOs. It did
recognize existing empty files with the "system" attribute flag as FIFOs
but this is too general, so to support creating FIFOs more safely use a new
tag (but the same length as those for char and block devices ie "IntxLNK"
and "IntxBLK") "LnxFIFO" to indicate that the file should be treated as a
FIFO (when mounted with the "sfu"). For some additional context note that
"sfu" followed the way that "Services for Unix" on Windows handled these
special files (at least for character and block devices and symlinks),
which is different than newer Windows which can handle special files
as reparse points (which isn't an option to many servers).
Cc: stable@vger.kernel.org Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct timespec64 has unused bits in the tv_nsec field that can be used
for other purposes. In future patches, we're going to change how the
inode->i_ctime is accessed in certain inodes in order to make use of
them. In order to do that safely though, we'll need to eradicate raw
accesses of the inode->i_ctime field from the kernel.
Add new accessor functions for the ctime that we use to replace them.
Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Message-Id: <20230705185812.579118-2-jlayton@kernel.org> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the low-power states of the underlying platform to enable runtime PM.
If the platform doesn't support runtime D3, then enabling default RPM will
result in the controller malfunctioning, as in the case of hotplug devices
not being detected because of a failed interrupt generation.
When calculating the pfn for the iitlbt/idtlbt instruction, do not
drop the upper 5 address bits. This doesn't seem to have an effect
on physical hardware which uses less physical address bits, but in
qemu the missing bits are visible.
Bail out early with error message when trying to boot a 64-bit kernel on
32-bit machines. This fixes the previous commit to include the check for
true 64-bit kernels as well.
When dealing with hugetlb pages, manipulating struct page pointers
directly can get to wrong struct page, since struct page is not guaranteed
to be contiguous on SPARSEMEM without VMEMMAP. Use nth_page() to handle
it properly.
A wrong or non-existing page might be tried to be grabbed, either
leading to a non freeable page or kernel memory access errors. No bug
is reported. It comes from code inspection.
Link: https://lkml.kernel.org/r/20230913201248.452081-3-zi.yan@sent.com Fixes: 57a196a58421 ("hugetlb: simplify hugetlb handling in follow_page_mask") Signed-off-by: Zi Yan <ziy@nvidia.com> Reviewed-by: Muchun Song <songmuchun@bytedance.com> Cc: David Hildenbrand <david@redhat.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
follow_page() doesn't use FOLL_PIN, meanwhile hugetlb seems to not be the
target of FOLL_WRITE either. However add the checks.
Namely, either the need to CoW due to missing write bit, or proper
unsharing on !AnonExclusive pages over R/O pins to reject the follow page.
That brings this function closer to follow_hugetlb_page().
So we don't care before, and also for now. But we'll care if we switch
over slow-gup to use hugetlb_follow_page_mask(). We'll also care when to
return -EMLINK properly, as that's the gup internal api to mean "we should
unshare". Not really needed for follow page path, though.
When at it, switching the try_grab_page() to use WARN_ON_ONCE(), to be
clear that it just should never fail. When error happens, instead of
setting page==NULL, capture the errno instead.
Link: https://lkml.kernel.org/r/20230628215310.73782-3-peterx@redhat.com Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jason Gunthorpe <jgg@nvidia.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Kirill A . Shutemov <kirill@shutemov.name> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Yang Shi <shy828301@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: 426056efe835 ("mm/hugetlb: use nth_page() in place of direct struct page manipulation") Signed-off-by: Sasha Levin <sashal@kernel.org>
The stuttering code isn't functioning as expected. Ideally, it should
pause the torture threads for a designated period before resuming. Yet,
it fails to halt the test for the correct duration. Additionally, a race
condition exists, potentially causing the stuttering code to pause for
an extended period if the 'spt' variable is non-zero due to the stutter
orchestration thread's inadequate CPU time.
Moreover, over-stuttering can hinder RCU's progress on TREE07 kernels.
This happens as the stuttering code may run within a softirq due to RCU
callbacks. Consequently, ksoftirqd keeps a CPU busy for several seconds,
thus obstructing RCU's progress. This situation triggers a warning
message in the logs:
This warning suggests that an RCU torture object, although invisible to
RCU readers, couldn't make it past the pipe array and be freed -- a
strong indication that there weren't enough grace periods during the
stutter interval.
To address these issues, this patch sets the "stutter end" time to an
absolute point in the future set by the main stutter thread. This is
then used for waiting in stutter_wait(). While the stutter thread still
defines this absolute time, the waiters' waiting logic doesn't rely on
the stutter thread receiving sufficient CPU time to halt the stuttering
as the halting is now self-controlled.
Cc: stable@vger.kernel.org Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current torture-test sleeps are waiting for a duration, but there
are situations where it is better to wait for an absolute time, for
example, when ending a stutter interval. This commit therefore adds
an hrtimer mode parameter to torture_hrtimeout_ns(). Why not also the
other torture_hrtimeout_*() functions? The theory is that most absolute
times will be in nanoseconds, especially not (say) jiffies.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Stable-dep-of: cca42bd8eb1b ("rcutorture: Fix stuttering races and other issues") Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to gain better race coverage, move the test start/stop
waits in stutter_wait() to torture_hrtimeout_jiffies().
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Stable-dep-of: cca42bd8eb1b ("rcutorture: Fix stuttering races and other issues") Signed-off-by: Sasha Levin <sashal@kernel.org>
Given that it is expected that more code will use torture_hrtimeout_*(),
including for longer timeouts, make it use TASK_IDLE instead of
TASK_UNINTERRUPTIBLE.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Stable-dep-of: cca42bd8eb1b ("rcutorture: Fix stuttering races and other issues") Signed-off-by: Sasha Levin <sashal@kernel.org>
This commit adds a kthread-creation callback to the
_torture_create_kthread() function, which allows callers of a new
torture_create_kthread_cb() macro to specify a function to be invoked
after the kthread is created but before it is awakened for the first time.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Cc: Dietmar Eggemann <dietmar.eggemann@arm.com> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Juri Lelli <juri.lelli@redhat.com> Cc: Valentin Schneider <vschneid@redhat.com> Cc: Dietmar Eggemann <dietmar.eggemann@arm.com> Cc: kernel-team@android.com Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org> Acked-by: John Stultz <jstultz@google.com>
Stable-dep-of: cca42bd8eb1b ("rcutorture: Fix stuttering races and other issues") Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit ac91e6980563 ("PCI: Unify delay handling for reset and resume")
shortened an unconditional 1 sec delay after a Secondary Bus Reset to 100
msec for PCIe (per PCIe r6.1 sec 6.6.1). The 1 sec delay is only required
for Conventional PCI.
But it turns out that there are PCIe devices which require a longer delay
than prescribed before first config space access after reset recovery or
resume from D3cold:
Chad reports that a "VideoPropulsion Torrent QN16e" MPEG QAM Modulator
"raises a PCI system error (PERR), as reported by the IPMI event log, and
the hardware itself would suffer a catastrophic event, cycling the server"
unless the longer delay is observed.
The card is specified to conform to PCIe r1.0 and indeed only supports Gen1
speed (2.5 GT/s) according to lspci. PCIe r1.0 sec 7.6 prescribes the same
100 msec delay as PCIe r6.1 sec 6.6.1:
To allow components to perform internal initialization, system software
must wait for at least 100 ms from the end of a reset (cold/warm/hot)
before it is permitted to issue Configuration Requests
The behavior of the Torrent QN16e card thus appears to be a quirk. Treat
it as such and lengthen the reset delay for this specific device.
Fixes: ac91e6980563 ("PCI: Unify delay handling for reset and resume") Link: https://lore.kernel.org/r/47727e792c7f0282dc144e3ec8ce8eb6e713394e.1695304512.git.lukas@wunner.de Reported-by: Chad Schroeder <CSchroeder@sonifi.com> Closes: https://lore.kernel.org/linux-pci/DM6PR16MB2844903E34CAB910082DF019B1FAA@DM6PR16MB2844.namprd16.prod.outlook.com/ Tested-by: Chad Schroeder <CSchroeder@sonifi.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org # v5.4+ Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, The imx pgc power domain doesn't set the fwnode
pointer, which results in supply regulator device can't get
consumer imx pgc power domain device from fwnode when creating
a link.
This causes the driver core to instead try to create a link
between the parent gpc device of imx pgc power domain device and
supply regulator device. However, at this point, the gpc device
has already been bound, and the link creation will fail. So adding
the fwnode pointer to the imx pgc power domain device will fix
this issue.
Signed-off-by: Pengfei Li <pengfei.li_1@nxp.com> Tested-by: Emil Kronborg <emil.kronborg@protonmail.com> Fixes: 3fb16866b51d ("driver core: fw_devlink: Make cycle detection more robust") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20231020185949.537083-1-pengfei.li_1@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit c494a447c14e ("soc: bcm: bcm2835-power: Refactor ASB control")
refactored the ASB control by using a general function to handle both
the enable and disable. But this patch introduced a subtle regression:
we need to check if !!(readl(base + reg) & ASB_ACK) == enable, not just
check if (readl(base + reg) & ASB_ACK) == true.
Currently, this is causing an invalid register state in V3D when
unloading and loading the driver, because `bcm2835_asb_disable()` will
return -ETIMEDOUT and `bcm2835_asb_power_off()` will fail to disable the
ASB slave for V3D.
The CXL subsystem, at cxl_mem ->probe() time, establishes a lineage of
ports (struct cxl_port objects) between an endpoint and the root of a
CXL topology. Each port including the endpoint port is attached to the
cxl_port driver.
Given that setup, it follows that when either any port in that lineage
goes through a cxl_port ->remove() event, or the memdev goes through a
cxl_mem ->remove() event. The hierarchy below the removed port, or the
entire hierarchy if the memdev is removed needs to come down.
The delete_endpoint() callback is careful to check whether it is being
called to tear down the hierarchy, or if it is only being called to
teardown the memdev because an ancestor port is going through
->remove().
That care needs to take the device_lock() of the endpoint's parent.
Which requires 2 bugs to be fixed:
1/ A reference on the parent is needed to prevent use-after-free
scenarios like this signature:
BUG: spinlock bad magic on CPU#0, kworker/u56:0/11
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS edk2-20230524-3.fc38 05/24/2023
Workqueue: cxl_port detach_memdev [cxl_core]
RIP: 0010:spin_bug+0x65/0xa0
Call Trace:
do_raw_spin_lock+0x69/0xa0
__mutex_lock+0x695/0xb80
delete_endpoint+0xad/0x150 [cxl_core]
devres_release_all+0xb8/0x110
device_unbind_cleanup+0xe/0x70
device_release_driver_internal+0x1d2/0x210
detach_memdev+0x15/0x20 [cxl_core]
process_one_work+0x1e3/0x4c0
worker_thread+0x1dd/0x3d0
2/ In the case of RCH topologies, the parent device that needs to be
locked is not always @port->dev as returned by cxl_mem_find_port(), use
endpoint->dev.parent instead.
Fixes: 8dd2bc0f8e02 ("cxl/mem: Add the cxl_mem driver") Cc: <stable@vger.kernel.org> Reported-by: Robert Richter <rrichter@amd.com> Closes: http://lore.kernel.org/r/20231018171713.1883517-2-rrichter@amd.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Root decoder granularity must match value from CFWMS, which may not
be the region's granularity for non-interleaved root decoders.
So when calculating granularities for host bridge decoders, use the
region's granularity instead of the root decoder's granularity to ensure
the correct granularities are set for the host bridge decoders and any
downstream switch decoders.
Test configuration is 1 host bridge * 2 switches * 2 endpoints per switch.
Region created with 2048 granularity using following command line:
Use "cxl list -PDE | grep granularity" to get a view of the granularity
set at each level of the topology.
Before this patch:
"interleave_granularity":2048,
"interleave_granularity":2048,
"interleave_granularity":512,
"interleave_granularity":2048,
"interleave_granularity":2048,
"interleave_granularity":512,
"interleave_granularity":256,
BIT 20: TIMEOUT error
The module has stalled too long in a frame. This happens when:
- The TX FIFO or RX FIFO is not handled and the bus is stuck in the
middle of a message,
- No STOP was issued and between messages,
- IBI manual is used and no decision was made.
The maximum stall period is 100 μs.
This can be considered as being just a warning as the system IRQ latency
can easily be greater than 100us.
Upon IBIWON timeout, the SDA line will always be kept low if we don't emit
a stop. Calling svc_i3c_master_emit_stop() there will let the bus return to
idle state.
MSTATUS[RXPEND] is only updated after the data transfer cycle started. This
creates an issue when the I3C clock is slow, and the CPU is running fast
enough that MSTATUS[RXPEND] may not be updated when the code reaches
checking point. As a result, mandatory data can be missed.
Add a wait for MSTATUS[COMPLETE] to ensure that all mandatory data is
already in FIFO. It also works without mandatory data.
If an In-Band Interrupt (IBI) occurs and IBI work thread is not immediately
scheduled, when svc_i3c_master_priv_xfers() initiates the I3C transfer and
attempts to send address 0x7e, the target interprets it as an
IBI handler and returns the target address 0x0a.
However, svc_i3c_master_priv_xfers() does not handle this case and proceeds
with other transfers, resulting in incorrect data being returned.
Add IBIWON check in svc_i3c_master_xfer(). In case this situation occurs,
return a failure to the driver.
The ibi work thread operates asynchronously with other transfers, such as
svc_i3c_master_priv_xfers(). Introduce mutex protection to ensure the
completion of the entire i3c/i2c transaction.
Commit 5e42bcbc3fef ("cxl/region: decrement ->nr_targets on error in
cxl_region_attach()") tried to avoid 'eiw' initialization errors when
->nr_targets exceeded 16, by just decrementing ->nr_targets when
cxl_region_setup_targets() failed.
Commit 86987c766276 ("cxl/region: Cleanup target list on attach error")
extended that cleanup to also clear cxled->pos and p->targets[pos]. The
initialization error was incidentally fixed separately by:
Commit 8d4285425714 ("cxl/region: Fix port setup uninitialized variable
warnings") which was merged a few days after 5e42bcbc3fef.
But now the original cleanup when cxl_region_setup_targets() fails
prevents endpoint and switch decoder resources from being reused:
1) the cleanup does not set the decoder's region to NULL, which results
in future dpa_size_store() calls returning -EBUSY
2) the decoder is not properly freed, which results in future commit
errors associated with the upstream switch
Now that the initialization errors were fixed separately, the proper
cleanup for this case is to just return immediately. Then the resources
associated with this target get cleanup up as normal when the failed
region is deleted.
The ->nr_targets decrement in the error case also helped prevent
a p->targets[] array overflow, so add a new check to prevent against
that overflow.
Tested by trying to create an invalid region for a 2 switch * 2 endpoint
topology, and then following up with creating a valid region.
Fixes: 5e42bcbc3fef ("cxl/region: decrement ->nr_targets on error in cxl_region_attach()") Cc: <stable@vger.kernel.org> Signed-off-by: Jim Harris <jim.harris@samsung.com> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Acked-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/169703589120.1202031.14696100866518083806.stgit@bgt-140510-bm03.eng.stellus.in Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the offset into the device when looking for OTP
bits can go outside of the address of the MTD NOR devices,
and if that memory isn't readable, bad things happen
on the IXP4xx (added prints that illustrate the problem before
the crash):
cfi_intelext_otp_walk walk OTP on chip 0 start at reg_prot_offset 0x00000100
ixp4xx_copy_from copy from 0x00000100 to 0xc880dd78
cfi_intelext_otp_walk walk OTP on chip 0 start at reg_prot_offset 0x12000000
ixp4xx_copy_from copy from 0x12000000 to 0xc880dd78
8<--- cut here ---
Unable to handle kernel paging request at virtual address db000000
[db000000] *pgd=00000000
(...)
This happens in this case because the IXP4xx is big endian and
the 32- and 16-bit fields in the struct cfi_intelext_otpinfo are not
properly byteswapped. Compare to how the code in read_pri_intelext()
byteswaps the fields in struct cfi_pri_intelext.
Adding a small byte swapping loop for the OTP in read_pri_intelext()
and the crash goes away.
The problem went unnoticed for many years until I enabled
CONFIG_MTD_OTP on the IXP4xx as well, triggering the bug.
Defining a prctl flag as an int is a footgun because on a 64 bit machine
and with a variadic implementation of prctl (like in musl and glibc), when
used directly as a prctl argument, it can get casted to long with garbage
upper bits which would result in unexpected behaviors.
This patch changes the constant to an unsigned long to eliminate that
possibilities. This does not break UAPI.
I think that a stable backport would be "nice to have": to reduce the
chances that users build binaries that could end up with garbage bits in
their MDWE prctl arguments. We are not aware of anyone having yet
encountered this corner case with MDWE prctls but a backport would reduce
the likelihood it happens, since this sort of issues has happened with
other prctls. But If this is perceived as a backporting burden, I suppose
we could also live without a stable backport.
Link: https://lkml.kernel.org/r/20230828150858.393570-5-revest@chromium.org Fixes: b507808ebce2 ("mm: implement memory-deny-write-execute as a prctl") Signed-off-by: Florent Revest <revest@chromium.org> Suggested-by: Alexey Izbyshev <izbyshev@ispras.ru> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Ayush Jain <ayush.jain3@amd.com> Cc: Greg Thelen <gthelen@google.com> Cc: Joey Gouly <joey.gouly@arm.com> Cc: KP Singh <kpsingh@kernel.org> Cc: Mark Brown <broonie@kernel.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Peter Xu <peterx@redhat.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Szabolcs Nagy <Szabolcs.Nagy@arm.com> Cc: Topi Miettinen <toiwoton@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dealing with hugetlb pages, manipulating struct page pointers
directly can get to wrong struct page, since struct page is not guaranteed
to be contiguous on SPARSEMEM without VMEMMAP. Use pfn calculation to
handle it properly.
Without the fix, a wrong number of page might be skipped. Since skip cannot be
negative, scan_movable_page() will end early and might miss a movable page with
-ENOENT. This might fail offline_pages(). No bug is reported. The fix comes
from code inspection.
Link: https://lkml.kernel.org/r/20230913201248.452081-4-zi.yan@sent.com Fixes: eeb0efd071d8 ("mm,memory_hotplug: fix scan_movable_pages() for gigantic hugepages") Signed-off-by: Zi Yan <ziy@nvidia.com> Reviewed-by: Muchun Song <songmuchun@bytedance.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch series "Use nth_page() in place of direct struct page manipulation",
v3.
On SPARSEMEM without VMEMMAP, struct page is not guaranteed to be
contiguous, since each memory section's memmap might be allocated
independently. hugetlb pages can go beyond a memory section size, thus
direct struct page manipulation on hugetlb pages/subpages might give wrong
struct page. Kernel provides nth_page() to do the manipulation properly.
Use that whenever code can see hugetlb pages.
This patch (of 5):
When dealing with hugetlb pages, manipulating struct page pointers
directly can get to wrong struct page, since struct page is not guaranteed
to be contiguous on SPARSEMEM without VMEMMAP. Use nth_page() to handle
it properly.
Without the fix, page_kasan_tag_reset() could reset wrong page tags,
causing a wrong kasan result. No related bug is reported. The fix
comes from code inspection.
Link: https://lkml.kernel.org/r/20230913201248.452081-1-zi.yan@sent.com Link: https://lkml.kernel.org/r/20230913201248.452081-2-zi.yan@sent.com Fixes: 2813b9c02962 ("kasan, mm, arm64: tag non slab memory allocated via pagealloc") Signed-off-by: Zi Yan <ziy@nvidia.com> Reviewed-by: Muchun Song <songmuchun@bytedance.com> Cc: David Hildenbrand <david@redhat.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the cmma no-dat feature is available the kernel page tables are walked
to identify and mark all pages which are used for address translation (all
region, segment, and page tables). In a subsequent loop all other pages are
marked as "no-dat" pages with the ESSA instruction.
This information is visible to the hypervisor, so that the hypervisor can
optimize purging of guest TLB entries. The initial loop however is
incorrect: only the first three of the four pages which belong to segment
and region tables will be marked as being used for DAT. The last page is
incorrectly marked as no-dat.
If the cmma no-dat feature is available all pages that are not used for
dynamic address translation are marked as "no-dat" with the ESSA
instruction. This information is visible to the hypervisor, so that the
hypervisor can optimize purging of guest TLB entries. This also means that
pages which are used for dynamic address translation must not be marked as
"no-dat", since the hypervisor may then incorrectly not purge guest TLB
entries.
Region and segment tables allocated via vmem_crst_alloc() are incorrectly
marked as "no-dat", as soon as slab_is_available() returns true.
Such tables are allocated e.g. when kernel page tables are split, memory is
hotplugged, or a DCSS segment is loaded.
Fix this by adding the missing arch_set_page_dat() call.
In case of the prep descriptor while the channel is already running, the
CCR register value stored into the channel could already have its EN bit
set. This would lead to a bad transfer since, at start transfer time,
enabling the channel while other registers aren't yet properly set.
To avoid this, ensure to mask the CCR_EN bit when storing the ccr value
into the mdma channel structure.
chameleon_parse_gdd() may fail for different reasons and end up
in the err tag. Make sure we at least always free the mcb_device
allocated with mcb_alloc_dev().
If mcb_device_register() fails, make sure to give up the reference
in the same place the device was added.
Fixes: 728ac3389296 ("mcb: mcb-parse: fix error handing in chameleon_parse_gdd()") Cc: stable <stable@kernel.org> Reviewed-by: Jose Javier Rodriguez Barbarin <JoseJavier.Rodriguez@duagon.com> Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com> Link: https://lore.kernel.org/r/20231019141434.57971-2-jorge.sanjuangarcia@duagon.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes a bug in commit 9ed9895370ae ("driver core: Functional
dependencies tracking support") where the device link status was
incorrectly updated in the driver unbind path before all the device's
resources were released.
Fixes: 9ed9895370ae ("driver core: Functional dependencies tracking support") Cc: stable <stable@kernel.org> Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Closes: https://lore.kernel.org/all/20231014161721.f4iqyroddkcyoefo@pengutronix.de/ Signed-off-by: Saravana Kannan <saravanak@google.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Yang Yingliang <yangyingliang@huawei.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Mark Brown <broonie@kernel.org> Cc: Matti Vaittinen <mazziesaccount@gmail.com> Cc: James Clark <james.clark@arm.com> Acked-by: "Rafael J. Wysocki" <rafael@kernel.org> Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20231018013851.3303928-1-saravanak@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A synthetic event is created by the synthetic event interface that can
read both user or kernel address memory. In reality, it reads any
arbitrary memory location from within the kernel. If the address space is
in USER (where CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE is set) then
it uses strncpy_from_user_nofault() to copy strings otherwise it uses
strncpy_from_kernel_nofault().
But since both functions use the same variable there's no annotation to
what that variable is (ie. __user). This makes sparse complain.
Quiet sparse by typecasting the strncpy_from_user_nofault() variable to
a __user pointer.
Link: https://lore.kernel.org/linux-trace-kernel/20231031151033.73c42e23@gandalf.local.home Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Fixes: 0934ae9977c2 ("tracing: Fix reading strings from synthetic events"); Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202311010013.fm8WTxa5-lkp@intel.com/ Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When execute the following command to test clone3 under !CONFIG_TIME_NS:
# make headers && cd tools/testing/selftests/clone3 && make && ./clone3
we can see the following error info:
# [7538] Trying clone3() with flags 0x80 (size 0)
# Invalid argument - Failed to create new process
# [7538] clone3() with flags says: -22 expected 0
not ok 18 [7538] Result (-22) is different than expected (0)
...
# Totals: pass:18 fail:1 xfail:0 xpass:0 skip:0 error:0
This is because if CONFIG_TIME_NS is not set, but the flag
CLONE_NEWTIME (0x80) is used to clone a time namespace, it
will return -EINVAL in copy_time_ns().
If kernel does not support CONFIG_TIME_NS, /proc/self/ns/time
will be not exist, and then we should skip clone3() test with
CLONE_NEWTIME.
With this patch under !CONFIG_TIME_NS:
# make headers && cd tools/testing/selftests/clone3 && make && ./clone3
...
# Time namespaces are not supported
ok 18 # SKIP Skipping clone3() with CLONE_NEWTIME
...
# Totals: pass:18 fail:0 xfail:0 xpass:0 skip:1 error:0
Link: https://lkml.kernel.org/r/1689066814-13295-1-git-send-email-yangtiezhu@loongson.cn Fixes: 515bddf0ec41 ("selftests/clone3: test clone3 with CLONE_NEWTIME") Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Suggested-by: Thomas Gleixner <tglx@linutronix.de> Cc: Christian Brauner <brauner@kernel.org> Cc: Shuah Khan <shuah@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since bae1d3a05a8b, i2c transfers are non-atomic if preemption is
disabled. However, non-atomic i2c transfers require preemption (e.g. in
wait_for_completion() while waiting for the DMA).
panic() calls preempt_disable_notrace() before calling
emergency_restart(). Therefore, if an i2c device is used for the
restart, the xfer should be atomic. This avoids warnings like:
[ 12.667612] WARNING: CPU: 1 PID: 1 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch+0x33c/0x6b0
[ 12.676926] Voluntary context switch within RCU read-side critical section!
...
[ 12.742376] schedule_timeout from wait_for_completion_timeout+0x90/0x114
[ 12.749179] wait_for_completion_timeout from tegra_i2c_wait_completion+0x40/0x70
...
[ 12.994527] atomic_notifier_call_chain from machine_restart+0x34/0x58
[ 13.001050] machine_restart from panic+0x2a8/0x32c
Use !preemptible() instead, which is basically the same check as
pre-v5.2.
Fixes: bae1d3a05a8b ("i2c: core: remove use of in_atomic()") Cc: stable@vger.kernel.org # v5.2+ Suggested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> Acked-by: Wolfram Sang <wsa@kernel.org> Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> Tested-by: Nishanth Menon <nm@ti.com> Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com> Link: https://lore.kernel.org/r/20230327-tegra-pmic-reboot-v7-2-18699d5dcd76@skidata.com Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the emergency restart does not call kernel_restart_prepare(), the
system_state stays in SYSTEM_RUNNING.
Since bae1d3a05a8b, this hinders i2c_in_atomic_xfer_mode() from becoming
active, and therefore might lead to avoidable warnings in the restart
handlers, e.g.:
[ 12.667612] WARNING: CPU: 1 PID: 1 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch+0x33c/0x6b0
[ 12.676926] Voluntary context switch within RCU read-side critical section!
...
[ 12.742376] schedule_timeout from wait_for_completion_timeout+0x90/0x114
[ 12.749179] wait_for_completion_timeout from tegra_i2c_wait_completion+0x40/0x70
...
[ 12.994527] atomic_notifier_call_chain from machine_restart+0x34/0x58
[ 13.001050] machine_restart from panic+0x2a8/0x32c
Avoid these by setting the correct system_state.
Fixes: bae1d3a05a8b ("i2c: core: remove use of in_atomic()") Cc: stable@vger.kernel.org # v5.2+ Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> Tested-by: Nishanth Menon <nm@ti.com> Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com> Link: https://lore.kernel.org/r/20230327-tegra-pmic-reboot-v7-1-18699d5dcd76@skidata.com Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit d7e7b9af104c ("fscrypt: stop using keyrings subsystem for
fscrypt_master_key"), xfstest generic/270 causes a WARNING when run on
f2fs with test_dummy_encryption in the mount options:
The cause of the WARNING is that not all encrypted inodes have been
evicted before fscrypt_destroy_keyring() is called, which violates an
assumption. This happens because the test uses an external quota file,
which gets automatically encrypted due to test_dummy_encryption.
Encryption of quota files has never really been supported. On ext4,
ext4_quota_read() does not decrypt the data, so encrypted quota files
are always considered invalid on ext4. On f2fs, f2fs_quota_read() uses
the pagecache, so trying to use an encrypted quota file gets farther,
resulting in the issue described above being possible. But this was
never intended to be possible, and there is no use case for it.
Therefore, make the quota support layer explicitly reject using
IS_ENCRYPTED inodes when quotaon is attempted.
Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230905003227.326998-1-ebiggers@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
JBD2 makes sure journal data is fallen on fs device by sync_blockdev(),
however, other process could intercept the EIO information from bdev's
mapping, which leads journal recovering successful even EIO occurs during
data written back to fs device.
We found this problem in our product, iscsi + multipath is chosen for block
device of ext4. Unstable network may trigger kpartx to rescan partitions in
device mapper layer. Detailed process is shown as following:
mount kpartx irq
jbd2_journal_recover
do_one_pass
memcpy(nbh->b_data, obh->b_data) // copy data to fs dev from journal
mark_buffer_dirty // mark bh dirty
vfs_read
generic_file_read_iter // dio
filemap_write_and_wait_range
__filemap_fdatawrite_range
do_writepages
block_write_full_folio
submit_bh_wbc
>> EIO occurs in disk <<
end_buffer_async_write
mark_buffer_write_io_error
mapping_set_error
set_bit(AS_EIO, &mapping->flags) // set!
filemap_check_errors
test_and_clear_bit(AS_EIO, &mapping->flags) // clear!
err2 = sync_blockdev
filemap_write_and_wait
filemap_check_errors
test_and_clear_bit(AS_EIO, &mapping->flags) // false
err2 = 0
Filesystem is mounted successfully even data from journal is failed written
into disk, and ext4/ocfs2 could become corrupted.
Fix it by comparing the wb_err state in fs block device before recovering
and after recovering.
A reproducer can be found in the kernel bugzilla referenced below.
Driver compares widget name in wsa_macro_spk_boost_event() widget event
callback, however it does not handle component's name prefix. This
leads to using uninitialized stack variables as registers and register
values. Handle gracefully such case.
Fixes: 2c4066e5d428 ("ASoC: codecs: lpass-wsa-macro: add dapm widgets and route") Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20231003155422.801160-1-krzysztof.kozlowski@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB Compact Keyboard variant requires a reset_resume function to
restore keyboard configuration after a suspend in some situations. Move
configuration normally done on probe to lenovo_features_set_cptkbd(), then
recycle this for use on reset_resume.
Without, the keyboard and driver would end up in an inconsistent state,
breaking middle-button scrolling amongst other problems, and twiddling
sysfs values wouldn't help as the middle-button mode won't be set until
the driver is reloaded.
Tested on a USB and Bluetooth Thinkpad Compact Keyboard.
CC: stable@vger.kernel.org Fixes: 94eefa271323 ("HID: lenovo: Use native middle-button mode for compact keyboards") Signed-off-by: Jamie Lentin <jm@lentin.co.uk> Signed-off-by: Martin Kepplinger <martink@posteo.de> Link: https://lore.kernel.org/r/20231002150914.22101-1-martink@posteo.de Signed-off-by: Benjamin Tissoires <bentiss@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initial value of 5% chosen for the maximum allowed percentage
difference between resctrl mbm value and IMC mbm value in
commit 06bd03a57f8c ("selftests/resctrl: Fix MBA/MBM results reporting
format") was "randomly chosen value" (as admitted by the changelog).
When running tests in our lab across a large number platforms, 5%
difference upper bound for success seems a bit on the low side for the
MBA and MBM tests. Some platforms produce outliers that are slightly
above that, typically 6-7%, which leads MBA/MBM test frequently
failing.
Replace the "randomly chosen value" with a success bound that is based
on those measurements across large number of platforms by relaxing the
MBA/MBM success bound to 8%. The relaxed bound removes the failures due
the frequent outliers.
Fixed commit description style error during merge:
Shuah Khan <skhan@linuxfoundation.org>
_GNU_SOURCE is defined in resctrl.h. Defining _GNU_SOURCE has a large
impact on what gets defined when including headers either before or
after it. This can result in compile failures if .c file decides to
include a standard header file before resctrl.h.
It is safer to define _GNU_SOURCE in Makefile so it is always defined
regardless of in which order includes are done.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com> Reviewed-by: Reinette Chatre <reinette.chatre@intel.com> Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com> Cc: <stable@vger.kernel.org> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The test runner run_cmt_test() in resctrl_tests.c checks for CMT
feature and does not run cmt_resctrl_val() if CMT is not supported.
Then cmt_resctrl_val() also check is CMT is supported.
Remove the duplicated feature check for CMT from cmt_resctrl_val().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Tested-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com> Reviewed-by: Reinette Chatre <reinette.chatre@intel.com> Reviewed-by: Shaopeng Tan <tan.shaopeng@jp.fujitsu.com> Cc: <stable@vger.kernel.org> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
signal_handler_unregister() calls sigaction() with uninitializing
sa_flags in the struct sigaction.
Make sure sa_flags is always initialized in signal_handler_unregister()
by initializing the struct sigaction when declaring it. Also add the
initialization to signal_handler_register() even if there are no know
bugs in there because correctness is then obvious from the code itself.
Fixes: 73c55fa5ab55 ("selftests/resctrl: Commonize the signal handler register/unregister for all tests") Suggested-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Cc: <stable@vger.kernel.org> Reviewed-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current setup the PA is left unmuted even when the
Soundwire ports are not started streaming. This can lead to click
and pop sounds during start.
There is a same issue in the reverse order where in the PA is
left unmute even after the data stream is stopped, the time
between data stream stopping and port closing is long enough
to accumulate DC on the line resulting in Click/Pop noise
during end of stream.
making use of new mute_unmute_on_trigger flag is helping a
lot with this Click/Pop issues reported on this Codec
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20231027105747.32450-3-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some setups like Speaker amps which are very sensitive, ex: keeping them
unmute without actual data stream for very short duration results in a
static charge and results in pop and clicks. To minimize this, provide a way
to mute and unmute such codecs during trigger callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20231027105747.32450-2-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org>
[ johan: backport to v6.6.2 ] Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
list_for_each_entry_safe() does not work for the async case which runs
under RCU, therefore, split GC logic for catchall in two functions
instead, one for each of the sync and async GC variants.
The catchall sync GC variant never sees a _DEAD bit set on ever, thus,
this handling is removed in such case, moreover, allocate GC sync batch
via GFP_KERNEL.
Fixes: 93995bf4af2c ("netfilter: nf_tables: remove catchall element in GC sync path") Reported-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The expired catchall element is not deactivated and removed from GC sync
path. This path holds mutex so just call nft_setelem_data_deactivate()
and nft_setelem_catchall_remove() before queueing the GC work.
Fixes: 4a9e12ea7e70 ("netfilter: nft_set_pipapo: call nft_trans_gc_queue_sync() in catchall GC") Reported-by: lonial con <kongln9170@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 18b44bc5a672 ("ovl: Always reevaluate the file signature for
IMA") forced signature re-evaulation on every file access.
Instead of always re-evaluating the file's integrity, detect a change
to the backing file, by comparing the cached file metadata with the
backing file's metadata. Verifying just the i_version has not changed
is insufficient. In addition save and compare the i_ino and s_dev
as well.
Reviewed-by: Amir Goldstein <amir73il@gmail.com> Tested-by: Eric Snowberg <eric.snowberg@oracle.com> Tested-by: Raul E Rangel <rrangel@chromium.org> Cc: stable@vger.kernel.org Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not clear that IMA should be nested at all, but as long is it
measures files both on overlayfs and on underlying fs, we need to
annotate the iint mutex to avoid lockdep false positives related to
IMA + overlayfs, same as overlayfs annotates the inode mutex.
The Qualcomm SPMI PMIC revid implementation is broken in multiple ways.
First, it assumes that just because the sibling base device has been
registered that means that it is also bound to a driver, which may not
be the case (e.g. due to probe deferral or asynchronous probe). This
could trigger a NULL-pointer dereference when attempting to access the
driver data of the unbound device.
Second, it accesses driver data of a sibling device directly and without
any locking, which means that the driver data may be freed while it is
being accessed (e.g. on driver unbind).
Third, it leaks a struct device reference to the sibling device which is
looked up using the spmi_device_from_of() every time a function (child)
device is calling the revid function (e.g. on probe).
Fix this mess by reimplementing the revid lookup so that it is done only
at probe of the PMIC device; the base device fetches the revid info from
the hardware, while any secondary SPMI device fetches the information
from the base device and caches it so that it can be accessed safely
from its children. If the base device has not been probed yet then probe
of a secondary device is deferred.
Fixes: e9c11c6e3a0e ("mfd: qcom-spmi-pmic: expose the PMIC revid information to clients") Cc: stable@vger.kernel.org # 6.0 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Caleb Connolly <caleb.connolly@linaro.org> Link: https://lore.kernel.org/r/20231003152927.15000-3-johan+linaro@kernel.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm SPMI PMIC revid implementation is broken in multiple ways.
First, it totally ignores struct device_node reference counting and
leaks references to the parent bus node as well as each child it
iterates over using an open-coded for_each_child_of_node().
Second, it leaks references to each spmi device on the bus that it
iterates over by failing to drop the reference taken by the
spmi_device_from_of() helper.
Fix the struct device_node leaks by reimplementing the lookup using
for_each_child_of_node() and adding the missing reference count
decrements. Fix the sibling struct device leaks by dropping the
unnecessary lookups of devices with the wrong USID.
Note that this still leaves one struct device reference leak in case a
base device is found but it is not the parent of the device used for the
lookup. This will be addressed in a follow-on patch.
Fixes: e9c11c6e3a0e ("mfd: qcom-spmi-pmic: expose the PMIC revid information to clients") Cc: stable@vger.kernel.org # 6.0 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Caleb Connolly <caleb.connolly@linaro.org> Link: https://lore.kernel.org/r/20231003152927.15000-2-johan+linaro@kernel.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCC 13.2 complains about array subscript 17 is above array bounds of
'char[16]' with IFNAMSIZ set to 16.
The warning is correct but this scenario is impossible.
set_device_name is called by device_name_store (store sysfs entry) and
netdev_trig_activate.
device_name_store already check if size is >= of IFNAMSIZ and return
-EINVAL. (making the warning scenario impossible)
netdev_trig_activate works on already defined interface, where the name
has already been checked and should already follow the condition of
strlen() < IFNAMSIZ.
Aside from the scenario being impossible, set_device_name can be
improved to both mute the warning and make the function safer.
To make it safer, move size check from device_name_store directly to
set_device_name and prevent any out of bounds scenario.
Cc: stable@vger.kernel.org Fixes: 28a6a2ef18ad ("leds: trigger: netdev: refactor code setting device name") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202309192035.GTJEEbem-lkp@intel.com/ Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Link: https://lore.kernel.org/r/20231007131042.15032-1-ansuelsmth@gmail.com Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per the "SMC calling convention specification", the 64-bit calling
convention can only be used when the client is 64-bit. Whereas the
32-bit calling convention can be used by either a 32-bit or a 64-bit
client.
Currently during SCM probe, irrespective of the client, 64-bit calling
convention is made, which is incorrect and may lead to the undefined
behaviour when the client is 32-bit. Let's fix it.
[ 444.853098] BUG: KASAN: global-out-of-bounds in param_get_int+0x77/0x90
[ 444.853111] Read of size 4 at addr ffffffffc16c9220 by task cat/2105
...
[ 444.853442] The buggy address belongs to the variable:
[ 444.853443] max_idle+0x0/0xffffffffffffcde0 [intel_powerclamp]
There is a mismatch between the param_get_int and the definition of
max_idle. Replacing param_get_int with param_get_byte resolves this
issue.
Fixes: ebf519710218 ("thermal: intel: powerclamp: Add two module parameters") Cc: 6.3+ <stable@vger.kernel.org> # 6.3+ Signed-off-by: David Arcari <darcari@redhat.com> Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a random schedule_timeout() if the current transaction is
committing, which seems to be a holdover from the original delalloc
reservation code.
Remove this, we have the proper flushing stuff, we shouldn't be hoping
for random timing things to make everything work. This just induces
latency for no reason.
CC: stable@vger.kernel.org # 5.4+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the actual slab freeing is deferred when calling kvfree_rcu(), so
is the kmemleak_free() callback informing kmemleak of the object
deletion. From the perspective of the kvfree_rcu() caller, the object is
freed and it may remove any references to it. Since kmemleak does not
scan RCU internal data storing the pointer, it will report such objects
as leaks during the grace period.
Tell kmemleak to ignore such objects on the kvfree_call_rcu() path. Note
that the tiny RCU implementation does not have such issue since the
objects can be tracked from the rcu_ctrlblk structure.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Christoph Paasch <cpaasch@apple.com> Closes: https://lore.kernel.org/all/F903A825-F05F-4B77-A2B5-7356282FBA2C@apple.com/ Cc: <stable@vger.kernel.org> Tested-by: Christoph Paasch <cpaasch@apple.com> Reviewed-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In snapshot_write_next(), sync_read is set and unset in three different
spots unnecessiarly. As a result there is a subtle bug where the first
page after the meta data has been loaded unconditionally sets sync_read
to 0. If this first PFN was actually a highmem page, then the returned
buffer will be the global "buffer," and the page needs to be loaded
synchronously.
That is, I'm not sure we can always assume the following to be safe:
We found at least one situation where the safe pages list was empty and
get_buffer() would gladly try to use a NULL pointer.
Signed-off-by: Brian Geffon <bgeffon@google.com> Fixes: 8357376d3df2 ("[PATCH] swsusp: Improve handling of highmem") Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are instances where rcu_cpu_stall_reset() is called when jiffies
did not get a chance to update for a long time. Before jiffies is
updated, the CPU stall detector can go off triggering false-positives
where a just-started grace period appears to be ages old. In the past,
we disabled stall detection in rcu_cpu_stall_reset() however this got
changed [1]. This is resulting in false-positives in KGDB usecase [2].
Fix this by deferring the update of jiffies to the third run of the FQS
loop. This is more robust, as, even if rcu_cpu_stall_reset() is called
just before jiffies is read, we would end up pushing out the jiffies
read by 3 more FQS loops. Meanwhile the CPU stall detection will be
delayed and we will not get any false positives.
When an RPC Call message cannot be pulled from the client, that
is a message loss, by definition. Close the connection to trigger
the client to resend.
Cc: <stable@vger.kernel.org> Reviewed-by: Tom Talpey <tom@talpey.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling KASAN and running some iperf tests raises some memory issues with
vmm_table:
BUG: KASAN: slab-out-of-bounds in wilc_wlan_handle_txq+0x6ac/0xdb4
Write of size 4 at addr c3a61540 by task wlan0-tx/95
KASAN detects that we are writing data beyond range allocated to vmm_table.
There is indeed a mismatch between the size passed to allocator in
wilc_wlan_init, and the range of possible indexes used later: allocation
size is missing a multiplication by sizeof(u32)
Fixes: 40b717bfcefa ("wifi: wilc1000: fix DMA on stack objects") Cc: stable@vger.kernel.org Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com> Reviewed-by: Michael Walle <mwalle@kernel.org> Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20231017-wilc1000_tx_oops-v3-1-b2155f1f7bee@bootlin.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux / log